;  AEROFORMATION
;  Avenue pierre LATECOERE
;  BP 36
;  SERVICE : AEF/E-CC
;  31701 BLAGNAC Cedex
;  FRANCE
;
; (C)Copyright Aeroformation, 1991
;    All Rights Reserved.
; Author : Y.MOY,G.BARBE
; Date:   13 November 1991

BOARD
   ID       = "EMT2000"
   NAME     = "E/MASTER II-AT ThinLAN Interface Board"
   MFR      = "COGENT Data Technologies, inc."
   CATEGORY = "NET"
   SLOT     = ISA16
   COMMENTS = "The Cogent ThinLAN Interface board can be used in a server.\n
 It is only jumper configurable."

JUMPER(1) = 10
   JTYPE    = paired
   NAME     = "IRQ"
   REVERSE  = YES
   LABEL    = LOC(1-10) "15" "14" "12" "11" "10" "9" "7" "5" "4" "3"
   FACTORY  = LOC(1-10) 0000100000
   COMMENTS = "
 This jumper selects the IRQ used by the card.  The label of the
 jumper position corresponds to the IRQ used. "

JUMPER(2) = 5
   NAME     = "DMA DACK"
   JTYPE    = PAIRED
   REVERSE  = YES
   LABEL    = LOC(1-5) "7" "6" "5" "3" "0"
   FACTORY  = LOC(1-5) 00100
   COMMENTS = "
 This jumper selects the DMA channel used by the board.  The label on
 the jumper corresponds to the DMA channel used."


JUMPER(3) = 5
   NAME     = "DMA DRQ"
   JTYPE    = PAIRED
   REVERSE  = YES
   LABEL    = LOC(1-5) "7" "6" "5" "3" "0"
   FACTORY  = LOC(1-5) 00100
   COMMENTS = "
 This jumper selects the DMA channel used by the board.  The label on
 the jumper corresponds to the DMA channel used."


JUMPER(4) = 4
   NAME     = "I/O"
   JTYPE    = PAIRED
   VERTICAL = YES
   REVERSE  = YES
   LABEL    = LOC(1-4) "300h" "320h" "340h" "360h"
   FACTORY  = LOC(1-4) 1000
   COMMENTS = "
 This jumper specifies the I/O base address used by the board.  Follow
 the diagram below to set the jumper."

JUMPER(5) = 2
   NAME     = "ROM SIZE"
   JTYPE    = PAIRED
   VERTICAL = YES
   REVERSE  = YES
   LABEL    = LOC(1-2) "8K" "16K"
   FACTORY  = LOC(1-2) 01
   COMMENTS = "
 This jumper determines the ROM size (8K or 16K)."

JUMPER(6) = 5
   NAME     = "ROM BASE"
   JTYPE    = PAIRED
   VERTICAL = YES
   REVERSE = YES
   LABEL    = LOC(1-5) "C000h" "D000h" "D800h" "DC00h" "NO PROM"
   FACTORY  = LOC(1-5) 00001
   COMMENTS = "
 This jumper selects the ROM base address."


JUMPER(7) = 4
   NAME     = "LAN"
   JTYPE    = PAIRED
   VERTICAL = YES
   REVERSE = YES
   LABEL    = LOC(1-4) "A" "B" "C" "D"
   FACTORY  = LOC(1-4) 1000
   COMMENTS = "
 This jumper selects the LAN address."

JUMPER(8) = 2
   NAME     = "CABLE TYPE"
   JTYPE    = INLINE
   VERTICAL = YES
   FACTORY  = LOC(1^2 2^3) 10
   LABEL    = LOC(1^2 2^3) "BNC" "AUI"
   COMMENTS = "
 These jumpers set the type of the cable interface (BNC or AUI)."


SOFTWARE(1) = "
 Your network software may ask you for this data:"

FUNCTION = "EtherNet Adapter"
   TYPE = "NET"
   CONNECTION  = "One BNC connector and one DIX connector."
   SUBFUNCTION = "IRQ line"
      CHOICE = "IRQ 10"
         LINK
            IRQ = 10
            INIT = JUMPER(1) LOC(1-10) 0000100000
            INIT = SOFTWARE(1) "IRQ = 10"
      CHOICE = "IRQ 3"
         LINK
            IRQ = 3
            INIT = JUMPER(1) LOC(1-10) 0000000001
            INIT = SOFTWARE(1) "IRQ = 3"
      CHOICE = "IRQ 4"
         LINK
            IRQ = 4
            INIT = JUMPER(1) LOC(1-10) 0000000010
            INIT = SOFTWARE(1) "IRQ = 4"
      CHOICE = "IRQ 5"
         LINK
            IRQ = 5
            INIT = JUMPER(1) LOC(1-10) 0000000100
            INIT = SOFTWARE(1) "IRQ = 5"
      CHOICE = "IRQ 7"
         LINK
            IRQ = 7
            INIT = JUMPER(1) LOC(1-10) 0000001000
            INIT = SOFTWARE(1) "IRQ = 7"
      CHOICE = "IRQ 9"
         LINK
            IRQ = 9
            INIT = JUMPER(1) LOC(1-10) 0000010000
            INIT = SOFTWARE(1) "IRQ = 9"
      CHOICE = "IRQ 11"
         LINK
            IRQ = 11
            INIT = JUMPER(1) LOC(1-10) 0001000000
            INIT = SOFTWARE(1) "IRQ = 11"
      CHOICE = "IRQ 12"
         LINK
            IRQ = 12
            INIT = JUMPER(1) LOC(1-10) 0010000000
            INIT = SOFTWARE(1) "IRQ = 12"
      CHOICE = "IRQ 14"
         LINK
            IRQ = 14
            INIT = JUMPER(1) LOC(1-10) 0100000000
            INIT = SOFTWARE(1) "IRQ = 14"
      CHOICE = "IRQ 15"
         LINK
            IRQ = 15
            INIT = JUMPER(1) LOC(1-10) 1000000000
            INIT = SOFTWARE(1) "IRQ = 15"

   SUBFUNCTION = "DMA Channel"
      CHOICE = "DMA 5"
         LINK
            DMA  = 5
            INIT = JUMPER(2) LOC(1-5) 00100
            INIT = JUMPER(3) LOC(1-5) 00100
            INIT = SOFTWARE(1) "DMA = 5"
      CHOICE = "DMA 0"
         LINK
            DMA  = 0
            INIT = JUMPER(2) LOC(1-5) 00001
            INIT = JUMPER(3) LOC(1-5) 00001
            INIT = SOFTWARE(1) "DMA = 0"
      CHOICE = "DMA 3"
         LINK
            DMA  = 3
            INIT = JUMPER(2) LOC(1-5) 00010
            INIT = JUMPER(3) LOC(1-5) 00010
            INIT = SOFTWARE(1) "DMA = 3"
      CHOICE = "DMA 6"
         LINK
            DMA  = 6
            INIT = JUMPER(2) LOC(1-5) 01000
            INIT = JUMPER(3) LOC(1-5) 01000
            INIT = SOFTWARE(1) "DMA = 6"
      CHOICE = "DMA 7"
         LINK
            DMA  = 7
            INIT = JUMPER(2) LOC(1-5) 10000
            INIT = JUMPER(3) LOC(1-5) 10000
            INIT = SOFTWARE(1) "DMA = 7"


   SUBFUNCTION = "I/O Port Address"
      CHOICE = "300h"
         LINK
            PORT = 300h - 303h
            INIT = JUMPER(4) LOC(1-4) 1000
            INIT = SOFTWARE(1) "I/O Base = 300h-303h"
      CHOICE = "320h"
         LINK
            PORT = 320h - 323h
            INIT = JUMPER(4) LOC(1-4) 0100
            INIT = SOFTWARE(1) "I/O Base = 320h-323h"
      CHOICE = "340h"
         LINK
            PORT = 340h - 343h
            INIT = JUMPER(4) LOC(1-4) 0010
            INIT = SOFTWARE(1) "I/O Base = 340h-343h"
      CHOICE = "360h"
         LINK
            PORT = 360h - 363h
            INIT = JUMPER(4) LOC(1-4) 0001
            INIT = SOFTWARE(1) "I/O Base = 360h-363h"

   SUBFUNCTION = "Cable Type"
      HELP = "
 Select Internal (BNC connector) if you are using a ThinLAN cable.\n
 Select External (AUI connector) if you are using an AUI cable."
      CHOICE = "Internal (BNC connector)"
         FREE
            INIT = JUMPER(8) LOC(1^2 2^3) 10
      CHOICE = "External (AUI connector)"
         FREE
            INIT = JUMPER(8) LOC(1^2 2^3) 01

   SUBFUNCTION = "ROM Size and Address"
      HELP = "
The ROM size (if any) may be either 8K or 16K.
The base address can be C000, D000, D8000, DC00, or NOPROM."
      CHOICE = "16K and NO PROM"
         DISABLE = YES
         FREE
            INIT = JUMPER(5) LOC(1 2) 01
            INIT = JUMPER(6) LOC(1 - 5) 00001
            INIT = SOFTWARE(1) "ROM = 16K - NO PROM"
      CHOICE = "8K and C000"
         link
            MEMORY = 8K
            ADDRESS = 0C0000h
		WRITABLE = NO
		MEMTYPE  = OTH
            INIT = JUMPER(5) LOC(1-2) 10
            INIT = JUMPER(6) LOC(1-5) 10000
            INIT = SOFTWARE(1) "ROM = 8K at C000"
      CHOICE = "8K and D000h"
         link
            MEMORY = 8K
            ADDRESS = 0D0000h 
		WRITABLE = NO
		MEMTYPE  = OTH
            INIT = JUMPER(5) LOC(1-2) 10
            INIT = JUMPER(6) LOC(1 - 5) 01000
            INIT = SOFTWARE(1) "ROM = 8K at D000"
      CHOICE = "8K and D800h"
         link
            MEMORY = 8K
            ADDRESS = 0D8000h 
		WRITABLE = NO
		MEMTYPE  = OTH
            INIT = JUMPER(5) LOC(1-2) 10
            INIT = JUMPER(6) LOC(1 - 5) 00100
            INIT = SOFTWARE(1) "ROM = 8K at D800"
      CHOICE = "8K and DC00h"
         link
            MEMORY = 8K
            ADDRESS = 0DC000h 
		WRITABLE = NO
		MEMTYPE  = OTH
            INIT = JUMPER(5) LOC(1-2) 10
            INIT = JUMPER(6) LOC(1 - 5) 00010
            INIT = SOFTWARE(1) "ROM = 8K at DC00"
      CHOICE = "8K and NO PROM"
         DISABLE = YES
         link
            INIT = JUMPER(5) LOC(1-2) 10
            INIT = JUMPER(6) LOC(1 - 5) 00001
            INIT = SOFTWARE(1) "ROM = 8K - NO PROM"

      CHOICE = "16K and C000h"
         link
            MEMORY = 16K
            ADDRESS = 0C0000h 
		WRITABLE = NO
		MEMTYPE  = OTH
            INIT = JUMPER(5) LOC(1 2) 01
            INIT = JUMPER(6) LOC(1 - 5) 10000
            INIT = SOFTWARE(1) "ROM = 16K at C000"
      CHOICE = "16K and D000h"
         link
            MEMORY = 16K
            ADDRESS = 0D0000h 
		WRITABLE = NO
		MEMTYPE  = OTH
            INIT = JUMPER(5) LOC(1 2) 01
            INIT = JUMPER(6) LOC(1 - 5) 01000
            INIT = SOFTWARE(1) "ROM = 16K at D000"
      CHOICE = "16K and D800h"
         link
            MEMORY = 16K
            ADDRESS = 0D8000h 
		WRITABLE = NO
		MEMTYPE  = OTH
            INIT = JUMPER(5) LOC(1 2) 01
            INIT = JUMPER(6) LOC(1 - 5) 00100
            INIT = SOFTWARE(1) "ROM = 16K at D800"
      CHOICE = "16K and DC00h"
         link
            MEMORY = 16K
            ADDRESS = 0DC000h 
		WRITABLE = NO
		MEMTYPE  = OTH
            INIT = JUMPER(5) LOC(1 2) 01
            INIT = JUMPER(6) LOC(1 - 5) 00010
            INIT = SOFTWARE(1) "ROM = 16K at DC00"

   SUBFUNCTION = "LAN address"
      HELP = "
The LAN address, in the range A-D."
      CHOICE = "A"
         FREE
            INIT = JUMPER(7) LOC(1-4) 1000
      CHOICE = "B"
         FREE
            INIT = JUMPER(7) LOC(1-4) 0100
      CHOICE = "C"
         FREE
            INIT = JUMPER(7) LOC(1-4) 0010
      CHOICE = "D"
         FREE
            INIT = JUMPER(7) LOC(1-4) 0001