;
; ATI AT-1700 Series Ethernet Adapter Card
; configuration file version 1.03
; !ATI1700.CFG   07-15-1996
;
; (C)Copyright ATI, 1992-1996
;    All Rights Reserved.
;

BOARD            
  ID        = "ATI1700"
  NAME      = "ATI AT-1700 Ethernet Adapter Card"
  MFR       = "ATI "
  CATEGORY  = "NET"
  SLOT      = ISA16
  LENGTH    = 165
  AMPERAGE  = 500
  BUSMASTER = 40
  COMMENTS  = "The ATI AT-1700 Ethernet Adapter Card
	       is a 16-bit local area networking board.\n\n
	       This EISA configuration utility tells your computer
	       what resources are reserved for the AT-1700 Adapter
	       Card. After determining available I/O resources, you
	       should run the program SETUP17.EXE, which is on
	       the ATI CardAssistant diskette, to configure
	       the board for the parameters I/O Address Range
	       and Interrupt Channel (IRQ). Then you can use this
	       utility to add the values you chose for these
	       parameters to your computer's EISA configuration table."
  HELP      = 
	      "The ATI AT-1700 network adapter connects
	       your personal computer to an 802.3 local
	       area network.\n\n
	       Refer to the adapter card user manual for
	       additional information on configuring
	       this adapter using SETUP17.EXE."

SOFTWARE(1) = "
  NOTE: Use SETUP17.EXE on the ATI CardAssistant diskette to
  change and verify configuration of the card itself. Then update this
  utility (step 3). THE CARD AND EISA TABLE SHOULD AGREE. Make a
  note of these values. Your network operating system may ask for them.\n
  \n
  The following configuration parameter values are currently selected:"


FUNCTION="I/O Address Range"
    HELP   =
	       "The I/O Address Range must match the
	       value set in SETUP17.EXE on the ATI
	       AT-1700 CardAssistant diskette."
    CHOICE = "300h - 31fh (Factory default)"
      LINK
	PORT = 300h - 31fh
	INIT = SOFTWARE(1) "I/O Range: 300h-31fh"
    CHOICE = "240h - 25fh"
      LINK
	PORT = 240h - 25fh
	INIT = SOFTWARE(1) "I/O Range: 240h-25fh"
    CHOICE = "260h - 27fh"
      LINK
	PORT = 260h - 27fh
	INIT = SOFTWARE(1) "I/O Range: 260h-27fh"
    CHOICE = "280h - 29fh"
      LINK
	PORT = 280h - 29fh
	INIT = SOFTWARE(1) "I/O Range: 280h-29fh"
    CHOICE = "2a0h - 2bfh"
      LINK
	PORT = 2a0h - 2bfh
	INIT = SOFTWARE(1) "I/O Range: 2a0h-2bfh"
    CHOICE = "320h - 33fh"
      LINK
	PORT = 320h - 33fh
	INIT = SOFTWARE(1) "I/O Range: 320h-33fh"
    CHOICE = "340h - 35fh"
      LINK
	PORT = 340h - 35fh
	INIT = SOFTWARE(1) "I/O Range: 340h-35fh"
    CHOICE = "380h - 39fh"
      LINK
	PORT = 380h - 39fh
	INIT = SOFTWARE(1) "I/O Range: 380h-39fh"

FUNCTION = "Interrupt Channel (IRQ)"
    HELP   =
	       "The Interrupt Channel (IRQ) must match the
	       value set in SETUP17.EXE on the ATI
	       AT-1700 CardAssistant diskette."
    CHOICE = "15 (Factory default)"
      LINK
	IRQ = 15
	INIT = Software(1) "IRQ = 15"
    CHOICE = "3"
      LINK
	IRQ = 3
	INIT = Software(1) "IRQ = 3"
    CHOICE = "4"
      LINK
	IRQ = 4
	INIT = Software(1) "IRQ = 4"
    CHOICE = "5"
      LINK
	IRQ = 5
	INIT = Software(1) "IRQ = 5"
    CHOICE = "9"
      LINK
	IRQ = 9
	INIT = Software(1) "IRQ = 9"
    CHOICE = "10"
      LINK
	IRQ = 10
	INIT = Software(1) "IRQ = 10"
    CHOICE = "11"
      LINK
	IRQ = 11
	INIT = Software(1) "IRQ = 11"
    CHOICE = "12"
      LINK
	IRQ = 12
	INIT = Software(1) "IRQ = 12"