;!ITC1001.CFG  For 486
;
;
; INTEL 486 EISA Evaluation Board
;
BOARD
	ID="ITC1001"
	NAME="Intel 486 EISA Evaluation Board"
	MFR="INTEL FOLSOM"
	CATEGORY="SYS"
	SLOT=EMB(0)
	READID=YES
	COMMENTS="This is the Board Identification Block comment field for the Intel 486 EISA Evaluation Board"
	HELP="This is the main board configuration help field for the Intel 486 EISA Evaluation Board."

SYSTEM
	NONVOLATILE=8192
	SLOT(1)=EISA
		LENGTH=341
		BUSMASTER=YES
	SLOT(2)=EISA
		LENGTH=341
		BUSMASTER=YES
	SLOT(3)=EISA
		LENGTH=341
		BUSMASTER=YES
	SLOT(4)=EISA
		LENGTH=341
		BUSMASTER=YES
	SLOT(5)=EISA
		LENGTH=341
		BUSMASTER=YES
	SLOT(6)=EISA
		LENGTH=341
		BUSMASTER=YES
	SLOT(7)=ISA8
		LENGTH=341
		BUSMASTER=NO
	SLOT(8)=ISA8
		LENGTH=341
		BUSMASTER=NO

	MEMORY=640K 	ADDRESS = 0 	CACHE = YES STEP = 32K
	MEMORY = 15M
	ADDRESS = 1M	CACHE = YES STEP = 32K

SWITCH(1) = 7
	NAME = "Video Type Select"
	STYPE = DIP
	VERTICAL = NO
	REVERSE = YES
;	LABEL = LOC(1 2 3 4 5 6 7) "1" "2" "3" "4" "5" "6" "7"
	INITVAL = LOC(1 2 3 4 5 6 7) 110111x
	FACTORY = LOC(1 2 3 4 5 6 7) 1101110		;Color default
	COMMENTS = "Position 7 controls video type:	
			On=0:  Color Video Controller		
			Off=1: Monochrome Video Controller	
			(other switch positions are TBD)."

JUMPER(23) = 1
	NAME = "I/O Recovery"
	JTYPE = PAIRED
	VERTICAL = YES
	LABEL = LOC(1) "J23"
	INITVAL = LOC(1) 1	;Show as connected
	FACTORY = LOC(1) 1	;Active is default
	COMMENTS = "This jumper enables/Disables I/O Recovery.  Installed
			is active."

JUMPER(15) = 1
	NAME = "Floppy Type Select"
	JTYPE = TRIPOLE
	REVERSE = YES
	VERTICAL = YES
	LABEL = LOC(1) "J15"
	FACTORY = LOC(1) 1		;5 1/4 Enabled
	COMMENTS = "Right-hand position: 5 1/4 inch operation,	
			Left-hand position: 3 1/2 inch operation."

JUMPER(12)=1
	NAME="FDC chip select"
	JTYPE = PAIRED
	VERTICAL = YES
	LABEL = LOC(1) "J12"
	FACTORY = LOC(1) 1
	COMMENTS="This jumper enables(installed)/disables on-board floppy."

JUMPER(14)=1
	NAME="FDC DMA ACK"
	JTYPE=PAIRED
	VERTICAL = YES
	LABEL=LOC(1) "J14"
	FACTORY=LOC(1) 1
	COMMENTS="This jumper controls on-board floppy DMA ACK Assertion.
			Installed for on-boad floppy."

JUMPER(16)=1
	NAME="FDC IRQ"
	JTYPE=PAIRED
	VERTICAL = YES
	LABEL=LOC(1) "J17"
	FACTORY=LOC(1) 1
	COMMENTS="This jumper controls on-board floppy IRQ Assertion.
			Installed for on-board floppy."

JUMPER(17)=1
	NAME="FDC DMA REQ"
	JTYPE=PAIRED
	VERTICAL = YES
	LABEL=LOC(1) "J16"
	FACTORY=LOC(1) 1
	COMMENTS="This jumper controls on-board floppy DMA REQ Assertion.
			Installed for on-boad floppy."

JUMPER(27) = 1
	NAME = "C6 Cache Operation"
	JTYPE = TRIPOLE
	REVERSE = YES
	VERTICAL = YES
	INITVAL = LOC(1) 1
	LABEL = LOC(1) "J27"
	FACTORY = LOC(1) 1		;Disabled ??? Is pin one on left?
	COMMENTS = "Jumper installed in right-hand position disables cache."

JUMPER(26)=4				;4 positions
	NAME="Memory Config J26"
	JTYPE=PAIRED
	VERTICAL=YES
	REVERSE=YES			;Pin 1 on top
	LABEL=LOC(1-4) "RAS A" "RAS B" "RAS C" "RAS D"
	FACTORY=LOC(1-4) 1111		;No 2-MB SIMMs used
;	INITVAL=LOC(1-4) 1111
	COMMENTS="Install 2-MB SIMMs before 1-MB SIMMs, starting at U1.
		Remove jumper for each RASx with 2-MB SIMMs."


;SYSTEM BOARD RESOURCES

GROUP="Basic Main Board Functions"
	TYPE="SYS"

FUNCTION="TIMER"
	COMMENTS="Reserves IRQ, DMA and other resources"
	HELP="Help field for system board resources"
	CHOICE="Reserved"
		FREE
			IRQ=0

FUNCTION="Real-time Clock"
	CHOICE="Reserved"
		FREE
			IRQ=8
			PORT=70H-71H

FUNCTION="Co-processor"
	TYPE="NPX,387"
	CHOICE="Installed"
		LINK
			IRQ=13
	CHOICE="Not Installed"
		DISABLE=YES

ENDGROUP


FUNCTION="Keyboard"
	TYPE="KEY"
	CHOICE="101 Key"
		SUBTYPE="101"
		LINK
			IRQ=1
			PORT=60H
			PORT=64H
	CHOICE="83 Key"
		SUBTYPE="083"
		LINK
			IRQ=1

FUNCTION="System board AT compatible floppy controller"
	TYPE="MSD,FPYCTL"
	CONNECTION="Connector J15 with pin 1 on left"
	HELP="This is the AT compatible floppy disk controller that is
		integrated on the system board.This should not be enabled 
		if there is another floppy controller in the system."
	CHOICE="Enabled 5 1/4"
		LINK
			DMA=2
				SHARE=NO
				SIZE=BYTE
				TIMING=TYPEA
			IRQ=6
				SHARE=NO
				TRIGGER=EDGE
			PORT=3F4H-3F5H
				SHARE=NO
				SIZE=BYTE
			INIT=JUMPER(12) LOC(1) 1
			INIT=JUMPER(14) LOC(1) 1
			INIT=JUMPER(15) LOC(1) 1	;for 5 1/4
			INIT=JUMPER(16) LOC(1) 1
			INIT=JUMPER(17) LOC(1) 1

	CHOICE="Enabled 3 1/2"
		LINK
			DMA=2
				SHARE=NO
				SIZE=BYTE
				TIMING=TYPEA
			IRQ=6
				SHARE=NO
				TRIGGER=EDGE
			PORT=3F4H-3F5H
				SHARE=NO
				SIZE=BYTE
			INIT=JUMPER(12) LOC(1) 1
			INIT=JUMPER(14) LOC(1) 1
			INIT=JUMPER(15) LOC(1) 0	;for 3 1/2
			INIT=JUMPER(16) LOC(1) 1
			INIT=JUMPER(17) LOC(1) 1

	CHOICE="Disabled"
		DISABLE = YES
		LINK
			INIT=JUMPER(12) LOC(1) 0
			INIT=JUMPER(14) LOC(1) 0
			INIT=JUMPER(16) LOC(1) 0
			INIT=JUMPER(17) LOC(1) 0

GROUP="System Board Memory Functions"

FUNCTION="System Board Base Memory"
	TYPE="MEM"
	COMMENTS="Selects 640k base memory for the 486 System Board."
	HELP="This memory always exists."
	CHOICE="640K base memory (default)"
		HELP ="Only choice is 640k base memory for the 486 System Board"
	LINK
	MEMORY=640K
		ADDRESS=0H
		WRITABLE=YES
		MEMTYPE=SYS
		CACHE=YES
								  
FUNCTION="System Board Memory at 1MB"
	TYPE="MEM"
	COMMENTS="Selects SIMM types (SD or DD) for the 486 System Board."
	HELP="Double Density (DD) 2-MB SIMMs are placed at the lower memory addresses
		first, the single density (SD) 1-MB SIMMs follow.  The first
		MB of the SIMMs is already used for Base Memory."

	CHOICE="No DD SIMMs 4 SD SIMMs (4 MB total, includes base, default) "
		HELP ="All jumper blocks installed on J26."
		LINK
		MEMORY=3M 
			ADDRESS=1M
			WRITABLE=YES
			MEMTYPE=SYS
			CACHE=YES
		INIT = JUMPER(26) LOC(1-4) 1111 

	CHOICE="No DD SIMMs 2 SD SIMMs (2 MB total, includes base) "
		HELP ="All jumper blocks installed on J26."
		LINK
		MEMORY=1M 
			ADDRESS=1M
			WRITABLE=YES
			MEMTYPE=SYS
			CACHE=YES
		INIT = JUMPER(26) LOC(1-4) 1111 

	CHOICE="No DD SIMMs 6 SD SIMMs (6 MB total, includes base) "
		HELP ="All jumper blocks installed on J26."
		LINK
		MEMORY=5M 
			ADDRESS=1M
			WRITABLE=YES
			MEMTYPE=SYS
			CACHE=YES
		INIT = JUMPER(26) LOC(1-4) 1111 

	CHOICE="No DD SIMMs 8 SD SIMMs (8 MB total, includes base) "
		HELP ="All jumper blocks installed on J26."
		LINK
		MEMORY=7M 
			ADDRESS=1M
			WRITABLE=YES
			MEMTYPE=SYS
			CACHE=YES
		INIT = JUMPER(26) LOC(1-4) 1111 


;;;;;;;;;;;;;;

	CHOICE="2 DD SIMMs No SD SIMMs (4 MB total, includes base) "
		HELP ="Remove jumper block 1 (top) on J26"
		LINK
		MEMORY= 3M 
			ADDRESS=1M
			WRITABLE=YES
			MEMTYPE=SYS
			CACHE=YES
		INIT = JUMPER(26) LOC(1-4) 0111

	CHOICE="2 DD SIMMs 2 SD SIMM (6 MB total, includes base) "
		HELP ="Remove jumper block 1 (top) on J26"
		LINK
		MEMORY= 5M 
			ADDRESS=1M
			WRITABLE=YES
			MEMTYPE=SYS
			CACHE=YES
		INIT = JUMPER(26) LOC(1-4) 0111

	CHOICE="2 DD SIMMs 4 SD SIMMs (8 MB total, includes base) "
		HELP ="Remove jumper block 1 (top) on J26"
		LINK
		MEMORY= 7M 
			ADDRESS=1M
			WRITABLE=YES
			MEMTYPE=SYS
			CACHE=YES
		INIT = JUMPER(26) LOC(1-4) 0111

	CHOICE="2 DD SIMMs 6 SD SIMMs (10 MB total, includes base) "
		HELP ="Remove jumper block 1 (top) on J26"
		LINK
		MEMORY= 9M 
			ADDRESS=1M
			WRITABLE=YES
			MEMTYPE=SYS
			CACHE=YES
		INIT = JUMPER(26) LOC(1-4) 0111

;;;;;;;;;;;;;;;;

	CHOICE="4 DD SIMMs No SD SIMMs (8 MB total, includes base)"
		HELP ="Remove jumper blocks 1 and 2 (top 2) on J26"
		LINK
		MEMORY= 7M 
			ADDRESS=1M
			WRITABLE=YES
			MEMTYPE=SYS
			CACHE=YES
		INIT = JUMPER(26) LOC(1-4) 0011 

	CHOICE="4 DD SIMMs 2 SD SIMMs (10 MB total, includes base)"
		HELP ="Remove jumper blocks 1 and 2 (top 2) on J26"
		LINK
		MEMORY= 9M 
			ADDRESS=1M
			WRITABLE=YES
			MEMTYPE=SYS
			CACHE=YES
		INIT = JUMPER(26) LOC(1-4) 0011 

	CHOICE="4 DD SIMMs 4 SD SIMMs (12 MB total, includes base)"
		HELP ="Remove jumper blocks 1 and 2 (top 2) on J26"
		LINK
		MEMORY= 11M 
			ADDRESS=1M
			WRITABLE=YES
			MEMTYPE=SYS
			CACHE=YES
		INIT = JUMPER(26) LOC(1-4) 0011 

;;;;;;;;;

	CHOICE="3 DD SIMMs No SD SIMMs (12 MB total, includes base)"
		HELP ="Remove top 3 jumper blocks on J26"
		LINK
		MEMORY= 11M 
			ADDRESS=1M
			WRITABLE=YES
			MEMTYPE=SYS
			CACHE=YES
		INIT = JUMPER(26) LOC(1-4) 0001

	CHOICE="3 DD SIMMs 2 SD SIMMs (14 MB total, includes base)"
		HELP ="Remove top 3 jumper blocks on J26"
		LINK
		MEMORY= 13M 
			ADDRESS=1M
			WRITABLE=YES
			MEMTYPE=SYS
			CACHE=YES
		INIT = JUMPER(26) LOC(1-4) 0001

;;;;;;;;;;;;;;

	CHOICE="4 DD SIMMs No SD SIMMs (16 MB total, includes base)"
		HELP ="Remove all jumper blocks on J26"
		LINK
		MEMORY= 15M 
			ADDRESS=1M
			WRITABLE=YES
			MEMTYPE=SYS
			CACHE=YES
		INIT = JUMPER(26) LOC(1-4) 0000

		
ENDGROUP