BOARD
	ID = "HWPC081"
	NAME = "HP Netserver LC System Board (CFG v1.08S)"
	MFR = "Hewlett-Packard Co."
	CATEGORY = "SYS"
	AMPERAGE = 17000
	SLOT=EMB(0)
	READID=YES
	COMMENTS = ""
	HELP=""

SYSTEM
	NONVOLATILE=4096		;4096 is reserved for PCI
	SLOT(0)=EISA(0)	LABEL="System"
	SLOT(1)=EISA(11),"ADP7770" LABEL="Embedded" BUSMASTER=YES
	SLOT(2)=EISA(5) LABEL="Slot 5"
		LENGTH=341
		BUSMASTER=YES
	SLOT(3)=EISA(4) LABEL="Slot 4"
		LENGTH=341
		BUSMASTER=YES
	SLOT(4)=EISA(3) LABEL="Slot 3"
		LENGTH=341
		BUSMASTER=YES
	SLOT(5)=EISA(2) LABEL="Slot 2"
		LENGTH=341
		BUSMASTER=YES
	SLOT(6)=EISA(1) LABEL="Slot 1"
		LENGTH=341
		BUSMASTER=YES

SWITCH(1)=1
	NAME="FLASH WRITE ENABLE"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "1"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="1 ON  = BIOS is unlocked (can be updated).
		\n1 OFF = BIOS is locked (cannot be updated)."

SWITCH(2)=1
	NAME="BOOT BLOCK DISABLE"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "2"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="2 ON  = BIOS Boot Block is Disabled.
		\n2 OFF = BIOS Boot Block is Enabled."


SWITCH(3)=1
	NAME="CONFIG VALID"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "3"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="3 ON  = Configuration information is preserved.
		\n3 OFF = Configuration information is cleared."

SWITCH(4)=1
	NAME="CONFIG UNLOCK"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "4"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="4 ON  = Configuration information is unlocked.
		\n4 OFF = Configuration information is locked."

SWITCH(5)=1
	NAME="PASSWORD ENABLE"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "5"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="5 ON  = Password is preserved and enabled.
		\n5 OFF = Password is erased and disabled."

SWITCH(6)=1
	NAME="SMI ENABLE"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "6"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="6 ON  = SMI enabled.
		\n6 OFF = SMI disabled."

SWITCH(7)=1
	NAME="I/O CTRL ENABLE"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "7"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="7 ON  = System board I/O controller enabled.
		\n        You must enable this switch in order to use any
		\n        of the on board peripheral devices.
		\n7 OFF = System board I/O controller disabled."

SWITCH(8)=1
	NAME="VIDEO ENABLE"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "8"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="8 ON  = System board VGA controller enabled.
		\n        You must enable this switch in order to use the
		\n        system board VGA controller.
		\n8 OFF = System board VGA controller disabled."

include = "HWPC071.OVL"

;********************
;* EISA NMI Control *
;********************

IOPORT(1) = 461h 		;EISA Extended NMI Control Register:
    SIZE = BYTE       		; bit 1 - Software NMI enable
    INITVAL = 0000x0x0		; bit 3 - bus timeout NMI enable

FUNCTION = "EISA NMI Control"
SHOW=EXP
  HELP = "
    EISA Non-maskable interrupts are controlled here.  When the Software
    NMI Generation Port (462h) is enabled, any output to that port causes
    an NMI."

  SUBFUNCTION = "Software NMI"
    CHOICE = "Enabled"	FREE INIT = IOPORT(1) LOC(1) 1
    CHOICE = "Disabled"	FREE INIT = IOPORT(1) LOC(1) 0

FUNCTION = "32-bit Bus Timeout NMI"
    SHOW=NO
    CHOICE = "Disabled"	FREE INIT = IOPORT(1) LOC(3) 0

FUNCTION="PCI Memory Region" TYPE = "MEM" SHOW=NO
    CHOICE="Reserved" 
    SUBTYPE="CMOS=4D03E0,CMOS=4EFC03"	; F8000000
        FREE MEMORY=64M ADDRESS=3968M MEMTYPE=VIR
        FREE MEMORY=64M ADDRESS=4032M MEMTYPE=VIR

;**************************
;* SYSTEM BOARD RESOURCES *
;**************************

GROUP = "Basic Main Board Functions"
  TYPE = "SYS"

FUNCTION = "TIMER"
  TYPE = "HP_PC,NAME=NETSERVER LC,SPU_NUM=41"
  SHOW = NO
  COMMENTS = "Reserves IRQ, DMA and other resources"
  HELP = "Help field for system board resources"
  CHOICE = "Reserved"
    FREE
      IRQ = 0
        TRIGGER = EDGE

FUNCTION = "Keyboard"
  SHOW = NO
  TYPE = "KEY"
  CHOICE = "101 Key"
    SUBTYPE = "101"
    LINK
      IRQ = 1
        TRIGGER = EDGE
      PORT = 60H
      PORT = 64H

FUNCTION = "Real-time Clock"
  SHOW = NO
  CHOICE = "Reserved"
    FREE
      IRQ = 8
        TRIGGER = EDGE
      PORT = 70H - 71H

FUNCTION = "Platform"
  SHOW = NO
  CHOICE = "Eval"
  ; No resources

FUNCTION = "Chip Set"
  SHOW = NO
  CHOICE = "82C430 PCI"
    LINK
      PORT = 0CF8h-0CFAh

FUNCTION = "Peripheral Controller"
  SHOW = NO
  CHOICE = "ESC"


ENDGROUP