;
;	Chase Research Intelligent Serial I/O Controllers
;	=================================================
;
;	Module:	EISA config files ( ISA cards )
;	File:	!CHAA091.CFG
;	Author:	Paula Martin
;	Version:1.00
;	Created:21 May 90
;
;	Copyright 1990 Chase Research plc.
;	All rights reserved.
;
;	EISA configuration file for Chase AT8+ board
;
;	This file is required for the configuration of a Chase AT8+ controller
;	card in an EISA machine.
;
;	Revision History
;
;	When	   Who		What and Why
;	====	   ===		============
;

;	Describe the board

BOARD
    ID =	"CHAA091"
    NAME =	"Chase AT8+ Intelligent Serial Controller"
    MFR =	"Chase Research plc"
    CATEGORY =	"COM"
    SLOT =	ISA16
    LENGTH =	339
    AMPERAGE =	2000
    SKIRT =	NO
    READID =	NO
    BUSMASTER =	100	;Chase cards actually have no maximum latency
			; restriction but there is no way to specify this and
			; still specify a bus master device.
    IOCHECK =	INVALID
    DISABLE =	UNSUPPORTED
    COMMENTS =	"This intelligent serial I/O controller
		 supports eight asynchronous RS232
		 communications ports with their own
		 dedicated I/O processor."
    HELP =	"Upto 4 Chase AT cards may be installed
		 at any one time allowing for a maximum
		 of 64 ports. As it may be necessary to
		 change links on the AT boards having
		 selected a configuration it is advisable
		 to run this configuration program before
		 the cards are installed in order to
		 check the link settings. Further
		 information can be found in the User
		 Manual.
		 All Chase AT cards are interoperable
		 with the Chase EISA cards which support
		 EISA automatic jumperless configuration."

;	Describe jumpers for DMA

JUMPER(1) =	7
    NAME =	"LK1A"
    JTYPE =	PAIRED
    VERTICAL =	NO
    REVERSE =	YES
    LABEL =	LOC ( 1-7 ) "0""1""2""3""5""6""7"	;Skip DMA 4 ( cascade )
    FACTORY =	LOC ( 1-7 ) 0000100
    COMMENTS =	"This link field selects the DMA channel
		 used by the card. It must have the same
		 setting as linkfield LK1B."
    HELP =	"The first card installed in a system
		 (the master)normally uses DMA channel 5
		 with the slaves using channels 6, 7 and
		 then 0 in turn as they are added to the
		 system.
		 If these values are changed it will be
		 necessary to reconfigure the operating
		 system device driver."

JUMPER(2) =	7
    NAME =	"LK1B"
    JTYPE =	PAIRED
    VERTICAL =	NO
    REVERSE =	YES
    LABEL =	LOC ( 1-7 ) "0""1""2""3""5""6""7"	;Skip DMA 4 ( cascade )
    FACTORY =	LOC ( 1-7 ) 0000100
    COMMENTS =	"This link field selects the DMA channel
		 used by the card. It must have the same
		 setting as linkfield LK1A."
    HELP =	"The first card installed in a system
		 (the master)normally uses DMA channel 5
		 with the slaves using channels 6, 7 and
		 then 0 in turn as they are added to the
		 system.
		 If these values are changed it will be
		 necessary to reconfigure the operating
		 system device driver."

;	Describe interrupt jumpers

JUMPER(3) =	8
    NAME =	"LK2 lower pair"
    JTYPE =	PAIRED
    VERTICAL =	NO
    REVERSE =	NO
    LABEL =	LOC ( 8-1 ) "15""12""11""10""7""5""4""3"
    FACTORY =	LOC ( 8-1 ) 00010000
    COMMENTS =  "This link field selects the two
		 interrupts used by the master (or first)
		 card installed. A link on the upper pair
		 of pins selects the CCI interrupt and on
		 the lower pair the CAI interrupt.
		 Subsequent slave cards use no interrupts
		 and should not have any links installed
		 in this field."
    HELP =	"The cards as supplied use interrupt line
		 10 for the CAI and 15 for the CCI.
		 If these values are changed it will be
		 necessary to reconfigure the operating
		 system device driver."

JUMPER(4) =	8
    NAME =	"LK2 upper pair"
    JTYPE =	PAIRED
    VERTICAL =	NO
    REVERSE =	NO
    LABEL =	LOC ( 8-1 ) "15""12""11""10""7""5""4""3"
    FACTORY =	LOC ( 8-1 ) 10000000
    COMMENTS =  "This link field selects the two
		 interrupts used by the master (or first)
		 card installed. A link on the upper pair
		 of pins selects the CCI interrupt and on
		 the lower pair the CAI interrupt.
		 Subsequent slave cards use no interrupts
		 and should not have any links installed
		 in this field."
    HELP =	"The cards as supplied use interrupt line
		 10 for the CAI and 15 for the CCI.
		 If these values are changed it will be
		 necessary to reconfigure the operating
		 system device driver."

;	Describe remaining jumpers

JUMPER(5) =	2
    NAME =	"LK3"
    JTYPE =	PAIRED
    VERTICAL =  YES
    REVERSE =	NO
    LABEL =	LOC ( 2-1 ) "Master""Slave"
    FACTORY =	LOC ( 2-1 ) 00
    COMMENTS =	"This is not a true link field but is
		 used to connect the inter-card linking
		 strap. The first card ( or master )has
		 the strap plugged into the master
		 location with the other end going to the
		 slave location on the next card in the
		 chain.
		 Additional cards may be chained by
		 linking from master to slave in the same
		 way, with the second card acting as
		 master to the third and so on."
    HELP =	"No inter-card strap is required when a
		 single card is installed.
		 The Chase EISA cards do not require to
		 be interlinked in this way and do not
		 need to be linked to any Chase AT cards
		 that are installed."

JUMPER(6) =	2
    NAME =	"LK4"
    JTYPE =	PAIRED
    VERTICAL =	YES
    REVERSE =	YES
    FACTORY =	LOC ( 2-1 ) 00
    COMMENTS =  "This link field can be used to select an
		 alternate I/O port base address for the
		 card. The card uses eight bytes of I/O
		 space starting at this location. All
		 Chase AT cards should use the same I/O
		 address."
    HELP =	"As shipped all Chase AT cards use the
		 I/O address 0x1F8. There should be no
		 needed to change this but if changes are
		 made then it will be necessary to
		 reconfigure the device driver software."

JUMPER(7) =	1
    NAME =	"LK5"
    JTYPE =	PAIRED
    VERTICAL =	YES
    REVERSE =	NO
    FACTORY =	LOC ( 1 ) 0
    COMMENTS =	"If a link is installed in this location
		 then the card will output a test message
		 on all ports at a speed of 9600 baud.
		 The card will not function normally with
		 this link installed and does not require
		 the operating system to be booted before
		 the test takes place."
    HELP =	"This test can be used to check the
		 cabling and function of terminals before
		 checking for possible problems with a
		 particular operating system."

JUMPER(8) =	1
    NAME =	"LK6"
    JTYPE =	PAIRED
    VERTICAL =	YES
    REVERSE =	NO
    FACTORY =	LOC ( 1 ) 0
    COMMENTS =  "This link is used to connect the host
		 computers +5V power supply to the 78 way
		 connector on the board in order to
		 supply specialist external adapters.
		 This link should not be installed with
		 the standard Chase adapters."
    HELP =	"Do not install this link unless you have
		 had explicit instructions to do so with
		 your external adapter."

JUMPER(9) =	1
    NAME =	"LK7"
    JTYPE =	PAIRED
    VERTICAL =	YES
    REVERSE =	NO
    FACTORY =	LOC ( 1 ) 0
    COMMENTS =  "This link is used to connect the host
		 computers +12V power supply to the 78
		 way connector on the board in order to
		 supply specialist external adapters.
		 This link should not be installed with
		 the standard Chase adapters."
    HELP =	"Do not install this link unless you have
		 had explicit instructions to do so with
		 your external adapter."

JUMPER(10) =	1
    NAME =	"LK8"
    JTYPE =	PAIRED
    VERTICAL =	YES
    REVERSE =	NO
    FACTORY =	LOC ( 1 ) 0
    COMMENTS =  "This link is used to connect the host
		 computers -12V power supply to the 78
		 way connector on the board in order to
		 supply specialist external adapters.
		 This link should not be installed with
		 the standard Chase adapters."
    HELP =	"Do not install this link unless you have
		 had explicit instructions to do so with
		 your external adapter."

JUMPER(11) =	2
    NAME =	"LK9"
    JTYPE =	INLINE
    VERTICAL =	NO
    REVERSE =	YES
    INITVAL =	LOC ( 2^3 ) 1
    FACTORY =	LOC ( 2^3 ) 1
    COMMENTS =  "The purpose of this link is to enable asynchronous 
		connunications."
    HELP =	"Do not remove this link."

JUMPER(12) =	1
    NAME =	"TESTL1"
    JTYPE =	PAIRED
    VERTICAL =	YES
    REVERSE =	NO
    INITVAL =	LOC ( 1 ) 1
    FACTORY =	LOC ( 1 ) 1
    COMMENTS =  "This jumper enables a factory test
		 requiring specialist equipment and
		 should never be removed."
    HELP =	"Do not remove this link."

GROUP = "Hardware resources used"
    TYPE =	"COM,ASY,MPX"
FUNCTION =	"Chase Acknowledge Interrupt (CAI)"
    COMMENTS =	"This is one of the two interrupts used
		 by the master ( or first ) card.
		 All Slave ( or subsequent ) cards do not
		 use interrupts and should set to NONE."
    HELP =	"As supplied the first card is configured
		 to use IRQ 10 for the CAI."
    CHOICE =	"IRQ 3"
	LINK
	    IRQ =	3
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(3) LOC(8-1) 00000001
    CHOICE =	"IRQ 4"
	LINK
	    IRQ =	4
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(3) LOC(8-1) 00000010
    CHOICE =	"IRQ 5"
	LINK
	    IRQ =	5
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(3) LOC(8-1) 00000100
    CHOICE =	"IRQ 7"
	LINK
	    IRQ =	7
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(3) LOC(8-1) 00001000
    CHOICE =	"IRQ 10"
	LINK
	    IRQ =	10
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(3) LOC(8-1) 00010000
    CHOICE =	"IRQ 11"
	LINK
	    IRQ =	11
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(3) LOC(8-1) 00100000
    CHOICE =	"IRQ 12"
	LINK
	    IRQ =	12
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(3) LOC(8-1) 01000000
    CHOICE =	"IRQ 15"
	LINK
	    IRQ =	15
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(3) LOC(8-1) 10000000
    CHOICE =	"NONE (slave cards)"
	DISABLE =	YES
	LINK
	    INIT =	JUMPER(3) LOC(8-1) 00000000

FUNCTION =	"Chase Completion Interrupt (CCI)"
    COMMENTS =	"This is the second of the two interrupts
		 used by the master ( or first ) card.
		 All Slave ( or subsequent ) cards do not
		 use interrupts and should set to NONE."
    HELP =	"As supplied the first card is configured
		 to use IRQ 15 for the CCI."
    CHOICE =	"IRQ 3"
	LINK
	    IRQ =	3
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(4) LOC(8-1) 00000001
    CHOICE =	"IRQ 4"
	LINK
	    IRQ =	4
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(4) LOC(8-1) 00000010
    CHOICE =	"IRQ 5"
	LINK
	    IRQ =	5
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(4) LOC(8-1) 00000100
    CHOICE =	"IRQ 7"
	LINK
	    IRQ =	7
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(4) LOC(8-1) 00001000
    CHOICE =	"IRQ 10"
	LINK
	    IRQ =	10
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(4) LOC(8-1) 00010000
    CHOICE =	"IRQ 11"
	LINK
	    IRQ =	11
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(4) LOC(8-1) 00100000
    CHOICE =	"IRQ 12"
	LINK
	    IRQ =	12
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(4) LOC(8-1) 01000000
    CHOICE =	"IRQ 15"
	LINK
	    IRQ =	15
		SHARE =	NO
		TRIGGER = EDGE
	    INIT =	JUMPER(4) LOC(8-1) 10000000
    CHOICE =	"NONE (slave cards)"
	DISABLE =	YES
	LINK
	    INIT =	JUMPER(4) LOC(8-1) 00000000

FUNCTION =	"DMA channel for Chase card"
    COMMENTS =	"Select a seperate DMA channel for each
		 card."
    HELP =	"As supplied the device driver will
		 expect the first card to use DMA channel
		 5. With additional cards using channels
		 6, 7, 0 in that order."
    CHOICE =	"DMA 5"
	LINK
	    DMA =	5
		SHARE =	NO
		TIMING = DEFAULT
	    INIT =	JUMPER(1) LOC (1-7) 0000100
	    INIT =	JUMPER(2) LOC (1-7) 0000100
    CHOICE =	"DMA 6"
	LINK
	    DMA =	6
		SHARE =	NO
		TIMING = DEFAULT
	    INIT =	JUMPER(1) LOC (1-7) 0000010
	    INIT =	JUMPER(2) LOC (1-7) 0000010
    CHOICE =	"DMA 7"
	LINK
	    DMA =	7
		SHARE =	NO
		TIMING = DEFAULT
	    INIT =	JUMPER(1) LOC (1-7) 0000001
	    INIT =	JUMPER(2) LOC (1-7) 0000001
    CHOICE =	"DMA 0"
	LINK
	    DMA =	0
		SHARE =	NO
		TIMING = DEFAULT
	    INIT =	JUMPER(1) LOC (1-7) 1000000
	    INIT =	JUMPER(2) LOC (1-7) 1000000

FUNCTION =	"Chase I/O address"
    COMMENTS =	"Select an IO address range that does not
		 conflict with any other devices.
		 All Chase AT cards should use the same
		 address range."
    HELP =	"As supplied the device driver will
		 expect the cards to use the address
		 range 1F8h-1FFh"
    CHOICE =	"1F8h-1FFh"
	LINK
	    PORT =	1F8h-1FFh
		SHARE =	YES
		SIZE = BYTE
	    INIT =	JUMPER(6) LOC(2-1) 00
    CHOICE =	"390h-397h"
	LINK
	    PORT =	390h-397h
		SHARE =	YES
		SIZE = BYTE
	    INIT =	JUMPER(6) LOC(2-1) 01
    CHOICE =	"3E0h-3E7h"
	LINK
	    PORT =	3E0h-3E7h
		SHARE =	YES
		SIZE = BYTE
	    INIT =	JUMPER(6) LOC(2-1) 10
    CHOICE =	"100h-107h"
	LINK
	    PORT =	100h-107h
		SHARE =	YES
		SIZE = BYTE
	    INIT =	JUMPER(6) LOC(2-1) 11

ENDGROUP