BOARD
  ID = "DEL0001"
  NAME="Dell System(R) 425E(TM) System Board"
  MFR="Dell Computer Corporation"
  CATEGORY = "SYS"
  SLOT = EMB(0)
  READID = YES
  SIZING = 0
  SYSTEM
    NONVOLATILE = 8192
    AMPERAGE = 15000
    SLOT(1) = EISA   LENGTH = 341 LABEL="EXP1"
    SLOT(2) = EISA   LENGTH = 341 LABEL="EXP2" SKIRT=NO
    SLOT(3) = EISA   LENGTH = 341 LABEL="EXP3" SKIRT=NO
    SLOT(4) = EISA   LENGTH = 341 LABEL="EXP4"
    SLOT(5) = EISA   LENGTH = 341 LABEL="EXP5"
    SLOT(6) = EISA   LENGTH = 341 LABEL="EXP6"
    SLOT(7) = ISA16  LENGTH = 341 LABEL="EXP7"
    SLOT(8) = ISA16  LENGTH = 341 LABEL="EXP8"
    MEMORY = 256M  ADDRESS = 0  CACHE = YES  STEP = 32K

  ;--------------------------------
  ; Dell System Board Jumpers
  ;--------------------------------
JUMPER(1) = 1
  JTYPE = PAIRED
  NAME= "JM2"
  VERTICAL = YES
  LABEL = LOC(1) "MAINT JM2"
  INITVAL = LOC(1) 0
  FACTORY = LOC(1) 0
  COMMENTS = "Factory Test Jumper\n
	      Jumper JM2 is used during the manufacture of the Dell System
 425E to test the basic input/output system (BIOS) software.  Thereafter,
 its pins are left open (unjumpered).  Do not install a jumper plug on the
 JM2 pins unless instructed to do so by a Dell service technician."

  FUNCTION = "Factory Test Jumper"
    SHOW = NO
    CHOICE = "Normal"

JUMPER(3) = 2
  JTYPE = INLINE
  NAME= "JM1"
  VERTICAL = NO
  INITVAL = LOC(3^2 2^1) 10
  FACTORY = LOC(3^2 2^1) 10
  COMMENTS = "Monitor-Type Jumper\n
		Jumper JM1 indicates the primary display when both
 monochrome and CGA video cards are installed.  For a color monitor, 
 pins 2 and 3 are jumpered; for a monochrome monitor, pins 1 and 2 are 
 jumpered.  The function of jumper JM4 is better handled through the 
 System Setup program.  Use the \"Display\" category to select the 
 primary display in computer systems that have both monochrome and 
 color graphics adapter (CGA) video boards.  For all other computer
 systems, ignore this category."
  FUNCTION = "Monitor Type Jumper"
    SHOW = NO
    CHOICE = "Normal"

JUMPER(4) = 1
  JTYPE = PAIRED
  NAME= "J20"
  VERTICAL = YES
  LABEL = LOC(1) "RESET  J20"
  INITVAL = LOC(1) 0
  FACTORY = LOC(1) 0
  COMMENTS = "Factory Reset Jumper\n
	      Jumper J20 is normally open (unjumpered).  Trained, qualified
 technicians can use this jumper to reset the system when it does not
 reboot normally or respond to the keyboard.  Do not install a jumper plug
 on the J20 pins unless instructed to do so by a Dell service technician."

  FUNCTION = "Factory Reset Jumper"
    SHOW = NO
    CHOICE = "Normal"

JUMPER(2) = 4
  JTYPE = PAIRED
  NAME= "J26"
  VERTICAL = NO
  LABEL = LOC(4-1) "D" "C" "B" "A"
  FACTORY = LOC(4-1) 1111
  COMMENTS = "Memory Configuration Jumpers\n
	      Jumper J26 is used to indicate whether 1-MB or 2-MB single
 in-line memory modules (SIMMs) are installed in each of the four
 banks of SIMM sockets.  A jumper plug is installed for each bank containing
 1-MB SIMMs; no jumper plug is installed for each bank containing 2-MB 
 SIMMs.  A jumper has no effect if SIMMs are not installed in the 
 corresponding bank.  The factory setting for a bank with no SIMMs is 
 to have a jumper plug installed (jumpered) in case you later want 
 to add 1-MB SIMMs."

  INCLUDE = "DELSETUP.OVL"

GROUP = "Advanced Features"
  FUNCTION="BIOS Caching"
  COMMENTS="For better system performance, leave BIOS caching enabled unless
  	    told to disable it by a Dell service technician.\n"
    SHOW = EXP
    CHOICE="Enable"
    FREE
      MEMORY=64k ADDRESS=0F0000h MEMTYPE=OTHER WRITABLE=NO CACHE=YES
    CHOICE="Disable"
    FREE
      MEMORY=64k ADDRESS=0F0000h MEMTYPE=OTHER WRITABLE=NO CACHE=NO

  FUNCTION = "Fail-Safe Timer NMI"
    COMMENTS = "This option enables or disables the generation of a 
    		fail-safe timer non-maskable interrupt (NMI).\n"
    SHOW = EXP
    CHOICE = "Disable"
      DISABLE=YES
      FREE
	INIT = PORTADR(0461h) BYTE rrrrr0rr
    CHOICE = "Enable"
      FREE
	INIT = PORTADR(0461h) BYTE rrrrr1rr

  FUNCTION = "Bus-Master Timeout NMI"
    COMMENTS = "This option enables or disables the generation of a 
    		bus-master timeout non-maskable interrupt (NMI).\n"
    SHOW = EXP
    CHOICE = "Disable"
      DISABLE=YES
      FREE
	INIT = PORTADR(0461h) BYTE rrrr0rrr
    CHOICE = "Enable"
      FREE
	INIT = PORTADR(0461h) BYTE rrrr1rrr

  FUNCTION = "Software Generated NMI"
    COMMENTS = "This option enables or disables the generation of a 
    		software non-maskable interrupt (NMI).\n"
    SHOW = EXP
    CHOICE = "Disable"
      DISABLE=YES
      FREE
	INIT = PORTADR(0461h) BYTE rrrrrr0r
    CHOICE = "Enable"
      FREE
	INIT = PORTADR(0461h) BYTE rrrrrr1r

ENDGROUP