BOARD
 ID="CPQ4030"
 NAME="Compaq SMART-2/E Array Controller"
 MFR="Compaq"
 CATEGORY="MSD"
 SLOT=EISA
 LENGTH=330
 READID=YES
 AMPERAGE=2310
 BUSMASTER=200
 VERSION=0.01
 REV=0
 IOCHECK=INVALID
 DISABLE=UNSUPPORTED
 IOPORT(1)=0zCC0h
 IOPORT(2)=0zC84h
 IOPORT(4)=0zCA7h
 IOPORT(5)=0zC89h
 IOPORT(6)=0zCE0h
 IOPORT(7)=0zCE2h
 IOPORT(8)=0zC85h
 IOPORT(9)=0zCA6h

;Initial Setup
FUNCTION=""
SHOW=NO
TYPE=""
CHOICE=""
LINK
;INIT=IOPORT(4) LOC(7-0)11111110 ;Hard Code EPIC's memory decode rage to FE000000
INIT=IOPORT(2) LOC(3)0          ;This init disables EMB66
INIT=IOPORT(1) LOC(3)0          ;These 4 inits enable EPIC EISA Interrupts
INIT=IOPORT(6) LOC(6)1
INIT=IOPORT(7) LOC(6)1
INIT=IOPORT(5) LOC(0)1

INCLUDE="CPQ4030.OVL"
BEGINOVL

FUNCTION="Controller Order"
HELP="When adding a controller to a configured system, you can
either place it at the end of the controller order or reorder 
the controllers.  Reordering changes the current drive letter 
assignments for all drives on the system. To avoid changing 
the drive letter assignments when you add a controller to a 
configured system, place it at the end of the controller 
order and DO NOT CREATE A PRIMARY PARTITION on any of the 
added disks."
RESOURCE="CNTRORD",UNIQUE
CHOICE="First"
  SUBTYPE="MSD,DSKCTL;CTL1" LINK MEMBER="CNTRORD","1" SHARE=NO
CHOICE="Second"
  SUBTYPE="MSD,DSKCTL;CTL2" LINK MEMBER="CNTRORD","2" SHARE=NO
CHOICE="Third"
  SUBTYPE="MSD,DSKCTL;CTL3" LINK MEMBER="CNTRORD","3" SHARE=NO
CHOICE="Fourth"
  SUBTYPE="MSD,DSKCTL;CTL4" LINK MEMBER="CNTRORD","4" SHARE=NO
CHOICE="Fifth"
  SUBTYPE="MSD,DSKCTL;CTL5" LINK MEMBER="CNTRORD","5" SHARE=NO
CHOICE="Sixth"
  SUBTYPE="MSD,DSKCTL;CTL6" LINK MEMBER="CNTRORD","6" SHARE=NO
CHOICE="Seventh"
  SUBTYPE="MSD,DSKCTL;CTL7" LINK MEMBER="CNTRORD","7" SHARE=NO
CHOICE="Eighth"
  SUBTYPE="MSD,DSKCTL;CTL8" LINK MEMBER="CNTRORD","8" SHARE=NO
CHOICE="Ninth"
  SUBTYPE="MSD,DSKCTL;CTL9" LINK MEMBER="CNTRORD","9" SHARE=NO
CHOICE="Tenth"
  SUBTYPE="MSD,DSKCTL;CTL10" LINK MEMBER="CNTRORD","A" SHARE=NO
CHOICE="Eleventh"
  SUBTYPE="MSD,DSKCTL;CTL11" LINK MEMBER="CNTRORD","B" SHARE=NO
CHOICE="Twelfth"
  SUBTYPE="MSD,DSKCTL;CTL12" LINK MEMBER="CNTRORD","C" SHARE=NO
CHOICE="Thirteenth"
  SUBTYPE="MSD,DSKCTL;CTL13" LINK MEMBER="CNTRORD","D" SHARE=NO
CHOICE="Fourteenth"
  SUBTYPE="MSD,DSKCTL;CTL14" LINK MEMBER="CNTRORD","E" SHARE=NO
CHOICE="Fifteenth"
  SUBTYPE="MSD,DSKCTL;CTL15" LINK MEMBER="CNTRORD","F" SHARE=NO


FUNCTION="Interrupt"
TYPE="MSD,DSKCTL;BMIC"
CHOICE="Enabled"
LINK
IRQ=15|14|11|10
SHARE="DARRAY"
TRIGGER=LEVEL
INIT=IOPORT(1)LOC(7-4)1000|0100|0001|0010

FUNCTION="Option ROM"
HELP="The address of the Option ROM may be changed if it conflicts
with another board.  If there are multiple SMART-2/E Controllers in
the system, only one should have the Option ROM enabled."
RESOURCE="DAZROM",UNIQUE
CHOICE="Enabled"
 LINK
 MEMBER="DAZROM","ON" SHARE=NO
 SUBCHOICE
   LINK
   MEMORY=16K ADDRESS=0C8000h SIZE=BYTE DECODE=24 MEMTYPE=OTH
   INIT=IOPORT(9) LOC(1-0)01
 SUBCHOICE
   LINK
   MEMORY=16K ADDRESS=0D0000h SIZE=BYTE DECODE=24 MEMTYPE=OTH
   INIT=IOPORT(9) LOC(1-0)10
 SUBCHOICE
   LINK
   MEMORY=16K ADDRESS=0D8000h SIZE=BYTE DECODE=24 MEMTYPE=OTH
   INIT=IOPORT(9) LOC(1-0)11
CHOICE="Disabled"
 DISABLE=YES
 LINK
 INIT=IOPORT(9) LOC(1-0)00

; Function contains free-form controller id.
FUNCTION="Online Recovery Server Status"
TYPE="MSD,DSKCTL;CTLID"
HELP="This function indicates if this controller is able to partcipate
in Online Recovery. A primary controller controls the local storage device,
while a recovery controller is able to adopt a storage device from another
system which has had an online recovery event occur."
CHOICE="Disabled"
CHOICE="Primary"
CHOICE="Recovery"

FUNCTION="Drive Characteristics"
CHOICE="View with Compaq Array Configuration Utility"

FUNCTION=""                     ; LED Modes
SHOW=NO
CHOICE=""
LINK
INIT=IOPORT(1) LOC(1-0)11       ; Disable LED Interface Mode
INIT=IOPORT(8) LOC(3)0          ; This bit is "Don't care" when LEDs disabled
CHOICE=""
LINK
INIT=IOPORT(1) LOC(1-0)01       ; SystemPro LED Interface Mode
INIT=IOPORT(8) LOC(3)0          ; SystemPro LED Source Mode (Data Transfer Mode)
CHOICE=""
LINK
INIT=IOPORT(1) LOC(1-0)00       ; Other LED Interface Mode
INIT=IOPORT(8) LOC(3)1          ; Other LED Source Mode (Register Mode)

FUNCTION="SCSI Bus Speed"
SHOW=EXP
HELP="This function is for selecting the SCSI bus speed. However, the
selection is only valid when there are drives attached to the controller
and the drives have been configured with Compaq Array Configuration Utility"

CHOICE="Auto-detection"
CHOICE="Max Speed Possible"
CHOICE="SCSI-2 Compliant"
CHOICE="Asynchronous"

FUNCTION="Cache Size"                     ; EPIC memory
;SHOW=NO
CHOICE=""
LINK
INIT=IOPORT(4) LOC(7-0)11111110 ;Hard Code EPIC's memory decode rage to FE000000
CHOICE=""
LINK
INIT=IOPORT(4) LOC(7-0)11111000 ;Hard Code EPIC's memory decode rage to F8000000
FUNCTION="Firmware Revision"
CHOICE=""

ENDOVL