; This file is created by Tim Tran
; Acer America Corp
; All right reserved

BOARD
   ID = "ADP1522"
   NAME = "Adaptec AHA-1520/1522 ISA SCSI Host Adapter"
   MFR = "Adaptec, Inc."
   CATEGORY = "MSD"
   LENGTH = 330
   BUSMASTER = 50
   AMPERAGE = 1200
   COMMENTS = "AHA-1520B/1522B EISA Configuration File Version 1.00\n\n"
		
   HELP = "Select the desired AHA-1520/1522 configuration.  Then
	   use the configuration utility \"View Switches and Jumpers\"
	   option to verify that the AHA-1520/1522 jumpers have been 
	   set correctly for this configuration.  The default 
	   configuration is identical with the factory jumper settings."

JUMPER(5) = 8
     NAME = "J5"
     JTYPE = PAIRED
     VERTICAL = NO
     REVERSE = YES
     LABEL = LOC(1-8) "DT" 
		       "BT"
		       "M0"
		       "M1"
		       "SN"
		       "DN"
		       "R"
		       "R"
     FACTORY = LOC(1-8) 01001100
     
JUMPER(6) = 8
     NAME = "J6"
     JTYPE = PAIRED
     VERTICAL = YES
     REVERSE = NO
     LABEL = LOC(1-8) "SD"
		      "ID0"
		      "ID1"
		      "ID2"
		      "ID3"
		      "IC"
		      "DC"
		      "SP"
     FACTORY = LOC(1-8) 11101000

JUMPER(7) = 8
     NAME = "J7"
     JTYPE = PAIRED
     VERTICAL = YES
     REVERSE = YES
     LABEL = LOC(1-8) "Flpy Addr"
		      "DR"
		      "DR"
		      "DA"
		      "jmp16"
		      "jmp10"
		      "IRQ Chan"
		      "DS"
     FACTORY = LOC(1-8) 11010100


JUMPER(8) = 8
     NAME = "J8"
     JTYPE = PAIRED
     VERTICAL = YES
     REVERSE = YES
     LABEL = LOC(1-8) "DR"
		      "D6"
		      "D5"
		      "D0"
		      "DA"
		      "D6"
		      "D5"
		      "D0"
     FACTORY = LOC(1-8) 00010001

JUMPER(9) = 8
     NAME = "J9"
     JTYPE = PAIRED
     VERTICAL = YES
     REVERSE = YES
     LABEL = LOC(1-8) "12"
		      "11"
		      "10"
		      "19"
		      "AL"
		      "J6"
		      "J4"
		      "BE"
     FACTORY = LOC(1-8) 01000111



GROUP = "Host Adapter System Resources"
	TYPE = "MSD"

	 


FUNCTION = "BIOS Base Address"
	TYPE = "NET"
	COMMENTS = "Select the host adapter BIOS base address. 
		    This selection must correspond with the Jumper setting
		    of Jumper J9 positions 6 and 7.  The BIOS enable jumper
		    on position 8 must also be set to reflect whether 
		    or not the BIOS is enabled."
	HELP = "Select the base address in system optional ROM memory
		for the host adapter BIOS.  The BIOS will begin at the 
		specified address and is 16KB in length.  The BIOS address
		select jumpers on jumper block J7 positions 7 and 8 must be
		configured to reflect the choices made in this menu.  Use the 
		configuration utility \"View Jumpers and Switches\" option
		to determine the correct jumper settings."
	   
	CHOICE = "Base Address C000"
		COMBINE
		MEMORY=16K
		ADDRESS=0C000H
		WRITABLE=NO
		MEMTYPE = OTH
		SHARE=NO
		SIZE=BYTE
		CACHE=YES
		DECODE=24
		INIT = JUMPER(9) LOC(6 7 8) 111            
	  FREE
		DMA = 0
		SHARE = NO
		INIT = JUMPER(6) LOC(6 7) 00
		INIT = JUMPER(8) LOC(4 8) 11 
	  LINK
		 IRQ = 11|12|10|9
		 TRIGGER = EDGE
		 SHARE = NO
		 INIT = JUMPER(6) LOC(4 5) 01|11|10|00 
		 INIT = JUMPER(9) LOC(1-4) 0100|1000|0010|0001
	  
	   FREE
		 PORT = 340h-35Eh
		 INIT = JUMPER(9) LOC(5) 0
	   FREE
		 PORT = 140h-15Eh  
		 INIT = JUMPER(9) LOC(5)  1

	CHOICE = "Base Address C8000"
		COMBINE
		MEMORY=16K
		ADDRESS=0C8000H
		WRITABLE=NO
		MEMTYPE = OTH
		SHARE=NO
		SIZE=BYTE
		CACHE=YES
		DECODE=24
		INIT = JUMPER(9) LOC(6 7 8) 001            
	  FREE
		DMA = 0
		SHARE = NO
		INIT = JUMPER(6) LOC(6 7) 00
		INIT = JUMPER(8) LOC(4 8) 11 
	  LINK
		 IRQ = 11|12|10|9
		 TRIGGER = EDGE
		 SHARE = NO
		 INIT = JUMPER(6) LOC(4 5) 01|11|10|00 
		 INIT = JUMPER(9) LOC(1-4) 0100|1000|0010|0001
	   
	   FREE
		 PORT = 340h-35Eh
		 INIT = JUMPER(9) LOC(5) 0
	   FREE
		 PORT = 140h-15Eh  
		 INIT = JUMPER(9) LOC(5)  1
		       
	CHOICE = "Base Address CC000"
		COMBINE        
		MEMORY=16K
		ADDRESS=0CC000H
		WRITABLE=NO
		MEMTYPE = OTH
		SHARE=NO
		SIZE=BYTE
		CACHE=YES
		DECODE=24
		INIT = JUMPER(9) LOC(6 7 8) 011            
		
	  FREE
		DMA = 0
		SHARE = NO
		INIT = JUMPER(6) LOC(6 7) 00
		INIT = JUMPER(8) LOC(4 8) 11 
	  LINK
		 IRQ = 11|12|10|9
		 TRIGGER = EDGE
		 SHARE = NO
		 INIT = JUMPER(6) LOC(4 5) 01|11|10|00 
		 INIT = JUMPER(9) LOC(1-4) 0100|1000|0010|0001
	   
	   FREE
		 PORT = 340h-35Eh
		 INIT = JUMPER(9) LOC(5) 0
	   FREE
		 PORT = 140h-15Eh  
		 INIT = JUMPER(9) LOC(5)  1
	
	CHOICE = "Base Address D8000"
		COMBINE
		MEMORY=16K
		ADDRESS=0D8000H
		WRITABLE=NO
		MEMTYPE = OTH
		SHARE=NO
		SIZE=BYTE
		CACHE=YES
		DECODE=24
		INIT = JUMPER(9) LOC(6 7 8) 101            
		
	  FREE
		DMA = 0
		SHARE = NO
		INIT = JUMPER(6) LOC(6 7) 00
		INIT = JUMPER(8) LOC(4 8) 11 
	  LINK
		 IRQ = 11|12|10|9
		 TRIGGER = EDGE
		 SHARE = NO
		 INIT = JUMPER(6) LOC(4 5) 01|11|10|00 
		 INIT = JUMPER(9) LOC(1-4) 0100|1000|0010|0001
	   
	   FREE
		 PORT = 340h-35Eh
		 INIT = JUMPER(9) LOC(5) 0
	   FREE
		 PORT = 140h-15Eh  
		 INIT = JUMPER(9) LOC(5)  1

	CHOICE =  "BIOS Disabled"
		DISABLE = YES
		LINK
		INIT = JUMPER(7) LOC(8) 0            
		
SUBFUNCTION = "DMA DISABLE"
	COMMENTS = "This function to disable the DMA." 
	HELP = "To disable DMA using PIO J5(DT=0), J6(DC-DC=0) 
	and J8 (D0-D0 = 0)" 

	CHOICE = "DMA Disabled"        
		DISABLE = YES
		LINK
		INIT = JUMPER(5) LOC(1) 0
		INIT = JUMPER(6) LOC(6 7) 00
		INIT = JUMPER(8) LOC(4 8) 00 

ENDGROUP



GROUP = "Host Adapter SCSI Configuration"

FUNCTION = "Synchronous Transfers"

	COMMENTS = "When enabled, the host adapter will initiate synchronous
		    transfer negotiation for SCSI transfers.  The synchronous 
		    transfer jumper, pin 5 of J5, must be installed if this 
		    feature is enabled."
	HELP = "The host adapter can be configured to initiate synchronous 
		transfer negotiation with SCSI target devices.  With devices 
		that support synchronous transfers, but do not initiate 
		synchronous negotiation, it is necessary to enable this option
		if the faster synchronous transfers are desired.  The synchronous
		transfer jumper, pin 1 of J5, must be installed if this feature
		is enabled.  Use the configuration utility \"View Jumpers and 
		Switches\" option to determine the correct jumper settings."

	CHOICE = "Do Not Initiate Sync Transfers"
		LINK
		INIT = JUMPER(5) LOC(5) 0

	CHOICE = "Initiate Sync Transfers"
		LINK
		INIT = JUMPER(5) LOC(5) 1

FUNCTION = "SCSI Parity"
	COMMENTS = "When enabled, the host adapter will check parity
		    on SCSI transfers. The parity disable jumper, pin 8 of
		    J6, must be installed if this feature is disabled."
	HELP = "The host adapter normally performs parity checking on SCSI
		transfers.  Some devices do not support parity.  If you wish
		to use a device that does not use parity, you must insert
		the parity disable jumper.  The jumper location is position
		8 on jumper block J6.  Use the configuration utility 
		\"View Jumpers and Switches\" option to determine the
		correct jumper settings."


	CHOICE = "SCSI Parity Enabled"
		LINK
		INIT = JUMPER(6) LOC(8) 0

	CHOICE = "SCSI Parity Disabled"
		LINK
		INIT = JUMPER(6) LOC(8) 0

FUNCTION = "Host Adapter SCSI Address"

	COMMENTS = "Select the host adapter SCSI ID.  This is normally set
		    to ID 0, which has the highest SCSI priority.  If you 
		    need to change the SCSI ID, the SCSI address select 
		    jumpers must be configured to match the SCSI ID desired.
		    These are located at positions 1, 2 and 3 of J6."
	HELP = "Each device connected to the SCSI bus, including the
		AHA-1520B/1522B must have a unique SCSI ID number.  The 
		host adapter is normally configured for ID 0, which has the 
		highest priority on the SCSI bus.  This value normally only
		needs to be changed when more than one host adapter is
		attached to the same SCSI bus.  If this option is changed, 
		the SCSI address selection jumpers at positions 1, 2 and 3 of
		jumper block J6 must be configured to select the desired 
		SCSI ID.  Use the configuration utility \"View Jumpers
		and Switches\" option to determine the correct jumper 
		settings."
					       

	CHOICE = "SCSI ID 0"
		LINK
		INIT = JUMPER(6) LOC(1 2 3) 000
	
	CHOICE = "SCSI ID 1"
		LINK
		INIT = JUMPER(6) LOC(1 2 3) 100
	
	CHOICE = "SCSI ID 2"
		LINK
		INIT = JUMPER(6) LOC(1 2 3) 010
	
	CHOICE = "SCSI ID 3"
		LINK
		INIT = JUMPER(6) LOC(1 2 3) 110
	
	CHOICE = "SCSI ID 4"
		LINK
		INIT = JUMPER(6) LOC(1 2 3) 001
	
	CHOICE = "SCSI ID 5"
		LINK
		INIT = JUMPER(6) LOC(1 2 3) 101
	
	CHOICE = "SCSI ID 6"
		LINK
		INIT = JUMPER(6) LOC(1 2 3) 011
	
	CHOICE = "SCSI ID 7"
		LINK
		INIT = JUMPER(6) LOC(1 2 3) 111

FUNCTION = "DATA TRANSFER MODE"

	COMMENTS = "Need to change SCSI Data transfer mode,  
		    jumpers must be configured to match the desired.
		    These are located at positions 1 of J5."
	HELP = "Each device connected to the SCSI bus, including the
		AHA-1520B/1522B must have a unique Transfer Mode. 
		PIO, and 2nd_Party DMA are the selections. Position 1   
		jumper block J5 must be configured to select the desired 
		Transfer Mode.  Use the configuration utility \"View Jumpers
		and Switches\" option to determine the correct jumper 
		settings."
					       

	CHOICE = "PIO"
		LINK
		INIT = JUMPER(5) LOC(1) 0
	
	CHOICE = "2nd-Party DMA"
		LINK
		INIT = JUMPER(5) LOC(1) 1


FUNCTION = "BOOT OPERATION"

	COMMENTS = "Need to change SCSI Boot Operation Mode,  
		    jumpers must be configured to match the desired.
		    These are located at positions 2 of J5."
	HELP = "Each device connected to the SCSI bus, including the
		AHA-1520B/1522B must have a unique Boot Operation Mode. 
		Boot from SCSI Disk or Disable this function. Position 2   
		jumper block J5 must be configured to select the desired 
		Boot Operation.  Use the configuration utility \"View Jumpers
		and Switches\" option to determine the correct jumper 
		settings."
					       

	CHOICE = "Boot from HD"
		LINK
		INIT = JUMPER(5) LOC(2) 1
	
	CHOICE = "Disable BT"
		LINK
		INIT = JUMPER(5) LOC(2) 0

FUNCTION = "MESSAGE DISPLAY"

	COMMENTS = "Need to change SCSI Message Display Mode,  
		    jumpers must be configured to match the desired.
		    These are located at positions 3 and 4 of J5."
	HELP = "Each device connected to the SCSI bus, including the
		AHA-1520B/1522B must have a unique Message Display. 
		Position 3 and 4 jumper block J6 must be configured to select the desired 
		Message Display.  Use the configuration utility \"View Jumpers
		and Switches\" option to determine the correct jumper 
		settings."
					       

	CHOICE = "Header and Error Message"
		LINK
		INIT = JUMPER(5) LOC(3 4) 00
	
	CHOICE = "Header, Boot, Error Message"
		LINK
		INIT = JUMPER(5) LOC(3 4) 01
	
	CHOICE = "SCSI Inf. Jumper Cofig. Boot, Error Message"
		LINK
		INIT = JUMPER(5) LOC(3 4) 10
	
	CHOICE = "Only Error Message"
		LINK
		INIT = JUMPER(5) LOC(3 4) 11


	
ENDGROUP

GROUP = "AHA-1522B Floppy Controller (Disable if using AHA-1520B)"
	TYPE = "MSD,FPYCTL"

FUNCTION = "Floppy Contoller Port"
	COMMENTS = "Select the floppy controller address, or disable the 
		    floppy controller on the AHA-1522B.  
		    The floppy IRQ and DMA channels are automatically 
		    selected when this choice is made.  Floppy enable jumper 
		    at position 1 of J7 must be set to reflect the choices made.
		    The floppy IRQ and DMA jumpers at J7 locations 2 through
		    7 must also be configured."
    
		
	HELP = "Select the floppy controller address, or disable the 
		floppy controller on the AHA-1522B.  If the AHA-1522B is the 
		only floppy controller in your system, the primary address
		should normally be selected. Floppy enable jumper at
		position 1 of J7 must be set to reflect the choices made.
		The floppy IRQ and DMA jumpers at J8 locations 2 through
		7 must also be configured.  Use the configuration utility
		\"View Jumpers and Switches\" option to determine the correct
		jumper settings."
		
	CHOICE = "FLPY DMA CHANNEL 2"       
		LINK
		DMA = 2
		SHARE = NO
		INIT = JUMPER(7) LOC(2-5) 1010

	CHOICE = "FLPY DMA CHANNEL 3"         
		LINK                
		DMA = 3
		SHARE = NO
		INIT = JUMPER(7) LOC(2-5) 0101

	CHOICE = "FLPY IRQ CHANNEL 6"         
		LINK                
		IRQ = 6
		SHARE = NO
		INIT = JUMPER(7) LOC(6 7) 10

	CHOICE = "FLPY IRQ CHANNEL 10"         
		LINK                
		IRQ = 10
		SHARE = NO
		INIT = JUMPER(7) LOC(6 7) 01

	CHOICE = "Floppy Disabled"
		DISABLE = YES
		LINK
		INIT = JUMPER(7) LOC(1) 0

FUNCTION = "Floppy Spindle Speed"

	COMMENTS = "When enabled, the AHA-1522B floppy controller can support
		    dual speed floppy drives.  The dual speed floppy jumper
		    at position 8 of J7 must correspond to this selection."
	HELP = "If you wish to use a floppy drive that supports dual spindle 
		speed operation, the host adapter can be configured to be
		compatible drive.  Normally this feature is disabled, and the 
		floppy drive operates at a single speed.  To configure the 
		AHA-1522B for dual speed floppy drives, a jumper is installed
		at position 8 of jumper block J7.  Use the configuration
		utility \"View Jumpers and Switches\" option to determine
		the correct jumper settings."

	CHOICE = "Disable Dual Speed"
		LINK
		INIT = JUMPER(7) LOC(8) 0

	CHOICE = "Dual Speed Floppy Drive"
		LINK
		INIT = JUMPER(7) LOC(8) 1

ENDGROUP