;
; Star Gate Technologies Inc. - ACL IIR (64k)
;

BOARD
	ID="SGT0021"
	NAME="ACL IIR - Serial Card w/64k RAM"
	MFR="Star Gate"
	CATEGORY="COM"
	SLOT=ISA16
	LENGTH=330
	SKIRT=NO
	READID=NO
	COMMENTS="Star Gate ACL IIR with 64k dual port RAM."

SWITCH(1)=4
	NAME="SW1"
	STYPE=DIP
	VERTICAL=NO
	REVERSE=YES
	FACTORY=LOC(1-4) 0000
	COMMENTS="Positions 1 and 2 are used to set the board I/O
 latch addresses. Position 3 determines whether the board's Dual Port
will be mapped above or below the 1 Meg boundary."
	
SWITCH(2)=8
	NAME="SW2"
	STYPE=DIP
	VERTICAL=NO
	REVERSE=YES
	LABEL=LOC(1-8) "irq3" "irq4" "irq5" "irq9" "irq10" "irq11" "irq12" "irq15"
	FACTORY=LOC(1-8) 00000000
	COMMENTS="This switch is located just above the gold plated
 edge connector.  It is used to set the board IRQ level."
	
JUMPER(1)=8
	NAME="JMP2"
	JTYPE=PAIRED
	VERTICAL=NO
	REVERSE=YES
	LABEL=LOC(1-8) "1" "2" "3" "4" "5" "6" "7" "8"
	FACTORY=LOC(1-8) 10000000
	INITVAL=LOC(1-8) 01000000
	COMMENTS="This jumper is used to select the number of wait states
required by the host computer. Position 1 inserts zero wait states, position
2 selects one wait state, and so on. If you are using an 8 Mhz backplane it
is suggested that you set the jumper to position 2 for one wait state. "

FUNCTION="IRQ Level"
	TYPE="COM,ASY"
	COMMENTS=" The ACL IIR can be configured to use IRQs 3,4,5,9,10,11,12,15"

	CHOICE="irq 3"
		LINK
		IRQ=3
		SHARE=NO
		INIT=SWITCH(2) LOC(1-8) 10000000

	CHOICE="irq 4"
		LINK
		IRQ=4
		SHARE=NO
		INIT=SWITCH(2) LOC(1-8) 01000000

	CHOICE="irq 5"
		LINK
		IRQ=5
		SHARE=NO
		INIT=SWITCH(2) LOC(1-8) 00100000

	CHOICE="irq 9"
		LINK
		IRQ=9
		SHARE=NO
		INIT=SWITCH(2) LOC(1-8) 00010000

	CHOICE="irq 10"
		LINK
		IRQ=10
		SHARE=NO
		INIT=SWITCH(2) LOC(1-8) 00001000

	CHOICE="irq 11"
		LINK
		IRQ=11
		SHARE=NO
		INIT=SWITCH(2) LOC(1-8) 00000100

	CHOICE="irq 12"
		LINK
		IRQ=12
		SHARE=NO
		INIT=SWITCH(2) LOC(1-8) 00000010

	CHOICE="irq 15"
		LINK
		IRQ=15
		SHARE=NO
		INIT=SWITCH(2) LOC(1-8) 00000001

	CHOICE="Disabled"
		DISABLE = YES
		FREE
		INIT=SWITCH(2) LOC(1-8) 00000000

FUNCTION="Set I/O Latch Address"
	CHOICE="200h,204h"
		LINK
		PORT=0200h
		SHARE=NO
		SIZE=BYTE
		PORT=0204h
		SHARE=NO
		SIZE=BYTE
		INIT=SWITCH(1) LOC(1 2 3 4) 0000

	CHOICE="300h,304h"
		LINK
		PORT=0300h
		SHARE=NO
		SIZE=BYTE
		PORT=0304h
		SHARE=NO
		SIZE=BYTE
		INIT=SWITCH(1) LOC(1 2 3 4) 1000

	CHOICE="600h,604h"
		LINK
		PORT=0600h
		SHARE=NO
		SIZE=BYTE
		PORT=0604h
		SHARE=NO
		SIZE=BYTE
		INIT=SWITCH(1) LOC(1 2 3 4) 0100

	CHOICE="700h,704h"
		LINK
		PORT=0700h
		SHARE=NO
		SIZE=BYTE
		PORT=0704h
		SHARE=NO
		SIZE=BYTE
		INIT=SWITCH(1) LOC(1 2 3 4) 1100

FUNCTION="Dual Port RAM Address"
COMMENTS = "Select 'Change Resources' from the Edit pull-down
 menu to change the selections for this function.
\nSelect 'View Resources' to verify the selected addresses and IRQ
 lines.\n"
	CHOICE="Dual Port Address"
		LINK
		MEMORY=64K
		ADDRESS=0A0000h-0FF0000h STEP=64K
		WRITABLE=YES
		MEMTYPE=OTHER
		SHARE=NO