BOARD			;10/04 MET New, 11/17 fcm Chg
 ID="MET1104"
 NAME="Metheus UGA 1104 Graphics Controller"
 MFR="Metheus"
 CATEGORY="VID"
 SLOT=ISA8
 LENGTH=165
 READID=YES
 COMMENTS="\n
The Metheus 1104 Ultra Graphics Accelerator\n\n
This device requires software initialization. See 'Software
Program' description below, or refer to the installation manual."

JUMPER(1)=2
 NAME="J8I - Sync Select 1"
 JTYPE=INLINE
 REVERSE=YES
 LABEL=LOC(1^2 2^3)"H SYNC""COMP.SYNC"
 FACTORY=LOC(1^2) 1
 COMMENTS="\nThis jumper is located near the RGB output connector on
 the right side of the board. Horizontal sync is selected
 by connecting the two left pins. Composite sync is selected
 by connecting the two right pins."

JUMPER(2)=1
 NAME="J8J - Sync Select 2"
 JTYPE=INLINE
 REVERSE=NO
 LABEL=LOC(2^1)"V SYNC"
 FACTORY=LOC(2^1) 1
 COMMENTS="\nThis jumper is located near the RGB output connector on
 the right side of the board. Vertical sync is selected
 by connecting the two pins. Disable by removing this
 jumper"

JUMPER(3)=2
 NAME="J8L - Monitor Sel 1"
 JTYPE=INLINE 
 REVERSE=YES
 LABEL=LOC(1^2 2^3)"interlace""non-inter."
 FACTORY=LOC(1^2 2^3) 10
 COMMENTS="\nThis jumper is located on the right side of the board. 
 Non-interlaced is selected by connecting the two left pins. 
 Interlaced is selcted by connecting the two right pins. 
 This jumper must also be moved with jumper J8M."

JUMPER(4)=2
 NAME="J8M - Monitor Sel 2"
 JTYPE=INLINE 
 REVERSE=YES
 LABEL=LOC(1^2 2^3)"interlace""non-inter"
 FACTORY=LOC(1^2 2^3) 10
 COMMENTS="\nThis jumper is located on the right side of the board. 
 Non-interlaced is selected by connecting the two left pins. 
 Interlaced is selcted by connecting the two right pins. 
 This jumper must also be moved with jumper J8L."

JUMPER(5)=5
 NAME="J8K - CGA Emulation"
 JTYPE=PAIRED 
 VERTICAL=YES
 REVERSE=YES
 LABEL=LOC(1-5)"reserved""reserved""reserved""reserved""CGA emu"
 FACTORY=LOC(5) 1
 COMMENTS="\nConnecting these two pins will enable CGA emulation. Remove
 this jumper to disable CGA emulation."

SOFTWARE(1)="\nThis graphics controller requires installation of a device
 driver entry in the 'CONFIG.SYS' file.\n\n
 By using the INSTALL program that comes with the Metheus
 microcode diskette, this can be installed for you 
 automatically.\n
 \n
 To manually install the UGA 1104 device driver, add the
 following entry to the 'CONFIG.SYS' file:\n
 \n
 'DEVICE=[C:path\\]1104.SYS'\n\n "

SOFTWARE(2)="\nIt is recommended that an entry be placed in the
 'AUTOEXEC.BAT' file, to initialize the device automatically
 as part of the system boot procedures.\n\n
 By using the INSTALL program that comes with the Metheus
 microcode diskette, this can be installed for you 
 automatically.\n\n
 The following line should be added to the 'AUTOEXEC.BAT' 
 file:\n\n
 'CD [path to Metheus files]'\n
 'GPLOAD [C:path\\]1104.BIN [c:path\\]8x16.FNT'\n"

SOFTWARE(3)="\nFor additional information, first consult:\n
 UGA 1104 Ultra Graphics Accelerator User's Guide\n\n
 Additional technical support is available where you purchased 
 your Metheus Product.\n\n
 Metheus Corporation\n
 OGC Science Park\n
 1600 NW Compton Dr.\n
 Beaverton, OR 97006\n
 503)690-1550\n"

FUNCTION="high resolution graphics"
 CHOICE="always enabled"
 free
 PORT=210h-214h
 PORT=220h-221h

FUNCTION="Sync Select 1"
 TYPE="VID"
 CHOICE="H Sync"
 free
 INIT=JUMPER(1) LOC(1^2) 1
 INIT=JUMPER(1) LOC(2^3) 0
 CHOICE="Composite Sync"
            
 FREE
 INIT=JUMPER(1) LOC(1^2) 0
 INIT=JUMPER(1) LOC(2^3) 1

FUNCTION="Sync Select 2"
 TYPE="VID"
 CHOICE="V Sync"
 free
 INIT=JUMPER(2) LOC(1^2) 1
 CHOICE="disable"
            
 FREE
 INIT=JUMPER(2) LOC(1^2) 0

FUNCTION="Monitor Select"
 TYPE="VID"
 CHOICE="Interlaced"
 free
 INIT=JUMPER(3) LOC(1^2 2^3) 10
 INIT=JUMPER(4) LOC(1^2 2^3) 10
 CHOICE="Non-Interlaced"
            
 FREE
 INIT=JUMPER(3) LOC(1^2 2^3) 01
 INIT=JUMPER(4) LOC(1^2 2^3) 01


FUNCTION="CGA Emulation"
 TYPE="VID,CGA"
 CHOICE="CGA Emulation"
 free
 INIT=JUMPER(5) LOC(5) 1
 PORT=3D0h - 3DFh
 link
 MEMORY=4000h
 ADDRESS=0B8000h
 MEMTYPE=OTH
 link
 MEMORY=64K
 ADDRESS=0A0000h
 MEMTYPE=OTH
 CHOICE="disable"
            
 FREE
 INIT=JUMPER(5) LOC(5) 0