BOARD
	ID = "NICC205"
	NAME = "National Instruments GPIB-PCII Interface Board"
	MFR = "NATIONAL INSTR CORP"
	CATEGORY = "COM"
	SLOT = ISA8
	READID = NO
        LENGTH = 110                                 ;11.05cm = 4.35inches
        AMPERAGE = 490 			   	     ;0.490 Amps
        SKIRT = NO
	COMMENTS = "GPIB-PCII/IIA EISA Configuration file Version 2.0; 
                    For further information call
                    National Instruments at 1-800-433-3488."
	HELP = "Sorry, no help available."

SWITCH(1) = 9
	NAME = "Base I/O Address"
	STYPE = DIP
	VERTICAL = NO
	REVERSE = YES
	LABEL = LOC(1-9) "A3" "A4" "A5" "A6" "A7" "A8" "A9" "7210" "PCII"
	FACTORY = LOC(1-9) 000101000
	INITVAL = LOC(1-9) XXXXXXXX0                  ;set for PCII mode
	;Factory default is (A3,A4,A5,A7,A9)=1, (A6,A8)=0, Mode=7210,PCII
	COMMENTS = "The base I/O address is determined by the settings of the
		    board DIP switch (U2) positions 1-7. The factory setting is 
		    for base address 2B8h.  Position 8 switches the chip emulation
                    mode between 7210 and 9914.  Leave this switch in the 7210 position
                    for normal operation with NI driver software.  Position 9 switches
                    the board emulation mode between PCII and PCIIA.  For PCIIA mode,
                    use the PCIIA configuration file, !NICC105.CFG."


JUMPER(1) = 6
	NAME = "DMA (W2)"
	JTYPE = PAIRED
	VERTICAL = NO
	REVERSE = YES
	LABEL = LOC(1-6) "DACK1" "DRQ1" "DACK2" "DRQ2" "DACK3" "DRQ3"
	FACTORY = LOC(1-6) 110000
        ;Factory defaults - DACK1,DRQ1                                                             
	COMMENTS = "The DMA channel used is determined by this jumper.
		    Note that both the DRQ (request) and DACK (acknowledge) jumpers must
		    be set to the same channel if that channel is to be used."

		    
JUMPER(2) = 6
	NAME = "IRQ Level (W3)"
	JTYPE = PAIRED
	VERTICAL = NO
	REVERSE = YES
	LABEL = LOC(1-6) "IRQ2" "IRQ3" "IRQ4" "IRQ5" "IRQ6" "IRQ7"
	FACTORY = LOC(1-6) 000001
        ;Factory default is IRQ7 
	COMMENTS = "The IRQ level (2, 3, 4, 5, 6, or 7) is determined by this jumper."


FUNCTION = "GPIB-PCII Interface"
  SUBFUNCTION = "Base I/O Address"
	COMMENTS = "The base I/O address is selected through this subfunction.
                    Note that since this address uses negative
                    logic, if your screen or report shows you a binary
                    representation of the switch, the ones and zeroes will
                    be reversed.  The 'ON' and 'OFF' settings given by the
                    configuration utility are correct."
	HELP = "Sorry, no help available."
    CHOICE = "2B8"
      LINK
        PORT = 2B8h-2BFh
        INIT = SWITCH(1) LOC(1-7) 0001010
    CHOICE = "2C0"
      LINK
        PORT = 2C0h-2C7h
        INIT = SWITCH(1) LOC(1-7) 1110010
    CHOICE = "100"
      LINK
        PORT = 100h-107h
        INIT = SWITCH(1) LOC(1-7) 1111101
    CHOICE = "108"
      LINK
        PORT = 108h-10Fh
        INIT = SWITCH(1) LOC(1-7) 0111101
    CHOICE = "110"
      LINK
        PORT = 110h-117h
        INIT = SWITCH(1) LOC(1-7) 1011101
    CHOICE = "118"
      LINK
        PORT = 118h-11Fh
        INIT = SWITCH(1) LOC(1-7) 0011101
    CHOICE = "120"
      LINK
        PORT = 120h-127h
        INIT = SWITCH(1) LOC(1-7) 1101101
    CHOICE = "128"
      LINK
        PORT = 128h-12Fh
        INIT = SWITCH(1) LOC(1-7) 0101101
    CHOICE = "130"
      LINK
        PORT = 130h-137h
        INIT = SWITCH(1) LOC(1-7) 1001101
    CHOICE = "138"
      LINK
        PORT = 138h-13Fh
        INIT = SWITCH(1) LOC(1-7) 0001101
    CHOICE = "140"
      LINK
        PORT = 140h-147h
        INIT = SWITCH(1) LOC(1-7) 1110101
    CHOICE = "148"
      LINK
        PORT = 148h-14Fh
        INIT = SWITCH(1) LOC(1-7) 0110101
    CHOICE = "150"
      LINK
        PORT = 150h-157h
        INIT = SWITCH(1) LOC(1-7) 1010101
    CHOICE = "158"
      LINK
        PORT = 158h-15Fh
        INIT = SWITCH(1) LOC(1-7) 0010101
    CHOICE = "160"
      LINK
        PORT = 160h-167h
        INIT = SWITCH(1) LOC(1-7) 1100101
    CHOICE = "168"
      LINK
        PORT = 168h-16Fh
        INIT = SWITCH(1) LOC(1-7) 0100101
    CHOICE = "170"
      LINK
        PORT = 170h-177h
        INIT = SWITCH(1) LOC(1-7) 1000101
    CHOICE = "178"
      LINK
        PORT = 178h-17Fh
        INIT = SWITCH(1) LOC(1-7) 0000101
    CHOICE = "180"
      LINK
        PORT = 180h-187h
        INIT = SWITCH(1) LOC(1-7) 1111001
    CHOICE = "188"
      LINK
        PORT = 188h-18Fh
        INIT = SWITCH(1) LOC(1-7) 0111001
    CHOICE = "190"
      LINK
        PORT = 190h-197h
        INIT = SWITCH(1) LOC(1-7) 1011001
    CHOICE = "198"
      LINK
        PORT = 198h-19Fh
        INIT = SWITCH(1) LOC(1-7) 0011001
    CHOICE = "1A0"
      LINK
        PORT = 1A0h-1A7h
        INIT = SWITCH(1) LOC(1-7) 1101001
    CHOICE = "1A8"
      LINK
        PORT = 1A8h-1AFh
        INIT = SWITCH(1) LOC(1-7) 0101001
    CHOICE = "1B0"
      LINK
        PORT = 1B0h-1B7h
        INIT = SWITCH(1) LOC(1-7) 1001001
    CHOICE = "1B8"
      LINK
        PORT = 1B8h-1BFh
        INIT = SWITCH(1) LOC(1-7) 0001001
    CHOICE = "1C0"
      LINK
        PORT = 1C0h-1C7h
        INIT = SWITCH(1) LOC(1-7) 1110001
    CHOICE = "1C8"
      LINK
        PORT = 1C8h-1CFh
        INIT = SWITCH(1) LOC(1-7) 0110001
    CHOICE = "1D0"
      LINK
        PORT = 1D0h-1D7h
        INIT = SWITCH(1) LOC(1-7) 1010001
    CHOICE = "1D8"		  
      LINK
        PORT = 1D8h-1DFh
        INIT = SWITCH(1) LOC(1-7) 0010001
    CHOICE = "1E0"
      LINK
        PORT = 1E0h-1E7h
        INIT = SWITCH(1) LOC(1-7) 1100001
    CHOICE = "1E8"
      LINK
        PORT = 1E8h-1EFh
        INIT = SWITCH(1) LOC(1-7) 0100001
    CHOICE = "1F0"
      LINK
        PORT = 1F0h-1F7h
        INIT = SWITCH(1) LOC(1-7) 1000001
    CHOICE = "1F8"
      LINK
        PORT = 1F8h-1FFh
        INIT = SWITCH(1) LOC(1-7) 0000001
    CHOICE = "200"
      LINK
        PORT = 200h-207h
        INIT = SWITCH(1) LOC(1-7) 1111110
    CHOICE = "208"
      LINK
        PORT = 208h-20Fh
        INIT = SWITCH(1) LOC(1-7) 0111110
    CHOICE = "210"
      LINK
        PORT = 210h-217h
        INIT = SWITCH(1) LOC(1-7) 1011110
    CHOICE = "218"
      LINK
        PORT = 218h-21Fh
        INIT = SWITCH(1) LOC(1-7) 0011110
    CHOICE = "220"
      LINK
        PORT = 220h-227h
        INIT = SWITCH(1) LOC(1-7) 1101110
    CHOICE = "228"
      LINK
        PORT = 228h-22Fh
        INIT = SWITCH(1) LOC(1-7) 0101110
    CHOICE = "230"
      LINK
        PORT = 230h-237h
        INIT = SWITCH(1) LOC(1-7) 1001110
    CHOICE = "238"
      LINK
        PORT = 238h-23Fh
        INIT = SWITCH(1) LOC(1-7) 0001110
    CHOICE = "240"
      LINK
        PORT = 240h-247h
        INIT = SWITCH(1) LOC(1-7) 1110110
    CHOICE = "248"
      LINK
        PORT = 248h-24Fh
        INIT = SWITCH(1) LOC(1-7) 0110110
    CHOICE = "250"
      LINK
        PORT = 250h-257h
        INIT = SWITCH(1) LOC(1-7) 1010110
    CHOICE = "258"
      LINK
        PORT = 258h-25Fh
        INIT = SWITCH(1) LOC(1-7) 0010110
    CHOICE = "260"
      LINK
        PORT = 260h-267h
        INIT = SWITCH(1) LOC(1-7) 1100110
    CHOICE = "268"
      LINK
        PORT = 268h-26Fh
        INIT = SWITCH(1) LOC(1-7) 0100110
    CHOICE = "270"
      LINK
        PORT = 270h-277h
        INIT = SWITCH(1) LOC(1-7) 1000110
    CHOICE = "278"
      LINK
        PORT = 278h-27Fh
        INIT = SWITCH(1) LOC(1-7) 0000110
    CHOICE = "280"
      LINK
        PORT = 280h-287h
        INIT = SWITCH(1) LOC(1-7) 1111010
    CHOICE = "288"
      LINK
        PORT = 288h-28Fh
        INIT = SWITCH(1) LOC(1-7) 0111010
    CHOICE = "290"
      LINK
        PORT = 290h-297h
        INIT = SWITCH(1) LOC(1-7) 1011010
    CHOICE = "298"
      LINK
        PORT = 298h-29Fh
        INIT = SWITCH(1) LOC(1-7) 0011010
    CHOICE = "2A0"
      LINK
        PORT = 2A0h-2A7h
        INIT = SWITCH(1) LOC(1-7) 1101010
    CHOICE = "2A8"
      LINK
        PORT = 2A8h-2AFh
        INIT = SWITCH(1) LOC(1-7) 0101010
    CHOICE = "2B0"
      LINK
        PORT = 2B0h-2B7h
        INIT = SWITCH(1) LOC(1-7) 1001010
    CHOICE = "2C8"
      LINK
        PORT = 2C8h-2CFh
        INIT = SWITCH(1) LOC(1-7) 0110010
    CHOICE = "2D0"
      LINK
        PORT = 2D0h-2D7h
        INIT = SWITCH(1) LOC(1-7) 1010010
    CHOICE = "2D8"		 
      LINK
        PORT = 2D8h-2DFh
        INIT = SWITCH(1) LOC(1-7) 0010010
    CHOICE = "2E0"
      LINK
        PORT = 2E0h-2E7h
        INIT = SWITCH(1) LOC(1-7) 1100010
    CHOICE = "2E8"
      LINK
        PORT = 2E8h-2EFh
        INIT = SWITCH(1) LOC(1-7) 0100010
    CHOICE = "2F0"
      LINK
        PORT = 2F0h-2F7h
        INIT = SWITCH(1) LOC(1-7) 1000010
    CHOICE = "2F8"
      LINK
        PORT = 2F8h-2FFh
        INIT = SWITCH(1) LOC(1-7) 0000010
    CHOICE = "300"
      LINK
        PORT = 300h-307h
        INIT = SWITCH(1) LOC(1-7) 1111100
    CHOICE = "308"
      LINK
        PORT = 308h-30Fh
        INIT = SWITCH(1) LOC(1-7) 0111100
    CHOICE = "310"
      LINK
        PORT = 310h-317h
        INIT = SWITCH(1) LOC(1-7) 1011100
    CHOICE = "318"
      LINK
        PORT = 318h-31Fh
        INIT = SWITCH(1) LOC(1-7) 0011100
    CHOICE = "320"
      LINK
        PORT = 320h-327h
        INIT = SWITCH(1) LOC(1-7) 1101100
    CHOICE = "328"
      LINK
        PORT = 328h-32Fh
        INIT = SWITCH(1) LOC(1-7) 0101100
    CHOICE = "330"
      LINK
        PORT = 330h-337h
        INIT = SWITCH(1) LOC(1-7) 1001100
    CHOICE = "338"
      LINK
        PORT = 338h-33Fh
        INIT = SWITCH(1) LOC(1-7) 0001100
    CHOICE = "340"
      LINK
        PORT = 340h-347h
        INIT = SWITCH(1) LOC(1-7) 1110100
    CHOICE = "348"
      LINK
        PORT = 348h-34Fh
        INIT = SWITCH(1) LOC(1-7) 0110100
    CHOICE = "350"
      LINK
        PORT = 350h-357h
        INIT = SWITCH(1) LOC(1-7) 1010100
    CHOICE = "358"
      LINK
        PORT = 358h-35Fh
        INIT = SWITCH(1) LOC(1-7) 0010100
    CHOICE = "360"
      LINK
        PORT = 360h-367h
        INIT = SWITCH(1) LOC(1-7) 1100100
    CHOICE = "368"
      LINK
        PORT = 368h-36Fh
        INIT = SWITCH(1) LOC(1-7) 0100100
    CHOICE = "370"
      LINK
        PORT = 370h-377h
        INIT = SWITCH(1) LOC(1-7) 1000100
    CHOICE = "378"
      LINK
        PORT = 378h-37Fh
        INIT = SWITCH(1) LOC(1-7) 0000100
    CHOICE = "380"
      LINK
        PORT = 380h-387h
        INIT = SWITCH(1) LOC(1-7) 1111000
    CHOICE = "388"
      LINK
        PORT = 388h-38Fh
        INIT = SWITCH(1) LOC(1-7) 0111000
    CHOICE = "390"
      LINK
        PORT = 390h-397h
        INIT = SWITCH(1) LOC(1-7) 1011000
    CHOICE = "398"
      LINK
        PORT = 398h-39Fh
        INIT = SWITCH(1) LOC(1-7) 0011000
    CHOICE = "3A0"
      LINK
        PORT = 3A0h-3A7h
        INIT = SWITCH(1) LOC(1-7) 1101000
    CHOICE = "3A8"
      LINK
        PORT = 3A8h-3AFh
        INIT = SWITCH(1) LOC(1-7) 0101000
    CHOICE = "3B0"
      LINK
        PORT = 3B0h-3B7h
        INIT = SWITCH(1) LOC(1-7) 1001000
    CHOICE = "3B8"
      LINK
        PORT = 3B8h-3BFh
        INIT = SWITCH(1) LOC(1-7) 0001000
    CHOICE = "3C0"
      LINK
        PORT = 3C0h-3C7h
        INIT = SWITCH(1) LOC(1-7) 1110000
    CHOICE = "3C8"
      LINK
        PORT = 3C8h-3CFh
        INIT = SWITCH(1) LOC(1-7) 0110000
    CHOICE = "3D0"
      LINK
        PORT = 3D0h-3D7h
        INIT = SWITCH(1) LOC(1-7) 1010000
    CHOICE = "3D8"		 
      LINK
        PORT = 3D8h-3DFh
        INIT = SWITCH(1) LOC(1-7) 0010000
    CHOICE = "3E0"
      LINK
        PORT = 3E0h-3E7h
        INIT = SWITCH(1) LOC(1-7) 1100000
    CHOICE = "3E8"
      LINK
        PORT = 3E8h-3EFh
        INIT = SWITCH(1) LOC(1-7) 0100000
    CHOICE = "3F0"
      LINK
        PORT = 3F0h-3F7h
        INIT = SWITCH(1) LOC(1-7) 1000000
    CHOICE = "3F8"
      LINK
        PORT = 3F8h-3FFh
        INIT = SWITCH(1) LOC(1-7) 0000000


  SUBFUNCTION = "DMA Channel"
    CHOICE = "1"
      LINK
        DMA = 1
        INIT = JUMPER(1) LOC(1-6) 110000
    CHOICE = "2"
      LINK
        DMA = 2
        INIT = JUMPER(1) LOC(1-6) 001100
    CHOICE = "3"
      LINK
        DMA = 3
        INIT = JUMPER(1) LOC(1-6) 000011
    CHOICE = "Disabled"
      LINK
        INIT = JUMPER(1) LOC(1-6) 000000


  SUBFUNCTION = "Interrupt Request Line"
    CHOICE = "7"
      LINK
        IRQ = 7
        SHARE = YES
        INIT = JUMPER(2) LOC(1-6) 000001
        INIT = SWITCH(1) LOC(1-3) 000
    CHOICE = "2"
      LINK
        IRQ = 2
        SHARE = YES
        INIT = JUMPER(2) LOC(1-6) 100000
        INIT = SWITCH(1) LOC(1-3) 101
    CHOICE = "3"
      LINK
        IRQ = 3
        SHARE = YES
        INIT = JUMPER(2) LOC(1-6) 010000
        INIT = SWITCH(1) LOC(1-3) 001
    CHOICE = "4"
      LINK
        IRQ = 4
        SHARE = YES
        INIT = JUMPER(2) LOC(1-6) 001000
        INIT = SWITCH(1) LOC(1-3) 110
    CHOICE = "5"
      LINK
        IRQ = 5
        SHARE = YES
        INIT = JUMPER(2) LOC(1-6) 000100
        INIT = SWITCH(1) LOC(1-3) 010
    CHOICE = "6"
      LINK
        IRQ = 6
        SHARE = YES
        INIT = JUMPER(2) LOC(1-6) 000010
        INIT = SWITCH(1) LOC(1-3) 100
    CHOICE = "Disabled"
      LINK
        INIT = JUMPER(2) LOC(1-6) 000000
        INIT = SWITCH(1) LOC(1-3) 111