;	 CFG file for : AMI VLB SINGLE ENDED EISA SCSI CACHING
;		      : HOST ADAPTER [SERIES 70]
;	      Version : 1.01 (June 28, 1993)
;	      Version : 1.02 (December 3, 1993)

BOARD
	ID = "AMI7001"
	NAME = "AMI Fast Single Ended VLB SCSI CACHING Controller"
	MFR = "AMI,GA,USA"
	CATEGORY = "MSD"
	SLOT = EISA
	DISABLE = UNSUPPORTED
	READID = YES
	LENGTH = 338

SWITCH(1) = 2
	NAME = "SW1"
	STYPE = DIP
	VERTICAL = NO
	REVERSE = YES
	INITVAL = LOC(1 2) 10
	FACTORY = LOC(1 2) 10
	LABEL	= LOC(1 2) "Floppy" "Diag"
	COMMENTS = "Diag Switch should be set to OFF position for normal mode
		    of operation.  Floppy Switch should be set to ON position
		    to enable Floppy controller interface." 

IOPORT(1) = 0z800H
IOPORT(2) = 0z801H
	INITVAL=LOC(7-0) 000xxxxx
IOPORT(3) = 0zC8Ah
IOPORT(4) = 0zC96h
	INITVAL = LOC(7-0) 0xxxxxxx
IOPORT(5) = 0zC97h
	INITVAL = LOC(7-0) 0xx0xxxx
IOPORT(6) = 0zC94h
	INITVAL = LOC(7-0) 0xxxxxxx
IOPORT(7) = 0zC99h
	INITVAL = LOC(7-0) 0000xxxx
IOPORT(8) = 0zC9Bh
	INITVAL = LOC(7-0) 00xxxx00
IOPORT(9) = 0zC92h
	INITVAL = LOC(7-0) 0xxxxxxx
IOPORT(10) = 0zC9Ch
	INITVAL = LOC(7-0) 0xxx0xxx
IOPORT(11) = 0zC9Dh
	INITVAL = LOC(7-0) 0xxx0xxx
IOPORT(12) = 0zC9Eh
	INITVAL = LOC(7-0) 0xxx0xxx
IOPORT(13) = 0zC9Fh
	INITVAL = LOC(7-0) 00000xxx
IOPORT(14) = 0zC95h
	INITVAL = LOC(7-0) 0xxxxxxx

FUNCTION = "FLOPPY CONTROLLER"

	SUBFUNCTION = "FLOPPY PORT(3F0h-3F7h) ENABLE/DISABLE"

		CHOICE = "FLOPPY PORT ENABLED"
			FREE
				DMA = 2
				IRQ = 6
				PORT = 03F0h - 03F7h
				INIT = IOPORT(2) LOC(0) 0

		CHOICE = "FLOPPY PORT DISABLED"
			FREE
				INIT = IOPORT(2) LOC(0) 1

FUNCTION = "SCSI DISK CONTROLLER"

	SUBFUNCTION = "DMA CHANNEL SELECTION"

		CHOICE = "DMA CHANNEL 5"
			FREE
				DMA = 5
				INIT = IOPORT(1) LOC(1 0) 00
				INIT = IOPORT(8) LOC(4) 0

		CHOICE = "DMA CHANNEL 6"
			FREE
				DMA = 6
				INIT = IOPORT(1) LOC(1 0) 01
				INIT = IOPORT(8) LOC(4) 0

		CHOICE = "DMA CHANNEL 7"
			FREE
				DMA = 7
				INIT = IOPORT(1) LOC(1 0) 10
				INIT = IOPORT(8) LOC(4) 0

		CHOICE = "DMA CHANNEL 0"
			FREE
				DMA = 0
				INIT = IOPORT(1) LOC(1 0) 11
				INIT = IOPORT(8) LOC(4) 0

		CHOICE = "NO DMA CHANNEL"
			FREE
				INIT = IOPORT(1) LOC(1 0) 11
				INIT = IOPORT(8) LOC(4) 1

	SUBFUNCTION = "IRQ CHANNEL SELECTION"

		CHOICE = "IRQ 11 [Edge Triggered]"
			FREE
				IRQ = 11
				TRIGGER = EDGE
				SHARE = NO
				INIT = IOPORT(2) LOC(4) 0
				INIT = IOPORT(1) LOC(4 3 2) 000

		CHOICE = "IRQ 10 [Edge Triggered]"
			FREE
				IRQ = 10
				TRIGGER = EDGE
				SHARE = NO
				INIT = IOPORT(2) LOC(4) 0
				INIT = IOPORT(1) LOC(4 3 2) 010
		CHOICE = "IRQ 12 [Edge Triggered]"
			FREE
				IRQ = 12
				TRIGGER = EDGE
				SHARE = NO
				INIT = IOPORT(2) LOC(4) 0
				INIT = IOPORT(1) LOC(4 3 2) 011
		CHOICE = "IRQ 14 [Edge Triggered]"
			FREE
				IRQ = 14
				TRIGGER = EDGE
				SHARE = NO
				INIT = IOPORT(2) LOC(4) 0
				INIT = IOPORT(1) LOC(4 3 2) 100

		CHOICE = "IRQ 15 [Edge Triggered]"
			FREE
				IRQ = 15
				TRIGGER = EDGE
				SHARE = NO
				INIT = IOPORT(2) LOC(4) 0
				INIT = IOPORT(1) LOC(4 3 2) 101

		CHOICE = "IRQ 9 [Edge Triggered]"
			FREE
				IRQ = 9
				TRIGGER = EDGE
				SHARE = NO
				INIT = IOPORT(2) LOC(4) 0
				INIT = IOPORT(1) LOC(4 3 2) 001

		CHOICE = "IRQ 11 [Level Triggered]"
			FREE
				IRQ = 11
				TRIGGER = LEVEL
				SHARE = YES
				INIT = IOPORT(2) LOC(4) 1
				INIT = IOPORT(1) LOC(4 3 2) 000

		CHOICE = "IRQ 10 [Level Triggered]"
			FREE
				IRQ = 10
				TRIGGER = LEVEL
				SHARE = YES
				INIT = IOPORT(2) LOC(4) 1
				INIT = IOPORT(1) LOC(4 3 2) 010

		CHOICE = "IRQ 12 [Level Triggered]"
			FREE
				IRQ = 12
				TRIGGER = LEVEL
				SHARE = YES
				INIT = IOPORT(2) LOC(4) 1
				INIT = IOPORT(1) LOC(4 3 2) 011

		CHOICE = "IRQ 14 [Level Triggered]"
			FREE
				IRQ = 14
				TRIGGER = LEVEL
				SHARE = YES
				INIT = IOPORT(2) LOC(4) 1
				INIT = IOPORT(1) LOC(4 3 2) 100

		CHOICE = "IRQ 15 [Level Triggered]"
			FREE
				IRQ = 15
				TRIGGER = LEVEL
				SHARE = YES
				INIT = IOPORT(2) LOC(4) 1
				INIT = IOPORT(1) LOC(4 3 2) 101

		CHOICE = "IRQ 9 [Level Triggered]"
			FREE
				IRQ = 9
				TRIGGER = LEVEL
				SHARE = YES
				INIT = IOPORT(2) LOC(4) 1
				INIT = IOPORT(1) LOC(4 3 2) 001

	SUBFUNCTION = "HOST BIOS ROM ADDRESS SELECTION"

		CHOICE = "ROM AT C8000H-CBFFFH"
			COMBINE
				MEMORY = 16K
				ADDRESS = 0C8000H
				WRITABLE = NO
				SIZE = BYTE
				INIT = IOPORT(1) LOC(7 6 5) 000

		CHOICE = "ROM DISABLED"
			FREE
				INIT = IOPORT(1) LOC(7 6 5) 111

		CHOICE = "ROM AT CC000H-CFFFFH"
			COMBINE
				MEMORY = 16K
				ADDRESS = 0CC000H
				WRITABLE = NO
				SIZE = BYTE
				INIT = IOPORT(1) LOC(7 6 5) 100

		CHOICE = "ROM AT D0000H-D3FFFH"
			COMBINE
				MEMORY = 16K
				ADDRESS = 0D0000H
				WRITABLE = NO
				SIZE = BYTE
				INIT = IOPORT(1) LOC(7 6 5) 011

		CHOICE = "ROM AT D4000H-D7FFFH"
			COMBINE
				MEMORY = 16K
				ADDRESS = 0D4000H
				WRITABLE = NO
				SIZE = BYTE
				INIT = IOPORT(1) LOC(7 6 5) 010

		CHOICE = "ROM AT D8000H-DBFFFH"
			COMBINE
				MEMORY = 16K
				ADDRESS = 0D8000H
				WRITABLE = NO
				SIZE = BYTE
				INIT = IOPORT(1) LOC(7 6 5) 001

		CHOICE = "ROM AT DC000H-DFFFFH"
			COMBINE
				MEMORY = 16K
				ADDRESS = 0DC000H
				WRITABLE = NO
				SIZE = BYTE
				INIT = IOPORT(1) LOC(7 6 5) 101

	SUBFUNCTION = "HOST ADAPTER I/O PORT ADDRESS SELECTION"

		CHOICE = "330h-333h"
			FREE
				PORT = 330h-333h
				INIT = IOPORT(2) LOC(3 2 1) 000

		CHOICE = "130h-133h"
			FREE
				PORT = 130h-133h
				INIT = IOPORT(2) LOC(3 2 1) 001

		CHOICE = "230h-233h"
			FREE
				PORT = 230h-233h
				INIT = IOPORT(2) LOC(3 2 1) 010

		CHOICE = "334h-337h"
			FREE
				PORT = 334h-337h
				INIT = IOPORT(2) LOC(3 2 1) 100

		CHOICE = "134h-137h"
			FREE
				PORT = 134h-137h
				INIT = IOPORT(2) LOC(3 2 1) 101

		CHOICE = "234h-237h"
			FREE
				PORT = 234h-237h
				INIT = IOPORT(2) LOC(3 2 1) 110

GROUP = "SCSI CONTROLLER OPTIONS"

	FUNCTION = "ENTER CONFIG MODE"

		SHOW = NO

		CHOICE = "RESERVE SEMAPHORE PORT 0"
			FREE
				INIT = IOPORT(3) 00000001

	FUNCTION = "CACHE SIZE"

		CHOICE = "ALL INSTALLED MEMORY"
			FREE
				INIT = PORTADR (0zC9Ah) 00000000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = "15 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 11110000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = "14 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 11100000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = "13 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 11010000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = "12 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 11000000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = "11 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 10110000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = "10 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 10100000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = " 9 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 10010000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = " 8 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 10000000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = " 7 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 01110000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = " 6 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 01100000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = " 5 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 01010000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = " 4 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 01000000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = " 3 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 00110000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = " 2 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 00100000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = " 1 MB"
			FREE
				INIT = PORTADR (0zC9Ah) 00010000
				INIT = PORTADR (0zC90h) 01111111

		CHOICE = "CACHE DISABLED"
			FREE
				INIT = PORTADR (0zC9Ah) 00000000
				INIT = PORTADR (0zC90h) 00000000

	FUNCTION = "PRE READ IN CACHE"

		CHOICE = "ENABLED"
			FREE
				INIT = IOPORT(4) LOC(2) 1

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(4) LOC(2) 0

	FUNCTION = "SINGLE SECTOR SEPERATE CACHING"

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(5) LOC(5) 1

		CHOICE = "ENABLED"
			FREE
				INIT = IOPORT(5) LOC(5) 0

	FUNCTION = "REMOVABLE HARDDISK CACHING"

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(5) LOC(6) 0

		CHOICE = "ENABLED"
			FREE
				INIT = IOPORT(5) LOC(6) 1

	FUNCTION = "DELAYED WRITE ENABLE/DISABLE"

		CHOICE = "ENABLED"
			FREE
				INIT = PORTADR (0zC91h) 01111111

		CHOICE = "DISABLED"
			FREE
				INIT = PORTADR (0zC91h) 00000000

	FUNCTION = "DELAYED WRITE TIME OUT"

		CHOICE = "5 SECONDS"
			FREE
				INIT = PORTADR (0zC98h) 00110010

		CHOICE = "0.1 SECOND"
			FREE
				INIT = PORTADR (0zC98h) 00000001

		CHOICE = "0.2 SECOND"
			FREE
				INIT = PORTADR (0zC98h) 00000010

		CHOICE = "0.5 SECOND"
			FREE
				INIT = PORTADR (0zC98h) 00000101

		CHOICE = "1 SECOND"
			FREE
				INIT = PORTADR (0zC98h) 00001010

		CHOICE = "2 SECONDS"
			FREE
				INIT = PORTADR (0zC98h) 00010100

		CHOICE = "10 SECONDS"
			FREE
				INIT = PORTADR (0zC98h) 01100100

		CHOICE = "20 SECONDS"
			FREE
				INIT = PORTADR (0zC98h) 11001000

		CHOICE = "25 SECONDS"
			FREE
				INIT = PORTADR (0zC98h) 11111010

;	WARNING: If this choice is used, the only way to flush data to disk
;		 is by using the flush utility or flush drivers!!!
;		CHOICE = "NEVER FLUSH DUE TO A TIMEOUT"
;			FREE
;				INIT = PORTADR (0zC98h) 00000000

	FUNCTION = "PARITY CHECK"

		CHOICE = "ENABLED"
			FREE
				INIT = IOPORT(6) LOC(6 5 4 3 2 1 0) 1111111

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(6) LOC(6 5 4 3 2 1 0) 0000000

	FUNCTION = "DISCONNECT"

		CHOICE = "ENABLED"
			FREE
				INIT = PORTADR (0zC93h) 01111111

		CHOICE = "DISABLED"
			FREE
				INIT = PORTADR (0zC93h) 00000000
	FUNCTION = "Synchronous Negotiation"


		SUBFUNCTION = "Target ID (0)"

		COMMENTS="The controller will initiated the procedure of transferring data
			in a synchronous pattern to and from the SCSI devices by sending
			a synchronous data transfer message to the SCSI device.
			There are some older firmware drives that will incorrectly respond
			to the FAST SCSI (10Mb/s) selection, and therefore under these circ
			NORMAL SCSI (5Mb/s) or DISABLED (4Mb/s) must be selected." 

		CHOICE = "ENABLED [FAST SCSI]"
			FREE
				INIT = IOPORT(14) LOC(0) 1
				INIT = IOPORT(9) LOC(0) 1
				INIT = IOPORT(10) LOC(2 1 0) 001

		CHOICE = "ENABLED [NORMAL SCSI]"
			FREE
				INIT = IOPORT(14) LOC(0) 1
				INIT = IOPORT(9) LOC(0) 0
				INIT = IOPORT(10) LOC(2 1 0) 001

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(14) LOC(0) 0

		SUBFUNCTION = "Target ID (1)"

		COMMENTS="The controller will initiated the procedure of transferring data
			in a synchronous pattern to and from the SCSI devices by sending
			a synchronous data transfer message to the SCSI device.
			There are some older firmware drives that will incorrectly respond
			to the FAST SCSI selection, and therefore under these circumstance
			NORMAL SCSI or DISABLED must be selected." 
		CHOICE = "ENABLED [FAST SCSI]"
			FREE
				INIT = IOPORT(14) LOC(1) 1
				INIT = IOPORT(9) LOC(1) 1
				INIT = IOPORT(10) LOC(6 5 4) 001

		CHOICE = "ENABLED [NORMAL SCSI]"
			FREE
				INIT = IOPORT(14) LOC(1) 1
				INIT = IOPORT(9) LOC(1) 0
				INIT = IOPORT(10) LOC(6 5 4) 001

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(14) LOC(1) 0

		SUBFUNCTION = "Target ID (2) "

		COMMENTS="The controller will initiated the procedure of transferring data
			in a synchronous pattern to and from the SCSI devices by sending
			a synchronous data transfer message to the SCSI device.
			There are some older firmware drives that will incorrectly respond
			to the FAST SCSI selection, and therefore under these circumstance
			NORMAL SCSI or DISABLED must be selected." 
		CHOICE = "ENABLED [FAST SCSI]"
			FREE
				INIT = IOPORT(14) LOC(2) 1
				INIT = IOPORT(9) LOC(2) 1
				INIT = IOPORT(11) LOC(2 1 0) 001

		CHOICE = "ENABLED [NORMAL SCSI]"
			FREE
				INIT = IOPORT(14) LOC(2) 1
				INIT = IOPORT(9) LOC(2) 0
				INIT = IOPORT(11) LOC(2 1 0) 001

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(14) LOC(2) 0

		SUBFUNCTION = "Target ID (3)"

		COMMENTS="The controller will initiated the procedure of transferring data
			in a synchronous pattern to and from the SCSI devices by sending
			a synchronous data transfer message to the SCSI device.
			There are some older firmware drives that will incorrectly respond
			to the FAST SCSI selection, and therefore under these circumstance
			NORMAL SCSI or DISABLED must be selected." 
		CHOICE = "ENABLED [FAST SCSI]"
			FREE
				INIT = IOPORT(14) LOC(3) 1
				INIT = IOPORT(9) LOC(3) 1
				INIT = IOPORT(11) LOC(6 5 4) 001

		CHOICE = "ENABLED [NORMAL SCSI]"
			FREE
				INIT = IOPORT(14) LOC(3) 1
				INIT = IOPORT(9) LOC(3) 0
				INIT = IOPORT(11) LOC(6 5 4) 001

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(14) LOC(3) 0

		SUBFUNCTION = "Target ID (4)"

		COMMENTS="The controller will initiated the procedure of transferring data
			in a synchronous pattern to and from the SCSI devices by sending
			a synchronous data transfer message to the SCSI device.
			There are some older firmware drives that will incorrectly respond
			to the FAST SCSI selection, and therefore under these circumstance
			NORMAL SCSI or DISABLED must be selected." 
		CHOICE = "ENABLED [FAST SCSI]"
			FREE
				INIT = IOPORT(14) LOC(4) 1
				INIT = IOPORT(9) LOC(4) 1
				INIT = IOPORT(12) LOC(2 1 0) 001

		CHOICE = "ENABLED [NORMAL SCSI]"
			FREE
				INIT = IOPORT(14) LOC(4) 1
				INIT = IOPORT(9) LOC(4) 0
				INIT = IOPORT(12) LOC(2 1 0) 001

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(14) LOC(4) 0

		SUBFUNCTION = "Target ID (5)"

		COMMENTS="The controller will initiated the procedure of transferring data
			in a synchronous pattern to and from the SCSI devices by sending
			a synchronous data transfer message to the SCSI device.
			There are some older firmware drives that will incorrectly respond
			to the FAST SCSI selection, and therefore under these circumstance
			NORMAL SCSI or DISABLED must be selected." 
		CHOICE = "ENABLED [FAST SCSI]"
			FREE
				INIT = IOPORT(14) LOC(5) 1
				INIT = IOPORT(9) LOC(5) 1
				INIT = IOPORT(12) LOC(6 5 4) 001

		CHOICE = "ENABLED [NORMAL SCSI]"
			FREE
				INIT = IOPORT(14) LOC(5) 1
				INIT = IOPORT(9) LOC(5) 0
				INIT = IOPORT(12) LOC(6 5 4) 001

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(14) LOC(5) 0

		SUBFUNCTION = "Target ID (6)"

		COMMENTS="The controller will initiated the procedure of transferring data
			in a synchronous pattern to and from the SCSI devices by sending
			a synchronous data transfer message to the SCSI device.
			There are some older firmware drives that will incorrectly respond
			to the FAST SCSI selection, and therefore under these circumstance
			NORMAL SCSI or DISABLED must be selected." 
		CHOICE = "ENABLED [FAST SCSI]"
			FREE
				INIT = IOPORT(14) LOC(6) 1
				INIT = IOPORT(9) LOC(6) 1
				INIT = IOPORT(13) LOC(2 1 0) 001

		CHOICE = "ENABLED [NORMAL SCSI]"
			FREE
				INIT = IOPORT(14) LOC(6) 1
				INIT = IOPORT(9) LOC(6) 0
				INIT = IOPORT(13) LOC(2 1 0) 001

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(14) LOC(6) 0


	FUNCTION = "FAST MODE ENABLE ON TARGET BASIS"

		SHOW = NO

		CHOICE = "ENABLED"
			FREE
				INIT = IOPORT(8) LOC(2) 1

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(8) LOC(2) 0


	FUNCTION = "SYNCHRONOUS OFFSET SELECTION"

		CHOICE = "8"
			FREE
				INIT = IOPORT(7) LOC(3 2 1 0) 1000

		CHOICE = "1"
			FREE
				INIT = IOPORT(7) LOC(3 2 1 0) 0001

		CHOICE = "2"
			FREE
				INIT = IOPORT(7) LOC(3 2 1 0) 0010

		CHOICE = "3"
			FREE
				INIT = IOPORT(7) LOC(3 2 1 0) 0011

		CHOICE = "4"
			FREE
				INIT = IOPORT(7) LOC(3 2 1 0) 0100

		CHOICE = "5"
			FREE
				INIT = IOPORT(7) LOC(3 2 1 0) 0101

		CHOICE = "6"
			FREE
				INIT = IOPORT(7) LOC(3 2 1 0) 0110

		CHOICE = "7"
			FREE
				INIT = IOPORT(7) LOC(3 2 1 0) 0111

		CHOICE = "0"
			FREE
				INIT = IOPORT(7) LOC(3 2 1 0) 0000

	FUNCTION = "ABOVE ONE GB DRIVE SUPPORT UNDER DOS"

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(5) LOC(0) 0

		CHOICE = "ENABLED"
			FREE
				INIT = IOPORT(5) LOC(0) 1

	FUNCTION = "SEVEN DRIVE SUPPORT UNDER DOS"

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(5) LOC(1) 0

		CHOICE = "ENABLED"
			FREE
				INIT = IOPORT(5) LOC(1) 1

	FUNCTION = "TARGET ALLOCATION FOR DOS SEQUENTIALLY FROM TARGET ID 0"

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(5) LOC(2) 0

		CHOICE = "ENABLED"
			FREE
				INIT = IOPORT(5) LOC(2) 1

	FUNCTION = "EXTENDED MODE {or 32-bit Driver Mode}"

		CHOICE = "ENABLED"
			FREE
				INIT = IOPORT(4) LOC(0) 1

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(4) LOC(0) 0

	FUNCTION = "SEND *START UNIT* COMMAND at POST"

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(8) LOC(5) 0

		CHOICE = "ENABLED"
			FREE
				INIT = IOPORT(8) LOC(5) 1

	FUNCTION = "AUTO SELECTION TIMEOUT FOR NON-EXISTENT DEVICES"

		CHOICE = "ENABLED"
			FREE
				INIT = IOPORT(4) LOC(1) 1

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(4) LOC(1) 0

	FUNCTION = "NON CACHING DEVICES BUFFER SIZE SELECTION"

		CHOICE = "16 KB"
			FREE
				INIT = IOPORT(4) LOC(6 5 4) 000

		CHOICE = "512 BYTES"
			FREE
				INIT = IOPORT(4) LOC(6 5 4) 001

		CHOICE = "1 KB"
			FREE
				INIT = IOPORT(4) LOC(6 5 4) 010

		CHOICE = "2 KB"
			FREE
				INIT = IOPORT(4) LOC(6 5 4) 011

		CHOICE = "4 KB"
			FREE
				INIT = IOPORT(4) LOC(6 5 4) 100

		CHOICE = "8 KB"
			FREE
				INIT = IOPORT(4) LOC(6 5 4) 101

		CHOICE = "32 KB"
			FREE
				INIT = IOPORT(4) LOC(6 5 4) 110

		CHOICE = "64 KB"
			FREE
				INIT = IOPORT(4) LOC(6 5 4) 111

	FUNCTION = "BMIC CHANNEL 0/1 SELECTION"

		CHOICE = "CHANNEL 1"
			FREE
				INIT = IOPORT(4) LOC(3) 1

		CHOICE = "CHANNEL 0"
			FREE
				INIT = IOPORT(4) LOC(3) 0

	FUNCTION = "BMIC 32/64 BCLK SUPPORT"

		CHOICE = "32 BCLK"
			FREE
				INIT = IOPORT(5) LOC(3) 0

		CHOICE = "64 BCLK"
			FREE
				INIT = IOPORT(5) LOC(3) 1

	FUNCTION = "RESERVED OPTION"

		SHOW = NO

		CHOICE = "ENABLED"
			FREE
				INIT = IOPORT(8) LOC(3) 1

		CHOICE = "DISABLED"
			FREE
				INIT = IOPORT(8) LOC(3) 0

	FUNCTION = "EXIT CONFIG MODE"
		SHOW = NO

		CHOICE = "INTERRUPT THE CONTROLLER"
			FREE
				INIT = PORTADR (0zC8Dh) 00000010

ENDGROUP