;
; Hewlett-Packard EtherTwist Adapter Card/16 Version 1.01
; Configuration file version 1.02
; !HWP1831.CFG  10-03-1991
;
; (C)Copyright Hewlett-Packard Co., 1989-1991
;    All Rights Reserved.
;

BOARD
   ID       = "hwp1831"
   NAME     = "HP EtherTwist Adapter Card/16 (27247-60002)"
   MFR      = "Hewlett-Packard Co."
   CATEGORY = "NET"
   SLOT     = ISA16
   LENGTH   = 220
   COMMENTS = "The HP EtherTwist PC Adapter Card 16 is a 16-bit Type
              10BASE-T compatible local area networking card."

SWITCH(1) = 4
   NAME = "I/O Base, Link Beat"
   STYPE = DIP
   REVERSE = YES
   FACTORY = LOC(4-1) 1001
   COMMENTS = "Switches 1 through 3 select the I/O Base Address,\n
               switch 4 is the Link Beat enable/disable switch.\n
               NOTE: 'off' in the diagram below corresponds to
                     'OPEN' on card switches."


JUMPER(1) = 2
   NAME     = "IOCHRDY W1"
   JTYPE    = INLINE
   VERTICAL = YES
   REVERSE  = YES
   LABEL    = LOC(1^2 2^3) "T1" "T2"
   FACTORY  = LOC(1^2 2^3) 10
   INITVAL  = LOC(1^2 2^3) 10
   COMMENTS = "
 This jumper may be used to adjust the timing of the IOCHRDY signal coming from
 the adapter card. This allows the adapter card to be used in PCs that do not
 adhere to the ISA Specification timing requirements for IOCHRDY. Operation
 with the jumper in the T2 position should never be required on EISA standard
 PCs. Leave the jumper in the T1 position. Refer to the adapter card 
 installation guide for further details."

SOFTWARE(1) = "
 Your network software may ask you for this data:"

FUNCTION = "EtherTwist Adapter Card/16 (27247-60002)"
   TYPE = "NET"
   CONNECTION  = "One modular 8-pin LAN connector, and\n
                  one modular 6-pin phone connector"

   SUBFUNCTION = "I/O Base Address"
      CHOICE = "300h"
         LINK
            INIT = SWITCH(1) LOC(1-3) 100
            INIT = SOFTWARE(1) "I/O Base=300h"
            PORT = 300h
      CHOICE = "340h"
         LINK
            INIT = SWITCH(1) LOC(1-3) 110
            INIT = SOFTWARE(1) "I/O Base=340h"
            PORT = 340h
      CHOICE = "240h"
         LINK
            INIT = SWITCH(1) LOC(1-3) 001
            INIT = SOFTWARE(1) "I/O Base=240h"
            PORT = 240h
      CHOICE = "200h"
         LINK
            INIT = SWITCH(1) LOC(1-3) 000
            INIT = SOFTWARE(1) "I/O Base=200h"
            PORT = 200h
      CHOICE = "280h - Don't use with Novell Netware"
         LINK
            INIT = SWITCH(1) LOC(1-3) 010
            INIT = SOFTWARE(1) "I/O Base=280h"
            PORT = 280h
      CHOICE = "2C0h - Don't use with Novell Netware"
         LINK
            INIT = SWITCH(1) LOC(1-3) 011
            INIT = SOFTWARE(1) "I/O Base=2C0h"
            PORT = 2C0h
      CHOICE = "320h - Don't use with Novell Netware or HP Vectra CS"
         LINK
            INIT = SWITCH(1) LOC(1-3) 101
            INIT = SOFTWARE(1) "I/O Base=320h"
            PORT = 320h

   SUBFUNCTION = "Link Beat"
      CHOICE = "Enabled"
         LINK
            INIT = SWITCH(1) LOC(4) 1
            INIT = SOFTWARE(1) "Link Beat Enabled"
      CHOICE = "Disabled"
         LINK
            INIT = SWITCH(1) LOC(4) 0
            INIT = SOFTWARE(1) "Link Beat Disabled"

   SUBFUNCTION = "Interrupt Channel (IRQ)"
      CHOICE = "3"
         LINK
            INIT = Software(1) "IRQ=3"
            IRQ = 3
      CHOICE = "4"
         LINK
            INIT = Software(1) "IRQ=4"
            IRQ = 4
      CHOICE = "5"
         LINK
            INIT = Software(1) "IRQ=5"
            IRQ = 5
      CHOICE = "7"
         LINK
            INIT = Software(1) "IRQ=7"
            IRQ = 7
      CHOICE = "10"
         LINK
            INIT = Software(1) "IRQ=10"
            IRQ = 10
      CHOICE = "11"
         LINK
            INIT = Software(1) "IRQ=11"
            IRQ = 11