; EISA Configuration File for Computone IntelliPort AT 6/8/16 ; Revision History: ; 2/04/91 MAG Original Version ; 10/04/91 MAG Bug-fix: addresses below 1-meg were incorrect ; (were given as segments, not addresses) ; 10/19/91 MAG Derived from CTN0031: Firmware version 3.13b for ; IntelliPort AT6-SE supports some addresses in the E0000 address ; range (These addresses are not supported in other IntelliPort-AT ; firmware, hence a separate file) ; 12/2/91 MAG Bug-fix: DIP switch setting 00010001 yeilds ; (and has always yeilded) address fec000, not 124000. ; (note, fec000 may not be supported by the driver). ; 3/20/92 MAG Comments made more general: previous versions ; would not apply to all config utilities. ; 12/15/93 MAG Config Disk's Version number added to HELP ; BOARD ID = "CTN0036" NAME = "Computone IntelliPort AT6-SE" MFR = "Computone Corporation" CATEGORY = "COM" AMPERAGE = 2000 COMMENTS = "The Computone AT6-SE supports two synchronous and four asynchronous ports. This configuration file supports firmware version 3.13b and higher, which supports mapping the board to address E0000.\n\n The IntelliPort boards do not support automatic configuration. Use this configuration utility to select options and to view resulting switch and jumper settings." HELP = "Option/Configuration Disk, Version 2.06\n Select IRQ and address range.\n Then view switch & jumper settings for manually configuring the board." SWITCH(1) = 8 STYPE = dip NAME = "SW1" FACTORY = LOC(8-1) 00111000 JUMPER(1) = 6 JTYPE = paired NAME = "P6" REVERSE = yes LABEL = LOC(1 2 3 4 5 6) "3" "5" "10" "11" "12" "15" FACTORY = LOC(1-6) 000001 SOFTWARE(1) = "Drivers are available to support:\n SCO Xenix and Unix\n AT&T / Interactive Unix (3.2)\n UNIX System V release 4\n MSDOS, PCMOS\n The drivers are supplied on separate diskette. Refer to our manual as well as the manuals for your o/s for driver installation information.\n Please make note which interrupt you have selected; you will need this during driver installation." FUNCTION = "Computone IntelliPort AT6-SE" CONNECTION = "4 x RJ11 connectors for asynchronous ports.\n 2 x RJ45 (10-pin) connectors for synchronous ports.\n" TYPE = "COM" SUBFUNCTION = "Memory Address Range " COMMENTS= "Select the base address of this board. Select [help] for more advice." HELP= "First choose the general area of address space in which to configure the board. If you must specify the exact address within the area, edit or change resource." CHOICE = "14th Megabyte (within E00000 - EFFFFF)" COMBINE MEMORY = 16k ADDRESS = 0ecc000h | 0ea8000h | 0e8c000h | 0e64000h | 0e50000h | 0e24000h | 0e08000h MEMTYPE = oth SIZE = word DECODE = 24 INIT = SWITCH(1) LOC(8-1) 00111000 | 00110110 | 00110101 | 00110111 | 00110100 | 00110011 | 00110010 CHOICE = "13th Megabyte (within D00000 - DFFFFF)" COMBINE MEMORY = 16k ADDRESS = 0d8c000h | 0d50000h | 0d24000h | 0d08000h MEMTYPE = oth SIZE = word DECODE = 24 INIT = SWITCH(1) LOC(8-1) 00110001 | 00110000 | 00101111 | 00101110 CHOICE = "12th Megabyte (within C00000 - CFFFFF)" COMBINE MEMORY = 16k ADDRESS = 0c8c000h | 0c50000h | 0c24000h | 0c08000h MEMTYPE = oth SIZE = word DECODE = 24 INIT = SWITCH(1) LOC(8-1) 00101101 | 00101100 | 00101011 | 00101010 CHOICE = "15th Megabyte (within F00000 - FFFFFF)" COMBINE MEMORY = 16k ADDRESS = 0fcc000h | 0fa8000h | 0f8c000h | 0f64000h | 0f50000h | 0f24000h | 0f08000h | 0fec000h MEMTYPE = oth SIZE = word DECODE = 24 INIT = SWITCH(1) LOC(8-1) 00111111 | 00111101 | 00111100 | 00111110 | 00111011 | 00111010 | 00111001 | 00010001 CHOICE = "Below 1 Megabyte (within 00000 - FFFFF)" COMBINE MEMORY = 16k ADDRESS = 0c0000h | 0c4000h | 0c8000h | 0cc000h | 0d0000h | 0d4000h | 0d8000h | 0dc000h | 0ec000h | 0e8000h | 0e4000h | 0e0000h | 0a8000h | 0ac000h | 0b8000h | 0bc000h | 80000h | 84000h | 88000h | 8c000h MEMTYPE = oth SIZE = word DECODE = 24 INIT = SWITCH(1) LOC(8-1) 00001000 | 00001001 | 00001010 | 00001011 | 00001100 | 00001101 | 00001110 | 00001111 | 00010101 | 00010100 | 00010011 | 00010010 | 00000100 | 00000101 | 00000110 | 00000111 | 00000000 | 00000001 | 00000010 | 00000011 CHOICE = "8th through 11th Megabyte (within 800000 - BFFFFF)" COMBINE MEMORY = 16k ADDRESS = 0b50000h | 0b24000h | 0b08000h | 0a50000h | 0a24000h | 0a08000h | 0950000h | 0924000h | 0908000h | 0850000h | 0824000h | 0808000h MEMTYPE = oth SIZE = word DECODE = 24 INIT = SWITCH(1) LOC(8-1) 00101001 | 00101000 | 00100111 | 00100110 | 00100101 | 00100100 | 00100011 | 00100010 | 00100001 | 00100000 | 00011111 | 00011110 CHOICE = "Other addresses (within 100000 - 7FFFFF)" COMBINE MEMORY = 16k ADDRESS = 724000h | 708000h | 624000h | 608000h | 524000h | 508000h | 424000h | 408000h | 108000h MEMTYPE = oth SIZE = word DECODE = 24 INIT = SWITCH(1) LOC(8-1) 00011101 | 00011100 | 00011011 | 00011010 | 00011001 | 00011000 | 00010111 | 00010110 | 00010000 SUBFUNCTION = "Interrupt" CHOICE = "IRQ15" LINK IRQ = 15 SHARE = "CTN.IP" TRIGGER = EDGE INIT = JUMPER(1) LOC(1 2 3 4 5 6) 000001 CHOICE = "IRQ12" LINK IRQ = 12 SHARE = "CTN.IP" TRIGGER = EDGE INIT = JUMPER(1) LOC(1 2 3 4 5 6) 000010 CHOICE = "IRQ11" LINK IRQ = 11 SHARE = "CTN.IP" TRIGGER = EDGE INIT = JUMPER(1) LOC(1 2 3 4 5 6) 000100 CHOICE = "IRQ10" LINK IRQ = 10 SHARE = "CTN.IP" TRIGGER = EDGE INIT = JUMPER(1) LOC(1 2 3 4 5 6) 001000 CHOICE = "IRQ5" LINK IRQ = 5 SHARE = "CTN.IP" TRIGGER = EDGE INIT = JUMPER(1) LOC(1 2 3 4 5 6) 010000 CHOICE = "IRQ3" LINK IRQ = 3 SHARE = "CTN.IP" TRIGGER = EDGE INIT = JUMPER(1) LOC(1 2 3 4 5 6) 100000