;******************************************************************************
;*                                                                            *
;*  Madge Blue+ 16/4 ISA PnP Token Ring Adapter                               *
;*      Adapter Configuration File  Version 1.0                               *
;*          Copyright (C) 1994 Madge Networks                                 *
;*                                                                            *
;******************************************************************************

BOARD
  ID            = "MDG2010"
  NAME          = "Madge Blue+ 16/4 ISA PnP Token Ring Adapter"
  MFR           = "Madge Networks Ltd."
  CATEGORY      = "NET"
  SLOT          = ISA16
  LENGTH        = 213
  AMPERAGE      = 1000
  SKIRT         = NO
  READID        = NO
  IOCHECK       = INVALID
  DISABLE       = UNSUPPORTED

  COMMENTS      = "The Madge Blue+ 16/4 ISA PnP Token Ring Adapter may
                   be used in ISA and EISA bus computers. \n\nThe EISA
                   configuration utility supplied with your computer will
                   identify a conflict free configuration of system resources
                   for this adapter. If you are going to use soft
                   configuration, (either because this is a non-PnP machine or
                   you have explicitly decided to disable PnP), then use the
                   supplied adapter configuration program to set the soft
                   configuration as suggested.\n\nNOTE: Adapter configuration
                   changes only take effect following a power ON/OFF cycle."


FUNCTION        = "Madge Blue+ 16/4 ISA PnP adapter"
  TYPE          = "NET"


  SUBFUNCTION   = "Alternate/Primary Adapter"
    COMMENTS    = "Up to two Madge Blue+ 16/4 ISA PnP Token Ring adapters may
                   be installed within a single computer. With multiple
                   adapters installed, one adapter MUST be designated as the
                   primary adapter, with the other set as the alternate
                   adapter. If only one adapter is installed, it should be set
                   to be a primary adapter. The factory default setting is
                   primary adapter."

    CHOICE      = "Primary"
     FREE
       PORT             = 0a20h-0a23h
	SHARE   = NO
       PORT             = 0a28h-0a2bh
	SHARE   = NO
       PORT             = 0a30h-0a33h
	SHARE   = NO
       PORT             = 0a38h-0a3bh
	SHARE   = NO

    CHOICE      = "Alternate"
      FREE
	PORT    = 0a24h-0a27h
	  SHARE = NO
	PORT    = 0a2ch-0a2fh
	  SHARE = NO
	PORT    = 0a34h-0a37h
	  SHARE = NO
	PORT    = 0a3ch-0a3fh
	  SHARE = NO


  SUBFUNCTION   = "ROM Address Location"
    COMMENTS    = "The factory default ROM address location for the adapter
		   is CC000-CDFFF."

    CHOICE      = "CC000-CDFFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0cc000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "CE000-CFFFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0ce000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "D0000-D1FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0d0000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "D2000-D3FFF"
    LINK        
     MEMORY     = 8K
	ADDRESS = 0d2000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "D4000-D5FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0d4000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "D6000-D7FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0d6000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "D8000-D9FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0d8000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "DA000-DBFFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0da000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "DC000-DDFFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0dc000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "DE000-DFFFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0de000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO


    CHOICE      = "C0000-C1FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0c0000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "C2000-C3FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0c2000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "C4000-C5FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0c4000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "C6000-C7FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0c6000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "C8000-C9FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0c8000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "CA000-CBFFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0cA000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

  SUBFUNCTION   = "Interrupt Level"
    COMMENTS    = "The Madge Blue+ 16/4 ISA PnP Token Ring Network Adapter can 
    		   operate on one of four interrupt levels in IBM-compatible
    		   mode: 2(9), 3, 10 and 11. In addition, if you are
    		   going to use Blue+ drivers you can set the card to
    		   interrupt levels 6, 7, 12 and 15.  NOTE: Interrupt level 6
    		   is used by the disk drive. If you have a disk drive present
    		   do not set your adapter card to  level 6 so as to avoid
    		   resource conflicts. The factory default setting is Interrupt
    		   2(9)."

    CHOICE      = "Interrupt 2 (9)"
    LINK 
      IRQ       = 9
	SHARE   = NO
	TRIGGER = EDGE
      

    CHOICE      = "Interrupt 3"
    LINK 
      IRQ       = 3
	SHARE   = NO
	TRIGGER = EDGE

    CHOICE      = "Interrupt 10"
    LINK 
      IRQ       = 10
	SHARE   = NO
	TRIGGER = EDGE

    CHOICE      = "Interrupt 11"
    LINK 
      IRQ       = 11
	SHARE   = NO
	TRIGGER = EDGE

    CHOICE      = "Interrupt 6 (Blue+ drivers only)"
    LINK 
      IRQ       = 6 
      SHARE   = NO 
      TRIGGER = EDGE

    CHOICE      = "Interrupt 7 (Blue+ drivers only)"
    LINK 
      IRQ       = 7
	SHARE   = NO
	TRIGGER = EDGE

    CHOICE      = "Interrupt 12 (Blue+ drivers only)"
    LINK 
      IRQ       = 12
	SHARE   = NO
	TRIGGER = EDGE

    CHOICE      = "Interrupt 15 (Blue+ drivers only)"
    LINK 
      IRQ       = 15
	SHARE   = NO
	TRIGGER = EDGE


  SUBFUNCTION   = "Shared RAM Size/Location"
    COMMENTS    = "The factory default RAM size is 16KB, and the 
		   default shared RAM address is D8000. There is an
		   additional special mode available when using Blue+
		   drivers in Fastblue mode where the Shared Ram may be
		   considered to be overlapped with the ROM area.  To
		   change the shared RAM address, use the Edit/Change Resource
		   option."

    CHOICE      = "16 KB"
    FREE
      MEMORY    = 16k
	ADDRESS = 0d8000h | 0dc000h |
		  0c0000h | 0c4000h | 0c8000h | 0cc000h    |
		  0d0000h | 0d4000h 
	WRITABLE= YES
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "None (Blue+ drivers - FastBlue mode only)"
    FREE
      MEMORY    =  8k
	ADDRESS = 0cc000h | 0ce000h | 0d0000h | 0d2000h |
		  0d4000h | 0d6000h | 0d8000h | 0da000h | 
		  0dc000h | 0de000h | 0c0000h | 0c2000h |
		  0c4000h | 0c6000h | 0c8000h | 0ca000h 

   CHOICE      = "8  KB"
    FREE
      MEMORY    =  8k
	ADDRESS = 0d8000h | 0da000h | 0dc000h | 0de000h |
		  0c0000h | 0c2000h | 0c4000h | 0c6000h | 
		  0c8000h | 0ca000h | 0cc000h | 0ce000h |
		  0d0000h | 0d2000h | 0d4000h | 0d6000h 
		  
	WRITABLE= YES
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE        = "32 KB"
    FREE
      MEMORY    = 32k
	ADDRESS = 0d0000h | 0d8000h | 0c0000h | 0c8000h 
	WRITABLE= YES
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO

    CHOICE      = "64 KB"
    FREE
      MEMORY    = 64k
	ADDRESS = 0d0000h | 0c0000h
	WRITABLE= YES
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO