;
;   Intel 486(tm) SX(tm) 82350DT EISA Board
;	Version:        2.0 (Preliminary)
;       Date:           5/20/91
;
;******************************************************************************

BOARD
    ID="INT0031"
    NAME="Intel 486 SX 82350DT EISA Board"
    MFR="INTEL FOLSOM"
    CATEGORY="SYS"
    SLOT=EMB(0)
    READID = YES

SYSTEM
    NONVOLATILE = 7680		;8192-512=7680 : 512 is for Phoenix BIOS reserve area.
    SLOT(1) = EISA
    SLOT(2) = EISA
    SLOT(3) = EISA
    SLOT(4) = EISA
    SLOT(5) = EISA
    SLOT(6) = EISA

    MEMORY = 640K   ADDRESS = 0K        CACHE = YES  STEP = 16K  ; Base memory
    MEMORY = 128K   ADDRESS = 640K	CACHE = NO		 ; Video Ram
    MEMORY = 256K   ADDRESS = 768K	CACHE = YES  STEP = 16K  ; Video/Exp ROM/Sys. BIOS
    MEMORY = 4095M  ADDRESS = 1M        CACHE = YES  STEP = 16K	 ; Ext. memory


;------------------------------------------------------------------------------
;                              Declare jumpers                                 
;------------------------------------------------------------------------------

JUMPER  ( 1) = 1
    NAME     = "J1: "
    JTYPE    = PAIRED
    VERTICAL = NO
    REVERSE  = NO
    INITVAL  = LOC (1) 1
    FACTORY  = LOC (1) 1
    COMMENTS = "I/O RECOVERY - DO NOT REMOVE THIS JUMPER: This signal 
                controls the delay between back to back ISA 8- and 16-bit 
                I/O cycles from the CPU."

JUMPER  ( 6) = 1 
    NAME     = "J6: "
    JTYPE    = PAIRED
    VERTICAL = YES
    REVERSE  = NO
    FACTORY  = LOC (1) 1    
    COMMENTS = "MONITOR TYPE:  closed = Color Monitor
       \n                      open   = Monochrome Monitor
              \nThis setting must reflect the selection in the AT SETUP window."

JUMPER  (25) = 2
    NAME     = "J25: "
    JTYPE    = PAIRED
    VERTICAL = YES
    REVERSE  = YES
    LABEL    = LOC (1 2) "DS0" "DS1"
    FACTORY  = LOC (1 2)  00  
    COMMENTS = "DRIVE SELECT: closed = 3.5 PS/2 Compatible drives
      \n                      open   = 5.25 or 3.5 AT compatible drives 
              \nThese settings must reflect the selections in the AT SETUP window."

JUMPER  (31) = 1 
    NAME     = "J31: "
    JTYPE    = TRIPOLE
    VERTICAL = YES
    REVERSE  = NO
    INITVAL  = LOC (1) 0
    FACTORY  = LOC (1) 0   
    COMMENTS = "BIOS FLASH MEMORY VPP: jumper in left  = +5V
      \n                               jumper in right = +12V"

JUMPER  (39) = 1
    NAME     = "J39: "
    JTYPE    = PAIRED
    VERTICAL = NO
    REVERSE  = NO
    INITVAL  = LOC (1) 0
    FACTORY  = LOC (1) 0
    COMMENTS = "SYSTEM BUS POSTED WRITE:  closed = Enabled
      \n                                  open   = Disabled"


;------------------------------------------------------------------------------
;                                 System Memory
;------------------------------------------------------------------------------

GROUP = "System Main Memory"

FUNCTION = "Base Memory"
    TYPE = "MEM"
    CHOICE = "640K";
	FREE
	  MEMORY = 640K  
	     ADDRESS = 0K
	     WRITABLE = YES
	     MEMTYPE = SYS
	     CACHE = YES
 
FUNCTION = "Extended  Memory"
    TYPE = "MEM"
    HELP = "The amount of installed RAM for use as extended memory is
            user-selectable.  Please refer to the ECU documentation to 
            find the appropriate menu option to 'change resources'."
    CHOICE = "You Choose: 1M - 64M"		 
	FREE					  
	  MEMORY = 1M - 64M STEP = 1M           
	     ADDRESS = 1M
	     WRITABLE = YES
	     MEMTYPE = SYS
	     CACHE = YES
ENDGROUP

;------------------------------------------------------------------------------
;                            Integrated Peripherals 
;------------------------------------------------------------------------------

GROUP = "Integrated Peripheral"

FUNCTION = "Integrated Parallel Interface"
    TYPE = "PAR"
    CHOICE = "Integrated Parallel Interface:  LPT1 - Edge Triggered"
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000010	; Parallel config. register 0C2h
	INIT = PORTADR(023h) BYTE rrrr0000	; Edge, AT mode, LPT1

	PORT = 03BCh-03BFh
	  SHARE = NO
	  SIZE = BYTE
	IRQ = 7
	  SHARE = NO

    CHOICE = "Integrated Parallel Interface:  LPT2 - Edge Triggered"
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000010	; Parallel config. register 0C2h
	INIT = PORTADR(023h) BYTE rrrr0001	; Edge, AT mode, LPT2

	PORT = 0378h-037Fh
	  SHARE = NO
	  SIZE = BYTE
	IRQ = 5
	  SHARE = NO

    CHOICE = "Integrated Parallel Interface:  LPT3 - Edge Triggered"
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000010	; Parallel config. register 0C2h
	INIT = PORTADR(023h) BYTE rrrr0010	; Edge, AT mode, LPT3

	PORT = 0278h-027Fh
	  SHARE = NO
	  SIZE = BYTE
	IRQ = 5
	  SHARE = NO

    CHOICE = "Integrated Parallel Interface:  Disabled"
      DISABLE = YES
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000010	; Parallel config. register 0C2h
	INIT = PORTADR(023h) BYTE rrrrrr11	; parallel disable

    CHOICE = "Integrated Parallel Interface:  LPT1 - level Triggered"
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000010	; Parallel config. register 0C2h
	INIT = PORTADR(023h) BYTE rrrr1100	; level, bi-dir, LPT1

	PORT = 03BCh-03BFh
	  SHARE = NO
	  SIZE = BYTE
	IRQ = 7
	  SHARE = YES
	  TRIGGER = LEVEL

    CHOICE = "Integrated Parallel Interface:  LPT2 - Level Triggered"
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000010	; Parallel config. register
	INIT = PORTADR(023h) BYTE rrrr1101	; level, bi-dir, LPT2

	PORT = 0378h-037Fh
	  SHARE = NO
	  SIZE = BYTE
	IRQ = 5
	    SHARE = YES
	    TRIGGER = LEVEL

    CHOICE = "Integrated Parallel Interface:  LPT3 - Level Triggered"
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000010	; Parallel config. register
	INIT = PORTADR(023h) BYTE rrrr1110	; level, bi-dir, LPT3

	PORT = 0278h-027Fh
	  SHARE = NO
	  SIZE = BYTE
	IRQ = 5
	    SHARE = YES
	    TRIGGER = LEVEL


  FUNCTION = "Integrated Serial Interface"
    TYPE = "COM"
    CHOICE = "Integrated Serial Interface:  COM1 - Edge Triggered"
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000011	; Serial Config Reg. A 0C3h
	INIT = PORTADR(023h) BYTE rr00rr10	; com1, port A enable

	PORT = 03F8h-03FFh
	  SHARE = NO
	  SIZE = BYTE
        IRQ = 4
          SHARE = NO
	  INIT = PORTADR(022h) BYTE 11000101	; Serial Config Reg. B 0C5h
	  INIT = PORTADR(023h) BYTE rr00rrr0	; IRQ 4, edge trigger

    CHOICE = "Integrated Serial Interface:  COM2 - Edge Triggered"
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000011	; Serial Config Reg. A 0C3h
	INIT = PORTADR(023h) BYTE rr01rr10	; com2, port A enable

	PORT = 02F8h-02FFh
	  SHARE = NO
	  SIZE = BYTE
        IRQ = 3
          SHARE = NO
	  INIT = PORTADR(022h) BYTE 11000101	; Serial Config Reg. B 0C5h
	  INIT = PORTADR(023h) BYTE rr01rrr0	; IRQ 3, edge trigger
 
   CHOICE = "Integrated Serial Interface:  Disabled"
      DISABLE = YES
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000011	; Serial config. reg.A 0C3h
	INIT = PORTADR(023h) BYTE rrrrrr11	; Disable port A and B

   CHOICE = "Integrated Serial Interface:  COM1 - Level Triggered"
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000011	; Serial Config Reg. A 0C3h
	INIT = PORTADR(023h) BYTE rr00rr10	; com1, port A enable

	PORT = 03F8h-03FFh
	  SHARE = NO
	  SIZE = BYTE
	IRQ = 4
	  SHARE = YES
	  INIT = PORTADR(022h) BYTE 11000101	; Serial Config Reg. B 0C5h
	  INIT = PORTADR(023h) BYTE rr00rrr1	; IRQ 4, level trigger

    CHOICE = "Integrated Serial Interface:  COM2 - Level Triggered"
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000011	; Serial Config Reg. A 0C3h
	INIT = PORTADR(023h) BYTE rr01rr10	; com2, port A enable

	PORT = 02F8h-02FFh
	  SHARE = NO
	  SIZE = BYTE
	IRQ = 3
	  SHARE = YES
	  INIT = PORTADR(022h) BYTE 11000101	; Serial Config Reg. B 0C5h
	  INIT = PORTADR(023h) BYTE rr01rrr1	; IRQ 3, level trigger


FUNCTION = "Mouse"
    TYPE = "PTR"	

    CHOICE = "Mouse:  Enabled"
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000001	; peripheral reg.B 0C1h
	INIT = PORTADR(023h) BYTE 11rrrrrr	; Level mode, interrupt enable
        IRQ = 12
	  SHARE = YES	

    CHOICE = "Mouse:  Disabled"
      DISABLE = YES
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000001	; peripheral reg.B 0C1h
	INIT = PORTADR(023h) BYTE r0rrrrrr	; interrupt disable


FUNCTION = "Integrated Floppy Controller"
    TYPE = "MSD,FPYCTL"
    CHOICE = "Integrated Floppy Controller:  Enabled"
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000100	; FDC config. register 0C4h
	INIT = PORTADR(023h) BYTE rrrrrr10	; XD buf.en, ext reg en,pri.adr

	INIT = PORTADR(022h) BYTE 11000000	; peripheral enable reg.A 0C0h
	INIT = PORTADR(023h) BYTE rrrr1rrr	; enable fdc

	PORT = 3F0H-3F5H
	  SIZE = BYTE
	  SHARE = NO
	PORT = 3F7H
	  SIZE = BYTE
	  SHARE = YES
        DMA = 2
          SHARE = NO
          SIZE = BYTE
          TIMING = TYPEA
        IRQ = 6
          SHARE = NO
          TRIGGER = EDGE

    CHOICE = "Integrated Floppy Controller:  Disabled"
      DISABLE = YES
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000000	; peripheral enable reg.A 0C0h
	INIT = PORTADR(023h) BYTE rrrr0rrr	; disable fdc

FUNCTION = "Integrated IDE Hard Disk Controller"
    TYPE = "MSD,DSKDTL"

    CHOICE = "Integrated IDE Hard Disk Controller:  Disabled"
      DISABLE = YES
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E

	INIT = PORTADR(022h) BYTE 11000001	; Peripheral enable reg.B 0C1h
	INIT = PORTADR(023h) BYTE rrrrrr00	; Disable GPCS0# and GPCS1#

	INIT = PORTADR(022h) BYTE 11000100	; FDC config. register 0C4h
	INIT = PORTADR(023h) BYTE rrrrr0rr	; XD buffer disable

    CHOICE = "Integrated IDE Hard Disk Controller:  Enabled"
      FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000010	; Enable LIO.E
						; GPCS0 = 1F0h - 1F7h
	INIT = PORTADR(022h) BYTE 11010100	; GPCS0# low address 0D4h
	INIT = PORTADR(023h) BYTE 11110000	; A7-A0 = FXh

	INIT = PORTADR(022h) BYTE 11011000	; GPCS0# high address 0D8h
	INIT = PORTADR(023h) BYTE 00000001	; A15-A80 = 01h

	INIT = PORTADR(022h) BYTE 11010000	; GPCS0# mask register 0D0h
	INIT = PORTADR(023h) BYTE 00000111	; A2-A0 = don't care
						; GPCS1 = 3F6h - 3F7h
	INIT = PORTADR(022h) BYTE 11010101	; GPCS1# low address 0D5h
	INIT = PORTADR(023h) BYTE 11110110	; A7-A0 = F6h

	INIT = PORTADR(022h) BYTE 11011001	; GPCS1# high address 0D9h
	INIT = PORTADR(023h) BYTE 00000011	; A15-A80 = 03h

	INIT = PORTADR(022h) BYTE 11010001	; GPCS1# mask register 0D1h
	INIT = PORTADR(023h) BYTE 00000001	; A0 = don't care

	INIT = PORTADR(022h) BYTE 11000001	; Peripheral enable reg.B 0C1h
	INIT = PORTADR(023h) BYTE rrrrrr11	; Enable GPCS0# and GPCS1#

	INIT = PORTADR(022h) BYTE 11000100	; FDC config. register 0C4h
	INIT = PORTADR(023h) BYTE rrrrr1rr	; XD buffer enable

	PORT = 3F6H
	  SIZE = BYTE
	  SHARE = NO
	PORT = 1F0H-1F7H
	  SIZE = WORD
	  SHARE = NO
	PORT = 3F7H
          SHARE = YES
          SIZE = WORD
        IRQ = 14
          SHARE = NO
          TRIGGER = EDGE

ENDGROUP

;------------------------------------------------------------------------------
;                             Shadowing Options
;------------------------------------------------------------------------------

GROUP =  "Shadowing Options:"
 FUNCTION = "Video BIOS Shadow"
   COMMENTS = "Shadowing area C0000h-C7FFFh"
   CHOICE = "Video BIOS Shadow:  Enabled"
	FREE
  	   INIT = PORTADR(0C00h) BYTE 00011111
	   INIT = PORTADR(8C8h) BYTE rrrrrr1r
   CHOICE = "Video BIOS Shadow:  Disabled"
     	FREE
	  INIT = PORTADR(0C00h) BYTE 00011111
          INIT = PORTADR(8C8h) BYTE rrrrrr0r

 FUNCTION = "System BIOS Shadow"
   COMMENTS = "Shadowing area F0000h-FFFFFh"
   CHOICE = "System BIOS Shadow:  Enabled"
     	FREE
	  INIT = PORTADR(0C00h) BYTE 00011111
  	  INIT = PORTADR(8C8h) BYTE rrrrrrr1
   CHOICE = "System BIOS Shadow:  Disabled"
     	FREE
	  INIT = PORTADR(0C00h) BYTE 00011111
     	  INIT = PORTADR(8C8h) BYTE rrrrrrr0
ENDGROUP

;------------------------------------------------------------------------------
;                                Caching Options
;------------------------------------------------------------------------------

GROUP = "Caching Options:"
 FUNCTION = "Global Caching"
   COMMENTS = "This function will enable/disable caching.  If this function 
               is disabled, selection of the 'Enable' choice of the following 
               three functions are ineffective."
   CHOICE = "Global Caching:  Enabled"
    	FREE
	  INIT = PORTADR(0C00h) BYTE 00011111	
    	  INIT = PORTADR(8C8h) BYTE 1rrrrrrr
   CHOICE = "Global Caching:  Disabled"
     	FREE
	  INIT = PORTADR(0C00h) BYTE 00011111
          INIT = PORTADR(8C8h) BYTE 0rrrrrrr

 FUNCTION = "Video BIOS and Expansion ROM Cache"
   COMMENTS = "Cache area C0000h-EFFFFh\nIf you choose to Enable this function
               you must make certain the the 'Global Caching' function above is
               also enabled."
   CHOICE = "Video BIOS and Expansion ROM Cache:  Enabled"
     	FREE
	  INIT = PORTADR(0C00h) BYTE 00011111
     	  INIT = PORTADR(8C8h) BYTE r11rrrrr

   CHOICE = "Video BIOS and Expansion ROM Cache:  Disabled"
     	FREE
	  INIT = PORTADR(0C00h) BYTE 00011111
    	  INIT = PORTADR(8C8h) BYTE r00rrrrr

 FUNCTION = "System BIOS Cache"
  SHOW = NO
  CHOICE = "System BIOS Cache:  Disabled"
     	FREE
	  INIT = PORTADR(0C00h) BYTE 00011111
     	  INIT = PORTADR(8C8h) BYTE rrr0rrrr
	  MEMORY = 64K
	  ADDRESS = 0F0000H
	  CACHE = NO
	  WRITABLE = NO

ENDGROUP

;------------------------------------------------------------------------------
;                  Extented features to support misc. functions
;------------------------------------------------------------------------------

GROUP = "Misc. Setup Functions"

 FUNCTION = "Installed CPU Module Speed"
   SHOW = NO
   CHOICE = "20 Mhz"
    	FREE
	  INIT = PORTADR(0C00h) BYTE 00011111
     	  INIT = PORTADR(8C9h) BYTE r001rrrr		; 20 MHz
	  INIT = PORTADR(0C00H) BYTE 00011111
	  INIT = PORTADR(8CAH) BYTE 01001111		;LOW = 4FH = 8MHz
	  INIT = PORTADR(0C00H) BYTE 00011111
	  INIT = PORTADR(8CBH) BYTE 00110111		;MED = 37H = 12MHz

 FUNCTION = "DRAM Speed"
   COMMENTS = "This function will select the DRAM speed"

   CHOICE = "DRAM Speed:  80 ns"
     FREE
	INIT = PORTADR(0C00h) BYTE 00011111	; Select Last Page of EISA CMOS
     	INIT = PORTADR(8C9h) BYTE rrrr10rr	; 80ns DRAM 

	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000001	; Enable the DRAMC

	INIT = PORTADR(022h) BYTE 00001010	; Mode Register C offset 0Ah
	INIT = PORTADR(023h) BYTE r1rrrrrr	; 1BCLK for EISA Burst Cycle

	INIT = PORTADR(022h) BYTE 00001010	; Mode Register C offset 0Ah
	INIT = PORTADR(023h) BYTE 1rrrrrrr	; 2BCLK for EISA Single Cycle
	

   CHOICE = "DRAM Speed:  70 ns"
     FREE
	INIT = PORTADR(0C00h) BYTE 00011111	; Select Last Page of EISA CMOS
     	INIT = PORTADR(8C9h) BYTE rrrr01rr	; 70ns DRAM

	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000001	; Enable the DRAMC

	INIT = PORTADR(022h) BYTE 00001010	; Mode Register C offset 0Ah
	INIT = PORTADR(023h) BYTE r1rrrrrr	; 1BCLK for EISA Burst Cycle

	INIT = PORTADR(022h) BYTE 00001010	; Mode Register C offset 0Ah
	INIT = PORTADR(023h) BYTE 1rrrrrrr	; 2BCLK for EISA Single Cycle


FUNCTION = "Display Adapter Card"
   COMMENTS = "This setting must reflect the selection in the AT SETUP window."
   CONNECTION = "J6:   1 = Color   0 = Monochrome"

   CHOICE = "Display Adapter Card:  Color"
        FREE
           INIT = JUMPER(6) LOC(1) 1
   CHOICE = "Display Adapter Card:  Monochrome"
        FREE
           INIT = JUMPER(6) LOC(1) 0

 FUNCTION = "Memory Remap"
   COMMENTS = "Enabling Memory Remap will allow unused DRAM to be mapped to 
               the end of extended memory, thereby increasing the amount of 
               extended memory."
   CHOICE = "Memory Remap:  Disabled"
     FREE
	INIT = PORTADR(0C00h) BYTE 00011111
    	INIT = PORTADR(8C8h) BYTE rrrr0rrr
   CHOICE = "Memory Remap:  Enabled"
     FREE
	INIT = PORTADR(0C00h) BYTE 00011111
     	INIT = PORTADR(8C8h) BYTE rrrr1rrr


 FUNCTION = "Restricted Bursts (Host to System accesses > 1 Meg)"
   COMMENTS = "Disabled -- Allows host to system accesses > 1 Meg to be bursted
               Enabled  -- Host to system accesses > 1 Meg are non-burstable"
   CHOICE = "Restricted Bursts:  Disabled"
     FREE
	INIT = PORTADR(022h) BYTE 00100001
	INIT = PORTADR(023h) BYTE 00000001	; Enable the DRAMC

	INIT = PORTADR(022h) BYTE 00001001	; Mode Register B offset 09h
	INIT = PORTADR(023h) BYTE rrrrrrr0	; Disable restricted bursts

   CHOICE = "Restricted Bursts:  Enabled"
     FREE
	INIT = PORTADR(022h) BYTE 00100001    
	INIT = PORTADR(023h) BYTE 00000001	; Enable the DRAMC

	INIT = PORTADR(022h) BYTE 00001001	; Mode Register B offset 09h
	INIT = PORTADR(023h) BYTE rrrrrrr1	; Enable restricted bursts


FUNCTION = "Bus Master Time-out NMI"
   CHOICE = "Bus Master Time-out NMI:  Disabled"
     FREE
	INIT = PORTADR(0C00h) BYTE 00011111
    	INIT = PORTADR(8D0h) BYTE rrrr0rrr
   CHOICE = "Bus Master Time-out NMI:  Enabled"
     FREE
	INIT = PORTADR(0C00h) BYTE 00011111
     	INIT = PORTADR(8D0h) BYTE rrrr1rrr

FUNCTION = "Fail Safe Timer NMI"
   CHOICE = "Fail Safe Timer NMI:  Disabled"
     FREE
	INIT = PORTADR(0C00h) BYTE 00011111
    	INIT = PORTADR(8D0h) BYTE rrrrr0rr
   CHOICE = "Fail Safe Timer NMI:  Enabled"
     FREE
	INIT = PORTADR(0C00h) BYTE 00011111
     	INIT = PORTADR(8D0h) BYTE rrrrr1rr

FUNCTION = "Software I/O Port NMI"
   CHOICE = "Software I/O Port NMI:  Disabled"
     FREE
	INIT = PORTADR(0C00h) BYTE 00011111
    	INIT = PORTADR(8D0h) BYTE rrrrrr0r
   CHOICE = "Software I/O Port NMI:  Enabled"
     FREE
	INIT = PORTADR(0C00h) BYTE 00011111
     	INIT = PORTADR(8D0h) BYTE rrrrrr1r


 ENDGROUP