; Copyright (c) TCC 1991. All rights reserved. ; No part may be reproduced, transmitted, transcribed, stored in retrieval ; system, or translated into any language or computer language, in any form ; or by any means, electronic, mechanical, magnetic, optical, manual, ; or otherwise, without prior written permission of TCC. ; ; Configuration file for the Adaptec AHA-1740 Standard ; @[#]ADP0000 1.20 91/10/22 ;=== Maintenance History ===================================================== ; ;Rev Date Name Comment ;---- -------- -- ---------------------------------------------- ;1.20 22.10.91 DM Removed non-English help directions ;1.10 30.09.91 TF Text edits for release. ;1.00 19.02.91 DM Initial release ; BOARD ID = "ADP0000" NAME = "Adaptec AHA-1740 EISA SCSI Host Adapter (Standard)" MFR = "ADAPTEC, Inc." CATEGORY = "MSD" SLOT = EISA LENGTH = 330 AMPERAGE = 2000 SKIRT = NO READID = YES BUSMASTER = 50 IOCHECK = VALID DISABLE = SUPPORTED COMMENTS = "Adaptec configuration file version 2.00" IOPORT(1) = 0zcc0h ;Group 1 port address INITVAL = XX000XXX IOPORT(2) = 0zcc1h ;BIOS address INITVAL = 1100XXXX IOPORT(3) = 0zcc2h ;Interrupt definition INITVAL = 000XXXXX IOPORT(4) = 0zcc3h ;SCSI definition INITVAL = 000XXXXX IOPORT(5) = 0zcc4h ;EISA bus definition INITVAL = 0000XX01 SOFTWARE(1) = "Note that the Standard AHA-1540 drivers for MS-DOS, Netware, UNIX, XENIX, and other operating systems may be used freely with the AHA-1740 in Standard Mode. If you wish to use Enhanced Mode drivers, you must reconfigure your AHA-1740 host adapter in Enhanced Mode and upgrade your software.\n\nThe Enhanced Mode drivers are NOT compatible with the AHA-1740 when operating in Standard Mode.\n\nThe following resource configuration information may be required by the Standard Mode driver for installation." SOFTWARE(2) = "Note that the Enhanced AHA-1740 drivers for MS-DOS, Netware, UNIX, XENIX, and other operating systems may be used freely with the AHA-1740 in Enhanced Mode. If you wish to use Standard Mode drivers, you must reconfigure your AHA-1740 host adapter in Standard Mode and upgrade your software.\n\nThe Standard Mode drivers are NOT compatible with the AHA-1740 when operating in Enhanced Mode.\n\nThe following resource configuration information may be required by the Enhanced Mode driver for installation." FUNCTION = "Host Adapter Interface Mode" HELP = "The configuration program will automatically choose a unique IRQ level, and port address and DMA channel (if necessary) for each host adapter in the system.\n\nIf you wish to manually select these resources, see your MCS documentation for more information." COMMENTS = "Standard mode is an AHA-1540/1542 compatible interface that allows the use of AHA-1540/1542 software drivers. Enhanced mode is a higher performance interface that uses AHA-1740 software drivers. In standard mode, the system IRQ level, the host adapter port address, and the host adapter DMA channel must also be specified. The configuration program will automatically choose a unique IRQ, port address, and DMA channel for each host adapter in the system.\n\nIf you wish to manually select these resources, see your MCS documentation for more information." CHOICE = "AHA-1540 Standard Mode" FREE INIT = IOPORT(1) LOC (7 6) 00B LINK IRQ = 11 | 9 | 10 | 12 | 14 | 15 SHARE = NO TRIGGER = EDGE INIT = IOPORT(3) LOC(4 3 2 1 0) 11010B | 11000B | 11001B | 11011B | 11101B | 11110B INIT = SOFTWARE(1) "\tIRQ = 11" | "\tIRQ = 9" | "\tIRQ = 10" | "\tIRQ = 12" | "\tIRQ = 14" | "\tIRQ = 15" LINK PORT = 330H-333H | 230H-233H | 130H-133H | 334H-337H | 234H-237H | 134H-137H SHARE = NO SIZE = BYTE INIT = IOPORT(1) LOC (2 1 0) 110B | 100B | 010B | 111B | 101B | 011B INIT = SOFTWARE(1) "\tPORT = 330h-333h" | "\tPORT = 230h-233h" | "\tPORT = 130h-133h" | "\tPORT = 334h-337h" | "\tPORT = 234h-237h" | "\tPORT = 134h-137h" LINK DMA = 5 | 6 | 7 | 0 SHARE = NO INIT = IOPORT(5) LOC(3 2) 01B | 10B | 11B | 00B INIT = SOFTWARE(1) "\tDMA = 5" | "\tDMA = 6" | "\tDMA = 7" | "\tDMA = 0" CHOICE = "AHA-1740 Enhanced mode" FREE INIT = IOPORT(1) LOC (7 6 2 1 0) 10000B INIT = IOPORT(1) LOC (2 1 0) 000B INIT = IOPORT(5) LOC(3 2) 00B LINK IRQ = 11 | 9 | 10 | 12 | 14 | 15 SHARE = NO TRIGGER = LEVEL INIT = IOPORT(3) LOC(4 3 2 1 0) 10010B | 10000B | 10001B | 10011B | 10101B | 10110B INIT = SOFTWARE(2) "\tIRQ = 11" | "\tIRQ = 9" | "\tIRQ = 10" | "\tIRQ = 12" | "\tIRQ = 14" | "\tIRQ = 15" FUNCTION = "Host Adapter BIOS" HELP = "The configuration program will automatically choose a BIOS address for each host adapter in the system.\n\nIf you wish to manually select this resource, see your MCS documentation for more information." COMMENTS = "Select whether the AHA-1740 BIOS is to be enabled. Normally the BIOS should always be enabled, even if there are multiple AHA-1740 cards in the system.\n\nIf the BIOS is disabled it will not be possible to boot from any device attached to this host adapter, and the SCSI device configuration information will not be sent to the host adapter. The configuration program will automatically choose a BIOS address for each host adapter in the system.\n\nIf you wish to manually select this resource, see your MCS documentation for more information." CHOICE = "BIOS enabled" COMBINE MEMORY = 16K ADDRESS = 0CC000H | 0D0000H | 0D4000H | 0D8000H | 0DC000H | 0E0000H | 0E4000H | 0E8000H | 0EC000H WRITABLE = YES MEMTYPE = OTH SHARE = NO SIZE = BYTE CACHE = YES DECODE = 32 INIT = IOPORT(2) LOC(3 2 1 0) 0011B | 0100B | 0101B | 0110B | 0111B | 1000B | 1001B | 1010B | 1011B CHOICE = "BIOS disabled" DISABLE = YES FREE INIT = IOPORT(2) LOC(3 2 1 0) 0000B FUNCTION="Host Adapter SCSI ID" HELP = "Select the SCSI ID for the host adapter. ID 7 is normally reserved for the host adapter because it has the highest SCSI priority. In typical configurations where only one host adapter is connected to a single SCSI cable, this ID does not need to be changed, even if there are multiple host adapters installed in your system.\n\n For configurations with more than one host adapter attached to a single SCSI cable, unique ID's must be selected for each host adapter. Note: Care should be exercised when changing this ID. The EISA configuration can not detect SCSI bus configuration conflicts." COMMENTS = "Select the SCSI ID for the host adapter. ID 7 is normally reserved for the host adapter because it has the highest SCSI priority." CHOICE = "Device Id 7" LINK INIT = IOPORT(4) LOC(3 2 1 0) 0111B CHOICE = "Device Id 6" LINK INIT = IOPORT(4) LOC(3 2 1 0) 0110B CHOICE = "Device Id 5" LINK INIT = IOPORT(4) LOC(3 2 1 0) 0101B CHOICE = "Device Id 4" LINK INIT = IOPORT(4) LOC(3 2 1 0) 0100B CHOICE = "Device Id 3" LINK INIT = IOPORT(4) LOC(3 2 1 0) 0011B CHOICE = "Device Id 2" LINK INIT = IOPORT(4) LOC(3 2 1 0) 0010B CHOICE = "Device Id 1" LINK INIT = IOPORT(4) LOC(3 2 1 0) 0001B CHOICE = "Device Id 0" LINK INIT = IOPORT(4) LOC(3 2 1 0) 0000B FUNCTION = "SCSI Bus Reset at Power-on" HELP = "The SCSI bus reset at power-on should be disabled if a SCSI target does not initialize properly after a SCSI reset. If you have properly installed devices attached to the SCSI bus that are not detected, or reported as having a fault by the Adaptec BIOS, disabling the SCSI reset may correct the problem." COMMENTS = "When this option is enabled, a SCSI bus reset will be performed by the host adapter during its power-on initialization, and after a hard reset." CHOICE = "Enable SCSI bus reset" LINK INIT = IOPORT(4) LOC(4) 1B CHOICE = "Disable SCSI bus reset" LINK INIT = IOPORT(4) LOC (4) 0B INCLUDE = "ADP0000.OVL"