BOARD
  ID = "RTR8119"
  NAME = "Racore Token-Ring (16/4 Mbps, 16 bit ISA bus)"
  MFR = "Racore Computer Products"
  CATEGORY = "NET"
  SLOT = ISA16
  LENGTH = 193
  READID = NO
  COMMENTS = "\nThis is the Racore 16 bit ISA 16/4Mbps Token Ring network
              \nadapter for ISA and EISA bus compatible computers."

SWITCH(1) = 8
  NAME = "SW1 I/O-IRQ-MEM-DMA"
  STYPE = DIP
  VERTICAL = NO
  REVERSE = NO
  LABEL = LOC (1-8) "I/O-SW1" "I/O-SW2" "IRQ-SW3" "IRQ-SW4"
                    "MEM-SW5" "MEM-SW6" "DMA-SW7" "DMA-SW8"
  COMMENTS = "\nThis is the 8 position configuration DIP switch.
              \nPlease refer to the User Manual for more information."

FUNCTION = "16/4Mbps Token Ring Adapter"
  TYPE = "NET,TOK"

  SUBFUNCTION = "I/O Address Location"
    TYPE = "I/O"
    COMMENTS = "\nRacore supports up to four I/O address selections.
                \nThe preferred I/O address is 0A20h - 0A2Fh."

    CHOICE = "0A20h - 0A2Fh"
      LINK
        PORT = 0A20h-0A2Fh
          SHARE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(2 1) 10
    CHOICE = "0A00h - 0A0Fh"
      LINK
        PORT = 0A00h-0A0Fh
          SHARE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(2 1) 11
    CHOICE = "0A40h - 0A4Fh"
      LINK
        PORT = 0A40h-0A4Fh
          SHARE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(2 1) 01
    CHOICE = "0A60h - 0A6Fh"
      LINK
        PORT = 0A60h-0A6Fh
          SHARE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(2 1) 00

  SUBFUNCTION = "Interrupt (IRQ) Level"
    TYPE = "INT"
    COMMENTS = "\nRacore supports up to four IRQ level selections.
                \nThe preferred IRQ level is IRQ 2 (9)."

    CHOICE = "Interrupt 2 (9)"
    SUBTYPE = "9"
      LINK
        IRQ = 9
          SHARE = NO
          TRIGGER = EDGE
        INIT = SWITCH(1) LOC(4 3) 10
    CHOICE = "Interrupt 3"
    SUBTYPE = "3"
      LINK
        IRQ = 3
          SHARE = NO
          TRIGGER = EDGE
        INIT = SWITCH(1) LOC(4 3) 11
    CHOICE = "Interrupt 10"
    SUBTYPE = "10"
      LINK
        IRQ = 10
          SHARE = NO
          TRIGGER = EDGE
        INIT = SWITCH(1) LOC(4 3) 01
    CHOICE = "Interrupt 11"
    SUBTYPE = "11"
      LINK
        IRQ = 11
          SHARE = NO
          TRIGGER = EDGE
        INIT = SWITCH(1) LOC(4 3) 00

  SUBFUNCTION = "Memory (ROM) Address Location"
    TYPE = "ROM"
    COMMENTS = "\nRacore support up to four ROM address locations.
                \nThe preferred location is CC000-CFFFF."

    CHOICE = "CC000-CFFFF"
      LINK
        MEMORY = 16K
          ADDRESS = 0CC000h
          WRITABLE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(6 5) 11
    CHOICE = "D0000-D3FFF"
      LINK
        MEMORY = 16K
          ADDRESS = 0D0000h
          WRITABLE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(6 5) 10
    CHOICE = "D8000-DBFFF"
      LINK
        MEMORY = 16K
          ADDRESS = 0D8000h
          WRITABLE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(6 5) 01
    CHOICE = "DC000-DFFFF"
      LINK
        MEMORY = 16K
          ADDRESS = 0DC000h
          WRITABLE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(6 5) 00

  SUBFUNCTION = "DMA Channel Selection"
    TYPE = "DMA"
    COMMENTS = "\nRacore supports up to four DMA channel selections.
                \nThere is no preferred channel selection."

    CHOICE = "DMA Channel 0"
    SUBTYPE = "DMA0"
      LINK
        DMA = 0
          SHARE = NO
          TIMING = DEFAULT
        INIT = SWITCH(1) LOC(8 7) 11
    CHOICE = "DMA Channel 5"
    SUBTYPE = "DMA5"
      LINK
        DMA = 5
          SHARE = NO
          TIMING = DEFAULT
        INIT = SWITCH(1) LOC(8 7) 10
    CHOICE = "DMA Channel 6"
    SUBTYPE = "DMA6"
      LINK
        DMA = 6
          SHARE = NO
          TIMING = DEFAULT
        INIT = SWITCH(1) LOC(8 7) 01
    CHOICE = "DMA Channel 7"
    SUBTYPE = "DMA7"
      LINK
        DMA = 7
          SHARE = NO
          TIMING = DEFAULT
        INIT = SWITCH(1) LOC(8 7) 00

SWITCH(2) = 8
  NAME = "SW2 Adapter Control"
  STYPE = DIP
  VERTICAL = NO
  REVERSE = NO
  LABEL = LOC (1-8) "RPLEN-SW1" "SPEED-SW2" "MEDIA-SW3" "ROMEN-SW4"
                    "A13EN-SW5" "BURST-SW6" "CLOCK-SW7" "NC-SW8"
  COMMENTS = "\nThis is the 8 position configuration DIP switch.
              \nPlease refer to the User Manual for more information."

FUNCTION = "16/4Mbps Token Ring Adapter"
  TYPE = "NET, TOK"

  SUBFUNCTION = "RPL Enable/Disable"
    COMMENTS = "\nThe Racore adapter may RPL from either a NOVELL network
		\nor a PCNet network.  You may enable or disable this
		\nfunction depending on whether you wish to boot from a
                \nNetwork or from a local drive."
    CHOICE = "RPL Disabled"
      FREE
        INIT = SWITCH(2) LOC(1) 1
    CHOICE = "RPL Enabled"
      FREE
        INIT = SWITCH(2) LOC(1) 0

  SUBFUNCTION = "Adapter Data Rate (Ring Speed)"
    TYPE = "SPD"
    COMMENTS = "\nRacore offers both 4Mbps and 16Mbps Ring Speed.
                \nYou must set the speed to the same rate as the 
                \nLAN segment to which you are connecting."

    CHOICE = "16 Mbps"
    SUBTYPE = "16"
      FREE
        INIT = SWITCH(2) LOC(2) 1
    CHOICE = "4 Mbps"
    SUBTYPE = "4"
      FREE
        INIT = SWITCH(2) LOC(2) 0

  SUBFUNCTION = "Type 1 OR Type 3 Media Selection"
    COMMENTS = "\nRacore provides on-board connections to either Type 1
                \n(STP) or Type 3 (UTP) cable. You must select the
                \nappropriate cable, thus enabling the proper connector."

    CHOICE = "TYPE 1 (STP)"
      FREE
        INIT = SWITCH(2) LOC(3) 1
    CHOICE = "TYPE 3 (UTP)"
      FREE
        INIT = SWITCH(2) LOC(3) 0

  SUBFUNCTION = "ROM Space Enabled/Disabled"
    COMMENTS = "\nThis switch allocates ROM space for a BIA device.
                \nThis switch will normally be ON, disabled."

    CHOICE = "ROM Disabled"
      FREE
        INIT = SWITCH(2) LOC(4) 1
    CHOICE = "ROM Enabled"
      FREE
        INIT = SWITCH(2) LOC(4) 0

  SUBFUNCTION = "8 KByte OR 16 KByte PAGES"
    COMMENTS = "\nAllows the use of either an 8 KByte or 16 KByte pages."

    CHOICE = "8 KByte Page"
      FREE
        INIT = SWITCH(2) LOC(5) 1
    CHOICE = "16 KByte Page"
      FREE
        INIT = SWITCH(2) LOC(5) 0

  SUBFUNCTION = "Burst Mode Selection"
    COMMENTS = "\nAllows the adapter to function in a minimum or
                \nmaximum BURST packet transmission mode."

    CHOICE = "Maximum BURST"
      FREE
        INIT = SWITCH(2) LOC(6) 0

    CHOICE = "Minimum BURST"
      FREE
        INIT = SWITCH(2) LOC(6) 1

  SUBFUNCTION = "Adapter Processor Clock Speed"
    COMMENTS = "\nAllows the selection of either the System BCLK or the on
                \nboard 8 MHz clock for the adapter Processor to run at."

    CHOICE = "SYSTEM BUS CLOCK"
      FREE
        INIT = SWITCH(2) LOC(7) 0

    CHOICE = "8 MHz ON BOARD CLOCK"
      FREE
        INIT = SWITCH(2) LOC(7) 1