;-------------------------------------------------------------------------;
; UNISYS Corporation        SCP Serial 8 Port Controller       (Rev 1.06) ;
;-------------------------------------------------------------------------;
BOARD
; U6000/65 version
;  ID = "SCP6001"
; All other systems version
  ID = "SCP6000"

  NAME="UN6050-8IO (8 Port) SCP Communication Controller"
  MFR="UNISYS, San Jose"
  CATEGORY = "COM"
  SLOT = ISA16
  LENGTH = 330
  AMPERAGE = 4000
  SKIRT = NO
  READID = NO
; U6000/65 version
;  COMMENTS="The SCP Communication Controller contains two switches, where
;            SWITCH 1 controls (I/O Port) selection, and SWITCH 2 controls 
;            shared Interrupt (IRQ) selection. On the U6000/65 system,
;            SCP Controller numbers 1, 2 and 3 can be fitted in any
;            free slot. However, SCP Controller numbers 4, 5 and 6
;            MUST be fitted in slots 4, 5 and 6 respectively. Failure to
;            observe this rule will result in non operation of those
;            controllers."
; All other systems version
  COMMENTS="The SCP Communication Controller contains two switches, where
            SWITCH 1 controls (I/O Port) selection, and SWITCH 2 controls 
            shared Interrupt (IRQ) selection."

; SWITCH(1)
;
;       1      2      3      4      5      6      7      8      9      10
;    +------+------+------+------+------+------+------+------+------+------+
;    | bit9 | bit8 | bit7 | bit6 | bit5 | bit4 |  OFF |  OFF |  OFF |  OFF |
;    +------+------+------+------+------+------+------+------+------+------+
;       ON    OFF     ON     ON     ON     ON   - sets I/O BASE Address 100h
;
;    Note, the I/O BASE Address must be set to 100h so that the U6000/35 I/O
;          board and the SCP boards share the same base address.
;

SWITCH(1) = 10
  NAME = "SW1 (Base I/O Port)"
  STYPE = DIP
  VERTICAL = NO
  REVERSE = YES

; SWITCH(2)
;
;       1      2      3      4      5      6      7      8      9      10
;    +--------------------+------+------+------+------+------+------+------+
;    | Board Number (bits)| IRQ3 | IRQ5 | IRQ10| IRQ11| IRQ12| IRQ14| IRQ15|
;    +--------------------+------+------+------+------+------+------+------+
;      ON     ON     OFF (Board 1)
;      ON     OFF    ON  (Board 2)
;      ON     OFF    OFF (Board 3)

SWITCH(2) = 10
  NAME = "SW2 (IRQ selection)"
  STYPE = DIP
  VERTICAL = NO
  REVERSE = YES

SOFTWARE(1) ="\n\tSelected Resource Options: \n"

FUNCTION = "(SCP Board) Configuration Options"
   TYPE = "COM,ASY"
; U6000/65 version
;   CHOICE = "First SCP Board (IRQ=10, PORT=106h/500h-50Fh, MEM=128K/FC0000h)"
;      SUBTYPE="SCP0"
;      LINK
;         IRQ=10
;            SHARE = NO
;            TRIGGER = EDGE
;         INIT = SWITCH(1) LOC(1-10) 1011110000
;         INIT = SWITCH(2) LOC(1-3)  110
;         INIT = SWITCH(2) LOC(4-10) 0010000
;         INIT=software(1) "\tIRQ=10"
;      LINK
;         PORT=0106h
;            SHARE = NO
;            SIZE = BYTE
;         INIT=software(1) "\tBase Port=106h"
;         PORT=0500h-050Fh
;            SHARE = NO
;            SIZE = BYTE
;         INIT=software(1) "\tTTY I/O=500h-50Fh"
;      LINK
;         MEMORY = 128K
;         ADDRESS = 0FC0000h
;            WRITABLE = YES
;            MEMTYPE = OTH
;            SIZE = BYTE
;            DECODE = 24
;            CACHE = NO
;            SHARE = NO
;         INIT=software(1) "\tMEM=128K at FC0000"
;
;   CHOICE = "Second SCP Board (IRQ=11, PORT=108h/900h-90Fh, MEM=128K/FA0000h)"
;      SUBTYPE="SCP1"
;      LINK
;         IRQ=11
;            SHARE = NO
;            TRIGGER = EDGE
;         INIT = SWITCH(1) LOC(1-10) 1011110000
;         INIT = SWITCH(2) LOC(1-3)  101
;         INIT = SWITCH(2) LOC(4-10) 0001000
;         INIT=software(1) "\tIRQ=11"
;      LINK
;         PORT=0108h
;            SHARE = NO
;            SIZE = BYTE
;         INIT=software(1) "\tBase Port=108h"
;         PORT=0900h-090Fh
;            SHARE = NO
;            SIZE = BYTE
;         INIT=software(1) "\tTTY I/O=900h-90Fh"
;      LINK
;         MEMORY = 128K
;         ADDRESS = 0FA0000h
;            WRITABLE = YES
;            MEMTYPE = OTH
;            SIZE = BYTE
;            DECODE = 24
;            CACHE = NO
;            SHARE = NO
;         INIT=software(1) "\tMEM=128K at FA0000"
;
;   CHOICE = "Third SCP Board (IRQ=12, PORT=10Ah/D00h-D0Fh, MEM=128K/F80000h)"
;      SUBTYPE="SCP2"
;      LINK
;         IRQ=12
;            SHARE = NO
;            TRIGGER = EDGE
;         INIT = SWITCH(1) LOC(1-10) 1011110000
;         INIT = SWITCH(2) LOC(1-3)  100
;         INIT = SWITCH(2) LOC(4-10) 0000100
;         INIT=software(1) "\tIRQ=12"
;      LINK
;         PORT=010Ah
;            SHARE = NO
;            SIZE = BYTE
;         INIT=software(1) "\tBase Port=10Ah"
;         PORT=0D00h-0D0Fh
;            SHARE = NO
;            SIZE = BYTE
;         INIT=software(1) "\tTTY I/O=D00h-D0Fh"
;      LINK
;         MEMORY = 128K
;         ADDRESS = 0F80000h
;            WRITABLE = YES
;            MEMTYPE = OTH
;            SIZE = BYTE
;            DECODE = 24
;            CACHE = NO
;            SHARE = NO
;         INIT=software(1) "\tMEM=128K at F80000"
;
;   CHOICE = "Fourth SCP Board (IRQ=14, Port=44F0h/4480h-448Fh, Memory=128K/0F60000h)"
;      SUBTYPE="SCP3"
;      LINK
;         IRQ=14
;            SHARE = NO
;            TRIGGER = EDGE
;         INIT = SWITCH(1) LOC(1-10) 1011110000
;         INIT = SWITCH(2) LOC(1-3)  011
;         INIT = SWITCH(2) LOC(4-10) 0000010
;         INIT=software(1) "\tIRQ=14"
;      LINK
;         PORT=044F0h
;            SHARE = NO
;            SIZE = BYTE
;         INIT=software(1) "\tBase Port=44F0h"
;         PORT=04480h-0448Fh
;            SHARE = NO
;            SIZE = BYTE
;         INIT=software(1) "\tTTY I/O=04480h-0448Fh"
;      LINK
;         MEMORY = 128K
;         ADDRESS = 0F60000h
;            WRITABLE = YES
;            MEMTYPE = OTH
;            SIZE = BYTE
;            DECODE = 24
;            CACHE = NO
;            SHARE = NO
;         INIT=software(1) "\tMEM=128K at F60000"
;
;   CHOICE = "Fifth SCP Board (IRQ=15, Port=54F4/5490h-549Fh, Memory=128K/0F40000h)"
;      SUBTYPE="SCP4"
;      LINK
;         IRQ=15
;            SHARE = NO
;            TRIGGER = EDGE
;         INIT = SWITCH(1) LOC(1-10) 1011110000
;         INIT = SWITCH(2) LOC(1-3)  010
;         INIT = SWITCH(2) LOC(4-10) 0000001
;         INIT=software(1) "\tIRQ=15"
;      LINK
;         PORT=054F4h
;            SHARE = NO
;            SIZE = BYTE
;         INIT=software(1) "\tBase Port=54F4h"
;         PORT=05490h-0549Fh
;            SHARE = NO
;            SIZE = BYTE
;         INIT=software(1) "\tTTY I/O=5490h-549Fh"
;      LINK
;         MEMORY = 128K
;         ADDRESS = 0F40000h
;            WRITABLE = YES
;            MEMTYPE = OTH
;            SIZE = BYTE
;            DECODE = 24
;            CACHE = NO
;            SHARE = NO
;         INIT=software(1) "\tMEM=128K at F40000"
;
;   CHOICE = "Sixth SCP Board (IRQ=5, Port=64F8h/64A0h-64AFh, Memory=128K/0F20000h)"
;      SUBTYPE="SCP5"
;      LINK
;         IRQ=5
;            SHARE = NO
;            TRIGGER = EDGE
;         INIT = SWITCH(1) LOC(1-10) 1011110000
;         INIT = SWITCH(2) LOC(1-3)  001
;         INIT = SWITCH(2) LOC(4-10) 1000000
;         INIT=software(1) "\tIRQ=5"
;      LINK
;         PORT=064F8h
;            SHARE = NO
;            SIZE = BYTE
;         INIT=software(1) "\tBase Port=64F8h"
;         PORT=064A0h-064AFh
;            SHARE = NO
;            SIZE = BYTE
;         INIT=software(1) "\tTTY I/O=64A0h-64AFh"
;      LINK
;         MEMORY = 128K
;         ADDRESS = 0F20000h
;            WRITABLE = YES
;            MEMTYPE = OTH
;            SIZE = BYTE
;            DECODE = 24
;            CACHE = NO
;            SHARE = NO
;         INIT=software(1) "\tMEM=128K at F20000"

   CHOICE = "First SCP Board (IRQ=10, PORT=106h/500h-50Fh, MEM=128K/FC0000h)"
      SUBTYPE="SCP0"
      LINK
         IRQ=10
            SHARE = NO
            TRIGGER = EDGE
         INIT = SWITCH(1) LOC(1-10) 1011110000
         INIT = SWITCH(2) LOC(1-3)  110
         INIT = SWITCH(2) LOC(4-10) 0010000
         INIT=software(1) "\tIRQ=10"
      LINK
         PORT=0106h
            SHARE = NO
            SIZE = BYTE
         INIT=software(1) "\tBase Port=106h"
         PORT=0500h-050Fh
            SHARE = NO
            SIZE = BYTE
         INIT=software(1) "\tTTY I/O=500h-50Fh"
      LINK
         MEMORY = 128K
         ADDRESS = 0FC0000h
            WRITABLE = YES
            MEMTYPE = OTH
            SIZE = BYTE
            DECODE = 24
            CACHE = NO
            SHARE = NO
         INIT=software(1) "\tMEM=128K at FC0000"

   CHOICE = "Second SCP Board (IRQ=12, PORT=108h/900h-90Fh, MEM=128K/FA0000h)"
      SUBTYPE="SCP1"
      LINK
         IRQ=12
            SHARE = NO
            TRIGGER = EDGE
         INIT = SWITCH(1) LOC(1-10) 1011110000
         INIT = SWITCH(2) LOC(1-3)  101
         INIT = SWITCH(2) LOC(4-10) 0000100
         INIT=software(1) "\tIRQ=12"
      LINK
         PORT=0108h
            SHARE = NO
            SIZE = BYTE
         INIT=software(1) "\tBase Port=108h"
         PORT=0900h-090Fh
            SHARE = NO
            SIZE = BYTE
         INIT=software(1) "\tTTY I/O=900h-90Fh"
      LINK
         MEMORY = 128K
         ADDRESS = 0FA0000h
            WRITABLE = YES
            MEMTYPE = OTH
            SIZE = BYTE
            DECODE = 24
            CACHE = NO
            SHARE = NO
         INIT=software(1) "\tMEM=128K at FA0000"

   CHOICE = "Third SCP Board (IRQ=15, PORT=10Ah/D00h-D0Fh, MEM=128K/F80000h)"
      SUBTYPE="SCP2"
      LINK
         IRQ=15
            SHARE = NO
            TRIGGER = EDGE
         INIT = SWITCH(1) LOC(1-10) 1011110000
         INIT = SWITCH(2) LOC(1-3)  100
         INIT = SWITCH(2) LOC(4-10) 0000001
         INIT=software(1) "\tIRQ=15"
      LINK
         PORT=010Ah
            SHARE = NO
            SIZE = BYTE
         INIT=software(1) "\tBase Port=10Ah"
         PORT=0D00h-0D0Fh
            SHARE = NO
            SIZE = BYTE
         INIT=software(1) "\tTTY I/O=D00h-D0Fh"
      LINK
         MEMORY = 128K
         ADDRESS = 0F80000h
            WRITABLE = YES
            MEMTYPE = OTH
            SIZE = BYTE
            DECODE = 24
            CACHE = NO
            SHARE = NO
         INIT=software(1) "\tMEM=128K at F80000"

   CHOICE = "Free Format configuration for other SCP board setups"
      SUBTYPE="SCPX"
      LINK
         IRQ=10|12|15|14|11|5|3
            SHARE = NO
            TRIGGER = EDGE
         INIT = SWITCH(2) LOC(1-3)  110|101|100|011|010|001|000
         INIT = SWITCH(2) LOC(4-10) 0010000|0000100|0000001|0000010|0001000|0100000|1000000
         INIT=software(1)
              "\tIRQ=10"|"\tIRQ=12"|"\tIRQ=15"|"\tIRQ=14"|
              "\tIRQ=11"|"\tIRQ=5"|"\tIRQ=3"
      LINK
         PORT=0106h|0108h|010Ah|05F0h|05F4h|05F8h|05FCh
            SHARE = NO
            SIZE = BYTE
         INIT=software(1)
              "\tBase Port=106h"|"\tBase Port=108h"|"\tBase Port=10Ah"|
              "\tBase Port=5F0h"|"\tBase Port=5F4h"|"\tBase Port=5F8h"|
              "\tBase Port=5FCh"
         PORT=0500h-050Fh|0900h-090Fh|0D00h-0D0Fh|0580h-058Fh|0590h-059Fh|05A0h-05AFh|05B0h-05BFh
            SHARE = NO
            SIZE = BYTE
         INIT=software(1)
              "\tTTY I/O=500h-50Fh"|"\tTTY I/O=900h-90Fh"|
              "\tTTY I/O=D00h-D0Fh"|"\tTTY I/O=580h-58Fh"|
              "\tTTY I/O=590h-59Fh"|"\tTTY I/O=5A0h-5AFh"|
              "\tTTY I/O=5B0h-5BFh"
      LINK
         MEMORY = 128K|128K|128K|128K
         ADDRESS = 0FC0000h|0FA0000h|0F80000h|0F60000h
            WRITABLE = YES
            MEMTYPE = OTH
            SIZE = BYTE
            DECODE = 24
            CACHE = NO
            SHARE = NO
         INIT = SWITCH(1) LOC(1-10) 1011110000|1011110000|1011110000|1011110000
         INIT=software(1)
              "\tMEM=128K at FC0000"|"\tMEM=128K at FA0000"|
              "\tMEM=128K at F80000"|"\tMEM=128K at F60000"