;
;*---  Dell GPX-1024 Graphics Performance Accelerator
;      ISA CFG Version 1.00
;
BOARD
  ID = "DELFC00"
  NAME = "Dell GPX-1024 Graphics Performance Accelerator"
  MFR = "DELL"
  CATEGORY = "VID"
  SLOT = ISA16
  LENGTH = 330
  DISABLE = UNSUPPORTED
  SKIRT = YES

JUMPER(1) = 2
  JTYPE = INLINE
  NAME = "W2"
  COMMENTS = "Factory Test Jumper\n
\n         Jumper W2 is used during the manufacture of the GPX-1024
 board; thereafter, a jumper plug is installed on pins 2 and 3 
 (jumpered).  Do not remove or move the jumper plug on the W2 pins 
 unless instructed to do so by a Dell service technician.\n
\n           OUT = 0,    IN = 1\n
\n     Jumper Plug Positions:
\n       1 (1-2)   -  0 = Reserved
\n       2 (2-3)   -  1 = Factory use only"
  VERTICAL = NO
  REVERSE = YES
  LABEL = LOC(1 2 3) "1" "2" "3"
  INITVAL = LOC(1^2 2^3) 01
  FACTORY = LOC(1^2 2^3) 01

JUMPER(2) = 8
  JTYPE = PAIRED
  NAME = "P4"
  COMMENTS = "Factory Test Jumper\n
\n         Jumper P4 is used during the manufacture of the GPX-1024
 board; thereafter, all of its pins are left open (unjumpered).  A
 jumper plug is stored on one pin of the pair labeled \"15,\" but the plug
 makes no electrical connection with another pin.  Do not install a
 jumper plug on any of the P4 pins unless instructed to do so by a
 Dell service technician.\n
\n        OUT = 0,    IN = 1\n
\n  Jumper Plug Positions:
\n    1   (2)   -  0
\n    2   (3)   -  0
\n    3   (4)   -  0
\n    4   (5)   -  0
\n    5   (10)  -  0
\n    6   (11)  -  0
\n    7   (12)  -  0
\n    8   (15)  -  0"
  VERTICAL = NO
  REVERSE = NO
  LABEL = LOC(8 7 6 5 4 3 2 1) "15" "12" "11" "10" "5" "4" "3" "2"

  INITVAL = LOC(8 7 6 5 4 3 2 1) 00000000
  FACTORY = LOC(8 7 6 5 4 3 2 1) 00000000

  SOFTWARE(1) = "
Software utilities supplied with the GPX-1024 board must be run to
 install a device driver, to set the graphics mode, to test the board,
 and to demonstrate the board's capabilites.  The device driver, which
 handles all communication between the computer and the graphics board,
 must be loaded before the GPX-1024 board will work.  The GPX-1024
 installation utility is run by INSTALL.EXE, a file on one of the diskettes
 supplied with the board.  A menu screen appears, and you are asked
 to specify the following configuration parameters:\n"

FUNCTION = "Dual Port RAM Mapping"
  COMMENTS = "
  The GPX-1024 board has a 4-KB dual-port RAM that needs to exist
  in the range from 0A0000h to 0DE0000h.  Select \"Change Resource\" from
  the Edit menu to change the dual-port RAM address."
  CHOICE = "Dual Port RAM Address"
    LINK
      MEMORY = 4K
        ADDRESS = 0CC000H | 0CE000H | 0C8000H | 0CA000H |
                  0D0000H | 0D2000H | 0D4000H | 0D6000H |
		  0D8000H | 0DA000H | 0DC000H | 0DE000H
        MEMTYPE = OTHER
        SIZE = WORD
      INIT = SOFTWARE(1)  "Buffer Address\tCC00" 
      			| "Buffer Address\tCE00" 
			| "Buffer Address\tC800" 
			| "Buffer Address\tCA00" 
			| "Buffer Address\tD000" 
			| "Buffer Address\tD200" 
			| "Buffer Address\tD400" 
			| "Buffer Address\tD600" 
			| "Buffer Address\tD800" 
			| "Buffer Address\tDA00" 
			| "Buffer Address\tDC00" 
			| "Buffer Address\tDE00"
    LINK
        PORT = 2B0H - 2BFH
    FREE
      INIT = SOFTWARE(1)  "Memory Bus Width 8"
      INIT = SOFTWARE(1) "I/O Bus Width\t8"