; PLX EISA FDDI ADAPTER F9000-F1 (Rochester):Rev.C2,Rev.C3
; PC Fab. Rev. C
; (C)Copyright PLX Technology, 1993
;    All Rights Reserved.
;
; 1/27/93: (Rev.1)
; 4/21/93: (Rev.2)
BOARD
   ID = "PLX2101"                   ; EISA FDDI Adapter Rev 1 Product ID.
   NAME = "PLX EISA FDDI ADAPTER (F9000-F1) "
   MFR = "PLX TECHNOLOGY"           ; Manufacturere Name.
   CATEGORY = "NET"                 ; Category, i.e. Network Board.
   SLOT = EISA                                  ; Uses EISA Slot.
   LENGTH = 340                                 ; Length of Board in Millimeters.
   READID = yes                                 ; Board ID can be read
   BUSMASTER = 40                   ; Bus latency time allowed
   AMPERAGE = 2000                  ; Needs to be measured.
   IOCHECK = INVALID                ; Card will not respond to reads of 
				;  it's IOCHKERR bit.
   DISABLE = SUPPORTED              ; The card can be disabled by clearing
				;  the control register ENABLE bit.
   COMMENTS = " The FDDI EISA Board is a 32 bit FDDI Controller
		for the EISA bus.  The board supports the National
		FDDI Chip Set (BSI, MAC, PLAYER, CDD, CRD).
		The board is a bus master design that uses the host 
		system main memory directly.
		When receiving or transmitting packet data or during
		buffer management, the BSI requests the bus from the
		host system.  "

   HELP = "No help available."

IOPORT(1) = 0zc88h
	INITVAL = 11XX0XXX

IOPORT(2) = 0zc89h

IOPORT(3) = 0zc8Ah
	INITVAL = 00XXXXXX

IOPORT(4) = 0zc8Fh
	INITVAL = XXXXXXX0

SOFTWARE(1) =
"Debug software is in development."


;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

FUNCTION = "PLX EISA FDDI I/O Addresses"
   COMMENTS = "This board supports both slot-specific and ISA\n
		compatible I/O addressing.  The ISA mode should only\n
		be used for software compatibility with ISA drivers."
	      
      CHOICE = "Slot-Specific Only (Default)"
	FREE
	INIT = IOPORT(2) LOC(7-4) 0000

      CHOICE = "Slot-Specific and ISA"
	LINK
	INIT = IOPORT(2) LOC(7-4) 0001|0010|0101|0111|1001|1011|1101
	PORT = 100h-11Fh|120h-13fh|140h-15fh|160h-17fh|300h-31fh|
	       320h-32fh|340h-35fh


;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

FUNCTION = "Bus Master"

   SUBFUNCTION = "Bus Release After Preempt"

      CHOICE = "55 BCLK Cycles"
	FREE
	INIT = IOPORT(1) LOC(5) 1

   SUBFUNCTION = "Read Burst Enable"
      CHOICE = "Read Burst Enable" 
	FREE
        INIT = IOPORT(4) LOC(2) 1

   SUBFUNCTION = "Write Burst Enable"

      CHOICE = "Write Burst Enable" 
	FREE
        INIT = IOPORT(4) LOC(6) 1


;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

FUNCTION = "PLX EISA FDDI Interrupt"

      CHOICE = "Interrupt Level 10"
      LINK
	     IRQ = 10
         TRIGGER = EDGE
         SHARE = NO
         INIT = IOPORT(1) LOC(2-0) 001
         INIT = IOPORT(2) LOC(3-0) 0000

      CHOICE = "Interrupt Level 11"
      LINK
	     IRQ = 11
         TRIGGER = EDGE
         SHARE = NO
         INIT = IOPORT(1) LOC(2-0) 011
         INIT = IOPORT(2) LOC(3-0) 0000

      CHOICE = "Interrupt Level 12"
      LINK
	     IRQ = 12
         TRIGGER = EDGE
         SHARE = NO
         INIT = IOPORT(1) LOC(2-0) 101
         INIT = IOPORT(2) LOC(3-0) 0000

      CHOICE = "Interrupt Level 9"
      LINK
	     IRQ = 9
         TRIGGER = EDGE
         SHARE = NO
         INIT = IOPORT(1) LOC(2-0) 111
         INIT = IOPORT(2) LOC(3-0) 1011
    
      CHOICE = "Interrupt Level 5"
      LINK
	     IRQ = 5
         TRIGGER = EDGE
         SHARE = NO
         INIT = IOPORT(1) LOC(2-0) 111
         INIT = IOPORT(2) LOC(3-0) 1010

      CHOICE = "Interrupt Level 3"
      LINK
	     IRQ = 3
         TRIGGER = EDGE
         SHARE = NO
         INIT = IOPORT(1) LOC(2-0) 111
         INIT = IOPORT(2) LOC(3-0) 1001

 
      CHOICE = "Interrupt Level 15"
      LINK
	     IRQ = 15
         TRIGGER = EDGE
         SHARE = NO
         INIT = IOPORT(1) LOC(2-0) 111
         INIT = IOPORT(2) LOC(3-0) 1000