BOARD           ; 11/03 dar New, 12/01 fcm Chg
 ID="ISAD402"
 NAME="Western Digital WD1006V-SR2 Winchester/Floppy Controller"
 MFR="Western Digital"
 CATEGORY="MSD"
 SLOT=ISA16
 COMMENTS="The floppy controller on this board cannot be
disabled.  W2 is the only jumper configurable without
solder.  The DMA and IRQ functions are not changeable.  The
defaults are:  DMA=2, IRQ=6 for the floppy controller and
IRQ=14 for the hard disk controller."

   HELP=" Use the V)iew D)etail by Slot mode to see Configuration options.  Use E)dit Change F)unction to select Options."

JUMPER (1) = 3
 NAME="W1"
 JTYPE=PAIRED
 VERTICAL=NO
 REVERSE=YES
 LABEL=LOC(1-3) "1" "3" "5"
 COMMENTS="These jumpers are solder pads on the board.
Valid solder connection options are '1-2, 3-4, 5-6.  The
default values are 'not installed'."

 JUMPER (2) = 1
 NAME="W2"
 JTYPE=PAIRED
 VERTICAL=YES
 REVERSE=YES
 LABEL=LOC(1)"1 - 2"

JUMPER (3) = 1
 NAME="W3"
 JTYPE=PAIRED
 VERTICAL=YES
 REVERSE=YES
 LABEL=LOC(1) "1 - 2"
 COMMENTS="This jumper is solder pads on the board.  The
default value is 'not installed'."

JUMPER (4) = 1
 NAME="W4"
 JTYPE=PAIRED
 VERTICAL=YES
 REVERSE=YES
 LABEL=LOC(1)"1 - 2"
 COMMENTS="This jumper is solder pads on the board.  The
default value is 'not installed'."

JUMPER (5) = 1
 NAME="W5"
 JTYPE=PAIRED
 VERTICAL=NO
 REVERSE=NO
 LABEL=LOC(1) "1|2"
 COMMENTS="This jumper is solder pads on the board.  The
default value is 'not installed'."

SOFTWARE(1)="Hard disk drives attached to the Western
Digital WD1006V-SR2 Winchester/Floppy controller board
require low level formatting.  Formatting may be
accomplished by special software available from several
vendors, or by the on-board BIOS ROM.  To format with the
BIOS ROM, load the DEBUG utility.  At the DEBUG prompt,
enter'g=cc05:5' and follow the menu prompts.  Refer to
the drive manufacturer's documentation for details on the
configuration procedure."

FUNCTION="Fixed Disk Controller"
TYPE="MSD,DSKCTL"
HELP="Use E)dit Change R)esource to Select Options."

CHOICE="Primary"
SUBTYPE="CTL0"
 LINK
  PORT=1F0h-1F7h
  PORT=3F6h
  PORT=3F7h
  SHARE=YES
  IRQ=14
  INIT=JUMPER(2)LOC(1)       0
CHOICE="Secondary"
SUBTYPE="CTL1"
 LINK
  PORT=170h-177h
  PORT=376h
  PORT=377h
  SHARE=YES
  IRQ=14
  INIT=JUMPER(2)LOC(1)      1

FUNCTION="Diskette Controller"
CHOICE="Primary"
 LINK
  PORT=3F0h-3F5h
  PORT=3F7h
  SHARE=YES
  DMA=2
  IRQ=6
  INIT=JUMPER(3)LOC(1)      0
CHOICE="Secondary"
 LINK
  PORT=370h-375h
  PORT=377h
  SHARE=YES
  DMA=2
  IRQ=6
  INIT=JUMPER(3)LOC(1)      1

FUNCTION="Operational Options"
HELP="Use E)dit Change F)unction to Select Options."

SUBFUNCTION="Winchester Mode"
CHOICE="Latched"
 FREE
  INIT=JUMPER(1) LOC (1)   0
CHOICE="Non-Latched"
 FREE
  INIT=JUMPER(1) LOC (1)    1

SUBFUNCTION="ECC Length"
 CHOICE="4Byte"
   FREE
   INIT=JUMPER(1) LOC (2)    0
 CHOICE="Reserved"
   FREE
   INIT=JUMPER(1) LOC (2)    1

SUBFUNCTION="Cacheing"
 CHOICE="Enabled"
   FREE
   INIT=JUMPER(1) LOC (3)    0
 CHOICE="Disabled"
   FREE
   INIT=JUMPER(1) LOC (3)    1

SUBFUNCTION="Floppy Drive Type"
COMMENTS="Do not mix single speed and dual speed floppies
in the same system"
 CHOICE="Single Speed Floppy"
   FREE
   INIT=JUMPER(4)LOC(1)      0
 CHOICE="Dual Speed Floppy"
   FREE
   INIT=JUMPER(4)LOC(1)      1

SUBFUNCTION="Bracket Ground Connection"
 CHOICE="Bracket Ground Option Not Used"
   FREE
   INIT=JUMPER(5)LOC(1)      0
 CHOICE="Bracket Grounded to Board"
   FREE
   INIT=JUMPER(5)LOC(1)      1