;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;  NEC   System config file for   ***** A95 *****
;   Rev 1.25   31 Mar 1994 10:29:54   kfh
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
BOARD
ID="NEC1A01"
NAME="NEC Express/II P60ST System Board"
MFR="NEC"
CATEGORY="SYS"
SLOT=EMB(0)
READID=YES
COMMENTS="The NEC Express/II P60ST contains a 66MHz Pentium
CPU, 6 EISA slots, 1 Embedded EISA slot and 2 PCI slots."
HELP="This is the Board Identification Block help field
for the NEC Express/II P60ST System board."
SYSTEM
NONVOLATILE=7680 ;8192-256-256 BIOS scratch
AMPERAGE=31500
SLOT(1)=EISA(1) LENGTH=341 SKIRT=YES BUSMASTER=YES
SLOT(2)=EISA(2) LENGTH=341 SKIRT=YES BUSMASTER=YES
SLOT(3)=EISA(3) LENGTH=341 SKIRT=NO BUSMASTER=YES
SLOT(4)=EISA(4) LENGTH=341 SKIRT=NO BUSMASTER=YES
SLOT(5)=EISA(5) LENGTH=341 SKIRT=NO BUSMASTER=YES
SLOT(6)=EISA(6) LENGTH=341 SKIRT=NO BUSMASTER=YES
SLOT(7)=EISA(7),"Internal" BUSMASTER=YES LABEL="SCSI " LENGTH=1 SKIRT=NO
MEMORY=640k ADDRESS=00000000h CACHE=YES STEP=64K
MEMORY=64k ADDRESS=000F0000h CACHE=YES STEP=64K
;;MEMORY=65535k ADDRESS=00100000h CACHE=YES STEP=1M ;1M
;; NO check cache at 15 meg gap
MEMORY=14M ADDRESS=00100000h CACHE=YES STEP=1M
;;MEMORY=1M  ADDRESS=00F00000h CACHE=NO
MEMORY=49M ADDRESS=01000000h CACHE=YES STEP=1M
MEMORY=65535k ADDRESS=04100000h CACHE=YES STEP=1M ;64M
MEMORY=65535k ADDRESS=08100000h CACHE=YES STEP=1M ;128M
MEMORY=65535k ADDRESS=0C100000h CACHE=YES STEP=1M ;192M

SWITCH(1)=6
NAME="6 BIT DIP SWITCH (SW3)"
STYPE=DIP
REVERSE=YES
VERTICAL=YES
LABEL=LOC(6-1) "CMOS"
"NETFLASH"
"FLASH"
"PASSWORD"
"FLOPPY"
"VGA"
FACTORY=LOC(6-1) 000000
COMMENTS="VGA ON disables built-in VGA controller.\n
FLOPPY ON disables built-in floppy controller.\n
PASSWORD ON disables the password function.\n
FLASH ON disables BIOS reprogramming capability.\n
NETFLASH ON enables flashing over a network.\n
CMOS ON clears CMOS settings on boot-up."
HELP="The 6 BIT DIP switch must be manually set according to
the your system configuration.  If these switches are not
set properly, some system devices may not operate properly
and/or the system will display error messages at boot time.
The switches cannot be read by the SCU.  For more information
about these switches or any other switches and jumpers on
the system board, refer to your System Reference Guide."
FUNCTION="Dummy System Type"
SHOW=NO
COMMENTS="This is only needed to fool the s/w into letting us put
the header at the top of the file"
HELP="None"
CHOICE="Dummy"
FREE
INIT=SWITCH(1) LOC(6) 0

FUNCTION="VidMem"
TYPE="MEM"
SHOW=NO
CHOICE="OK"
FREE
MEMORY=32K
ADDRESS=0C0000h
WRITABLE=NO
MEMTYPE=OTH

FUNCTION="ConvntMem"
TYPE="MEM"
SHOW=NO
CHOICE="OK"
FREE
MEMORY=640K
ADDRESS=0K
WRITABLE=YES
MEMTYPE=SYS
CACHE=YES

FUNCTION="SysBrdIRQs"
TYPE="QRI"
SHOW=NO
CHOICE="OK"
FREE
IRQ=0
IRQ=1
IRQ=6
IRQ=8
IRQ=13

INCLUDE="ISACMOS.OVL"