;
; (C)Copyright Hewlett-Packard Co., 1989-1990
;    All Rights Reserved.
;

BOARD
   ID       = "hwp1830"
   NAME     = "HP EtherTwist PC Adapter Card 16 (27247A)"
   MFR      = "Hewlett-Packard Co."
   CATEGORY = "NET"
   SLOT     = ISA16
   COMMENTS = "The HP EtherTwist PC Adapter Card 16 is a 16-bit Type
              10BASE-T compatible local area networking card."

SWITCH(1) = 4
   NAME = "I/O Base, Link Beat"
   STYPE = DIP
   REVERSE = YES
   FACTORY = LOC(4-1) 1001
   COMMENTS = "Switches 1 through 3 select the I/O Base Address,\n
               switch 4 is the Link Beat enable/disable switch.\n
               NOTE: 'off' in the diagram below corresponds to
                     'OPEN' on card switches."





SOFTWARE(1) = "
 Your network software may ask you for this data:"

FUNCTION = "EtherTwist PC Adapter Card 16 (HP27247A)"
   TYPE = "NET"
   CONNECTION  = "One modular 8-pin LAN connector, and\n
                  one modular 6-pin phone connector"

   SUBFUNCTION = "I/O Base Address"
      CHOICE = "300h"
         LINK
            INIT = SWITCH(1) LOC(1-3) 100
            INIT = SOFTWARE(1) "I/O Base=300h"
            PORT = 300h
      CHOICE = "340h"
         LINK
            INIT = SWITCH(1) LOC(1-3) 110
            INIT = SOFTWARE(1) "I/O Base=340h"
            PORT = 340h
      CHOICE = "240h"
         LINK
            INIT = SWITCH(1) LOC(1-3) 001
            INIT = SOFTWARE(1) "I/O Base=240h"
            PORT = 240h
      CHOICE = "200h"
         LINK
            INIT = SWITCH(1) LOC(1-3) 000
            INIT = SOFTWARE(1) "I/O Base=200h"
            PORT = 200h
      CHOICE = "280h - Don't use with Novell Netware"
         LINK
            INIT = SWITCH(1) LOC(1-3) 010
            INIT = SOFTWARE(1) "I/O Base=280h"
            PORT = 280h
      CHOICE = "2C0h - Don't use with Novell Netware"
         LINK
            INIT = SWITCH(1) LOC(1-3) 011
            INIT = SOFTWARE(1) "I/O Base=2C0h"
            PORT = 2C0h
      CHOICE = "320h - Don't use with Novell Netware or HP Vectra CS"
         LINK
            INIT = SWITCH(1) LOC(1-3) 101
            INIT = SOFTWARE(1) "I/O Base=320h"
            PORT = 320h

   SUBFUNCTION = "Link Beat"
      CHOICE = "Enabled"
         LINK
            INIT = SWITCH(1) LOC(4) 1
            INIT = SOFTWARE(1) "Link Beat Enabled"
      CHOICE = "Disabled"
         LINK
            INIT = SWITCH(1) LOC(4) 0
            INIT = SOFTWARE(1) "Link Beat Disabled"

   SUBFUNCTION = "Interrupt Channel (IRQ)"
      CHOICE = "3"
         LINK
            INIT = Software(1) "IRQ=3"
            IRQ = 3
      CHOICE = "4"
         LINK
            INIT = Software(1) "IRQ=4"
            IRQ = 4
      CHOICE = "5"
         LINK
            INIT = Software(1) "IRQ=5"
            IRQ = 5
      CHOICE = "7"
         LINK
            INIT = Software(1) "IRQ=7"
            IRQ = 7