; ; Acer E5 Card ; BOARD ID = "ISAE005" NAME = "ACER E5 CARD" MFR = "Acer America" CATEGORY = "MFC" SLOT = ISA16 LENGTH = 250 ; Approximate length AMPERAGE = 1000 ; 1A SKIRT = NO READID = NO DISABLE = UNSUPPORTED COMMENTS="This board supplies a floppy disk drive controller, an IDE interface, two asynchronous serial ports, a parallel port, and a VGA port." JUMPER(2) = 2 NAME = "J2" JTYPE = INLINE VERTICAL = YES REVERSE = YES LABEL = LOC(1 2 3) "1" "2" "3" FACTORY = LOC(1^2) 1 COMMENTS = "The post 1^2 supports two diskette drives \n The post 2^3 is reserved." JUMPER(3) = 2 NAME = "J3" JTYPE = INLINE VERTICAL = YES REVERSE = YES LABEL = LOC(1 2 3) "1" "2" "3" FACTORY = LOC(1^2 2^3) 10 COMMENTS = "This jumper determines diskette select enable (1^2) or diskette select disable (2^3)." JUMPER(5) = 2 NAME = "J5" JTYPE = INLINE VERTICAL = YES REVERSE = YES LABEL = LOC(1 2 3) "1" "2" "3" FACTORY = LOC(1^2 2^3) 10 COMMENTS = "This jumper determines the COM1 and COM2 ports.\n\n J5 J6 J7 COM1 COM2\n 1^2 1^2 1^2 Enabled Enabled\n 1^2 2^3 1^2 Enabled Disabled\n 1^2 1^2 2^3 Disabled Enabled\n 1^2 2^3 2^3 Disabled Disabled" JUMPER(6) = 2 NAME = "J6" JTYPE = INLINE VERTICAL = YES REVERSE = YES LABEL = LOC(1 2 3) "1" "2" "3" FACTORY = LOC(1^2 2^3) 10 COMMENTS = "This jumper determines the COM1 and COM2 ports.\n\n J5 J6 J7 COM1 COM2\n 1^2 1^2 1^2 Enabled Enabled\n 1^2 2^3 1^2 Enabled Disabled\n 1^2 1^2 2^3 Disabled Enabled\n 1^2 2^3 2^3 Disabled Disabled" JUMPER(7) = 2 NAME = "J7" JTYPE = INLINE VERTICAL = YES REVERSE = YES LABEL = LOC(1 2 3) "1" "2" "3" FACTORY = LOC(1^2 2^3) 10 COMMENTS = "This jumper determines the COM1 and COM2 ports.\n\n J5 J6 J7 COM1 COM2\n 1^2 1^2 1^2 Enabled Enabled\n 1^2 2^3 1^2 Enabled Disabled\n 1^2 1^2 2^3 Disabled Enabled\n 1^2 2^3 2^3 Disabled Disabled" JUMPER(9) = 2 NAME = "J9" JTYPE = INLINE VERTICAL = YES REVERSE = YES LABEL = LOC(1 2 3) "1" "2" "3" FACTORY = LOC(1^2 2^3) 10 COMMENTS = "This jumper determines the Parallel ports.\n\n J9 J10 Parallel Port\n 1^2 1^2 LPT2\n 1^2 2^3 LPT1\n 2^3 1^2 LPT3\n 2^3 2^3 Disable" JUMPER(10) = 2 NAME = "J10" JTYPE = INLINE VERTICAL = YES REVERSE = YES LABEL = LOC(1 2 3) "1" "2" "3" FACTORY = LOC(1^2 2^3) 01 COMMENTS = "This jumper determines for the Parallel ports.\n\n J9 J10 Parallel Port\n 1^2 1^2 LPT2\n 1^2 2^3 LPT1\n 2^3 1^2 LPT3\n 2^3 2^3 Disable" JUMPER(11) = 2 NAME = "J11" JTYPE = INLINE VERTICAL = YES REVERSE = YES LABEL = LOC(1 2 3) "1" "2" "3" FACTORY = LOC (1^2 2^3) 01 COMMENTS = "This jumper enable VGA 2^3." JUMPER(12) = 2 NAME = "J12" JTYPE = INLINE VERTICAL = NO REVERSE = YES LABEL = LOC(1 2 3) "1" "2" "3" FACTORY = LOC (1^2 2^3) 01 COMMENTS = "This jumper enable VGA 2^3." JUMPER(13) = 2 NAME = "J13" JTYPE = INLINE VERTICAL = NO REVERSE = YES LABEL = LOC(1 2 3) "1" "2" "3" FACTORY = LOC (1^2 2^3) 01 COMMENTS = "A jumper across 2 and 3 set the data width to 16 bit or post 1 and 2 will set the data width to 8 bit." JUMPER(14) = 2 NAME = "J14" JTYPE = INLINE VERTICAL = NO REVERSE = YES LABEL = LOC(1 2 3) "1" "2" "3" FACTORY = LOC (1^2 2^3) 10 COMMENTS = "A jumper across 1 and 2 enable HW/SW, and jumper across 2 and 3 is reserved." JUMPER(17) = 1 NAME = "J17" JTYPE = INLINE VERTICAL = YES REVERSE = YES LABEL = LOC(1 2) "1" "2" COMMENTS = "This jumper determines enable/disable IDE." JUMPER(18) = 1 NAME = "J18" JTYPE = INLINE VERTICAL = YES REVERSE = YES LABEL = LOC(1 2) "1" "2" COMMENTS = "This jumper determines enable/disable IDE." FUNCTION = "Floppy Disk Controller" TYPE = "MSD,FPYCTL" COMMENTS = "This controller is a superset of the typical ISA floppy disk controller. It can support a maximum of two floppy drives Any combination of 5 1/4 or 3 1/2 (non-PS/2) floppy drives may be used." HELP = "This section of the board can be disabled in order to allow the use of other cards that require this address range." CHOICE = "FFD Enable" FREE IRQ = 6 SHARE = NO TRIGGER = EDGE PORT = 03F7h SIZE = BYTE SHARE = "ATtskfl" DMA = 2 SIZE = BYTE TIMING = TYPEB INIT = JUMPER(2)LOC(1^2) 1 ;Always enabled 2 FFD INIT = JUMPER(3)LOC(1^2 2^3) 10 ;Always enabled CHOICE = "FFD Disable " FREE INIT = JUMPER(3)LOC(1^2 2^3) 00 ;Always disabled FUNCTION = "IDE Interface" TYPE = "MSD,IDE" COMMENTS = "The IDE interface is software compatible with a standard AT hard disk controller." HELP = "This section of the board can be disabled in order to allow the use of other cards that require this address range." CHOICE = "IDE Enable" LINK IRQ = 14 SHARE = NO TRIGGER = EDGE FREE PORT = 001f0h - 001f7h SIZE = BYTE PORT = 003f6h INIT = JUMPER(17)LOC(1^2) 1 ;Always enabled INIT = JUMPER(18)LOC(1^2) 1 ;Always enabled CHOICE = "IDE Disable" FREE INIT = JUMPER(17)LOC(1^2) 0 ;Always disabled INIT = JUMPER(18)LOC(1^2) 0 ;Always disabled FUNCTION = "Parallel Port " TYPE = "PAR" COMMENTS = "The parallel port has a standard 25 pin connector and is a superset of a typical ISA parallel port." HELP = "This section of the board can be disabled in order to allow the use of other cards that require this address range." CHOICE = "LPT1" FREE IRQ = 7 SHARE = NO TRIGGER = EDGE PORT = 03BCh-03BEh SIZE = BYTE SHARE = "lpt" ;This port affects all printers SIZE = BYTE INIT = JUMPER(9)LOC(1^2 2^3) 10 ;A parallel port at lpt1 INIT = JUMPER(10)LOC(1^2 2^3) 01 ;A parallel port at lpt1 CHOICE = "LPT2" FREE IRQ = 7 SHARE = NO TRIGGER = EDGE PORT = 0378h-037Ah SIZE = BYTE SHARE = "lpt" ;This port affects all printers SIZE = BYTE INIT = JUMPER(9)LOC(1^2 2^3) 10 ;A parallel port at lpt2 INIT = JUMPER(10)LOC(1^2 2^3) 10 ;A parallel port at lpt2 CHOICE = "LPT3" FREE IRQ = 7 SHARE = NO TRIGGER = EDGE PORT = 0278h-027Ah SIZE = BYTE SHARE = "lpt" ;This port affects all printers SIZE = BYTE INIT = JUMPER(9)LOC(1^2 2^3) 01 ;A parallel port at lpt3 INIT = JUMPER(10)LOC(1^2 2^3) 10 ;A parallel port at lpt3 CHOICE = "Parallel port disable" DISABLE = yes FREE INIT = JUMPER(9)LOC(1^2 2^3) 01 ;parallel port disabled INIT = JUMPER(10)LOC(1^2 2^3) 01 ;parallel port disabled FUNCTION = " 9 pin Serial port " TYPE = "COM,ASY" COMMENTS = "The serial port has a standard 9 and 25 pin connector and is a superset of a typical ISA serial port." HELP = "This section of the board can be disabled in order to allow the use of other cards that require this address range." CHOICE = "9-COM1" FREE IRQ = 4 SHARE = NO TRIGGER = EDGE PORT = 03F8h-03FFh SIZE = BYTE INIT = JUMPER(5)LOC(1^2 2^3) 10 INIT = JUMPER(7)LOC(1^2 2^3) 10 CHOICE = "9 & 25 pin serial port disable" DISABLE = yes FREE INIT = JUMPER(5)LOC(1^2 2^3) 10 INIT = JUMPER(7)LOC(1^2 2^3) 01 FUNCTION = "25 pin Serial Port " TYPE = "COM,ASY" COMMENTS = "The serial port has a standard 25 pin connector and is a superset of a typical ISA serial port." HELP = "This section of the board can be disabled in order to allow the use of other cards that require this address range." CHOICE = "25-COM2" FREE IRQ = 3 SHARE = NO TRIGGER = EDGE PORT = 02F8h-02FFh SIZE = BYTE INIT = JUMPER(5)LOC(1^2 2^3) 10 INIT = JUMPER(6)LOC(1^2 2^3) 10 CHOICE = "9 & 25 pin serial port disable" DISABLE = yes FREE INIT = JUMPER(5)LOC(1^2 2^3) 10 INIT = JUMPER(6)LOC(1^2 2^3) 01 FUNCTION="Video Selection" TYPE = "VGA" SUBFUNCTION = "Display" CHOICE = "Enable Graphic or Text" LINK PORT = 03C0h - 03Cfh PORT = 03D0h - 03Dfh LINK MEMORY=32k ADDRESS=0B0000h MEMTYPE=OTH LINK MEMORY=32k ADDRESS=0B8000h MEMTYPE=OTH FREE INIT = JUMPER(11) LOC(1^2 2^3) 01 INIT = JUMPER(12) LOC(1^2 2^3) 01 CHOICE = "Disable" DISABLE = YES FREE INIT = JUMPER(11) LOC(1^2 2^3) 10 ;Always disable INIT = JUMPER(12) LOC(1^2 2^3) 10 ;Always disable SUBFUNCTION = "Data Width" CHOICE = "16 bits" LINK MEMORY=32k ADDRESS=0C0000h MEMTYPE = OTH WRITABLE = NO FREE INIT = JUMPER(13) LOC(1^2 2^3) 01 CHOICE = "8 bits" LINK MEMORY=32k ADDRESS=0C0000h MEMTYPE = OTH WRITABLE = NO FREE INIT = JUMPER(13) LOC(1^2 2^3) 10