;---------------------------------------------------------------------------- ; ; ; Madge Smart 100 AT Ringnode Configuration File !MDG1020.CFG, Rev. 01.02.00 ; Copyright (c) Madge Networks Ltd. 1993-1995 ; ;---------------------------------------------------------------------------- ; ; This is for the Smart 100 AT Fiber ( Assy No. 114-010-01 ) and ; Smart 100 AT Copper ( Assy No. 114-020-01 ). ; ; Rev. 01.00.00 AD 06/12/93 ; Rev. 01.01.00 MJF 26/01/94 ; Rev. 01.02.00 MJF 14/02/95 ; ; ;---------------------------------------------------------------------------- BOARD ID = "MDG1020" NAME = "Madge Smart 100 AT Ringnode" MFR = "Madge Networks Ltd." CATEGORY = "NET" SLOT = ISA16 LENGTH = 256 AMPERAGE = 1700 SKIRT = NO READID = NO IOCHECK = INVALID DISABLE = UNSUPPORTED COMMENTS = "\n This is a high performance network adapter for AT computers.\n \n The configuration utility will select a conflict-free configuration of system resources. You must set the switches on the card to the values shown.\n \n Six interrupts are supported. Four sets of I/O and memory addresses are possible, allowing upto four adapters to be used in one computer.\n\n" HELP = "Consult the manual that came with this product for details on troubleshooting and how to contact Madge in case of unresolvable problems.\n" ;---------------------------------------------------------------------------- IOPORT(1) = PORTVAR(1) ; con_reg1 INITVAL = 00000000b ;---------------------------------------------------------------------------- SWITCH (1) = 8 NAME = "Adapter switches" STYPE = DIP REVERSE = NO VERTICAL = NO LABEL = LOC (1-8) "IO0" "IO1" "Remoteboot" "MMIO" "Bus Timing" "IRQ0" "IRQ1" "IRQ2" FACTORY = LOC (1-8) 11011010 COMMENTS = "\n The switch settings shown are the REQUIRED settings in order to get the I/O and memory locations, interrupt channel, remoteboot, MMIO and bus timing settings as configured elsewhere in this EISA configuration utility. The switch settings are NOT the current ACTUAL settings.\n" ;---------------------------------------------------------------------------- FUNCTION = "FDDI Fiber/Copper Network Adapter" TYPE = "NET,DDI" ;---------------------------------------------------------------------------- SUBFUNCTION = "Interrupt channel" TYPE = "INT" HELP = "Select an interrupt channel which the adapter can use. This adapter cannot share interrupts with other devices.\n" CHOICE = "IRQ 15 (non-shareable)" SUBTYPE = "INT15" LINK IRQ = 15 SHARE = NO TRIGGER = EDGE INIT = SWITCH(1) LOC(6-8) 001 CHOICE = "IRQ 11 (non-shareable)" SUBTYPE = "INT11" LINK IRQ = 11 SHARE = NO TRIGGER = EDGE INIT = SWITCH(1) LOC(6-8) 010 CHOICE = "IRQ 10 (non-shareable)" SUBTYPE = "INT10" LINK IRQ = 10 SHARE = NO TRIGGER = EDGE INIT = SWITCH(1) LOC(6-8) 011 CHOICE = "IRQ 9 (non-shareable)" SUBTYPE = "INT9" LINK IRQ = 9 SHARE = NO TRIGGER = EDGE INIT = SWITCH(1) LOC(6-8) 100 CHOICE = "IRQ 7 (non-shareable)" SUBTYPE = "INT7" LINK IRQ = 7 SHARE = NO TRIGGER = EDGE INIT = SWITCH(1) LOC(6-8) 101 CHOICE = "IRQ 3 (non-shareable)" SUBTYPE = "INT3" LINK IRQ = 3 SHARE = NO TRIGGER = EDGE INIT = SWITCH(1) LOC(6-8) 110 ;---------------------------------------------------------------------------- SUBFUNCTION = "I/O & Smartrom/MMIO address range" TYPE = "NET,DDI,LOC" HELP = "Please select I/O and memory addresses which the adapter can use. If either remoteboot or MMIO is enabled then make sure that an I/O address range with memory enabled is selected for this adapter card.\n" CHOICE = "I/O 0A20-3F, Memory C8000h-C9FFFh" PORTVAR(1) = 0A26h FREE INIT = SWITCH(1) LOC(2-1) 11 PORT = 0A20h-0A3Fh SIZE = BYTE MEMORY = 8K ADDRESS = 0C8000h WRITABLE = YES MEMTYPE = OTH CACHE = NO SIZE = BYTE DECODE = 20 SHARE = NO CHOICE = "I/O 1A20-3F, Memory DC000h-DDFFFh" PORTVAR(1) = 1A26h FREE INIT = SWITCH(1) LOC(2-1) 10 PORT = 1A20h-1A3Fh SIZE = BYTE MEMORY = 8K ADDRESS = 0DC000h WRITABLE = YES MEMTYPE = OTH CACHE = NO SIZE = BYTE DECODE = 20 SHARE = NO CHOICE = "I/O 2A20-3F, Memory CE000h-CFFFFh" PORTVAR(1) = 2A26h FREE INIT = SWITCH(1) LOC(2-1) 01 PORT = 2A20h-2A3Fh SIZE = BYTE MEMORY = 8K ADDRESS = 0CE000h WRITABLE = YES MEMTYPE = OTH CACHE = NO SIZE = BYTE DECODE = 20 SHARE = NO CHOICE = "I/O 3A20-3F, Memory DE000h-DFFFFh" PORTVAR(1) = 3A26h FREE INIT = SWITCH(1) LOC(2-1) 00 PORT = 3A20h-3A3Fh SIZE = BYTE MEMORY = 8K ADDRESS = 0DE000h WRITABLE = YES MEMTYPE = OTH CACHE = NO SIZE = BYTE DECODE = 20 SHARE = NO CHOICE = "I/O 0A20-3F, Memory disabled" PORTVAR(1) = 0A26h FREE INIT = SWITCH(1) LOC(2-1) 11 INIT = SWITCH(1) LOC(4) 0 PORT = 0A20h-0A3Fh SIZE = BYTE CHOICE = "I/O 1A20-3F, Memory disabled" PORTVAR(1) = 1A26h FREE INIT = SWITCH(1) LOC(2-1) 10 INIT = SWITCH(1) LOC(4) 0 PORT = 1A20h-1A3Fh SIZE = BYTE CHOICE = "I/O 2A20-3F, Memory disabled" PORTVAR(1) = 2A26h FREE INIT = SWITCH(1) LOC(2-1) 01 INIT = SWITCH(1) LOC(4) 0 PORT = 2A20h-2A3Fh SIZE = BYTE CHOICE = "I/O 3A20-3F, Memory disabled" PORTVAR(1) = 3A26h FREE INIT = SWITCH(1) LOC(2-1) 00 INIT = SWITCH(1) LOC(4) 0 PORT = 3A20h-3A3Fh SIZE = BYTE ;---------------------------------------------------------------------------- SUBFUNCTION = "Remoteboot support" HELP = "Enable this option to allow your computer to boot using network software stored in the EEPROM on the adaptor card. When enabled, the adapter will use the memory address range associated with it's I/O address. Make sure an I/O address range with memory enabled is selected elsewhere in this EISA configuration utility.\n" CHOICE = "Disabled" FREE INIT = SWITCH(1) LOC(3) 0b CHOICE = "Enabled" FREE INIT = SWITCH(1) LOC(3) 1b ;---------------------------------------------------------------------------- SUBFUNCTION = "MMIO support" HELP = "Enable this option to allow your adapter to use MMIO data transfers. This improves the perfomance of the adapter card. When enabled, the adapter will use the memory address range associated with it's I/O address. Make sure an I/O address range with memory enabled is selected elsewhere in this EISA configuration utility.\n" CHOICE = "Disabled" FREE INIT = SWITCH(1) LOC(4) 0b CHOICE = "Enabled" FREE INIT = SWITCH(1) LOC(4) 1b ;---------------------------------------------------------------------------- SUBFUNCTION = "Bus timing" HELP = "This parameter selects the bus timing used. The normal setting should work correctly for most computers. The alternative setting should only be used if the card fails to respond with normal bus timing.\n" CHOICE = "Normal" FREE INIT = SWITCH(1) LOC(5) 1b CHOICE = "Alternative" FREE INIT = SWITCH(1) LOC(5) 0b ; ; ------------------------ end of !MDG1020.CFG ------------------------------ ;