;
; Star Gate Technologies Inc. - ACL II (64k)
;

BOARD
	ID="SGT1101"
	NAME="ACL II - Serial Card w/64k RAM"
	MFR="Star Gate"
	CATEGORY="COM"
	SLOT=ISA16
	LENGTH=330
	SKIRT=NO
	READID=NO
	COMMENTS="Star Gate ACL II with 64k dual port RAM."
	HELP="Star Gate ACL II with 64k dual port RAM."

SWITCH(1)=8
	NAME="SW1"
	STYPE=DIP
	VERTICAL=NO
	REVERSE=YES
	FACTORY=LOC(1-8)00000000
	LABEL=LOC(1-8) "irq3" "irq4" "irq5" "irq9" "irq10" "irq11" "irq12" "irq15"
	COMMENTS="This switch is located just above the gold plated
 edge connector.  It is used to set the board IRQ level."
	HELP="This switch is located just above the gold plated
 edge connector.  It is used to set the board IRQ level."

	
SWITCH(2)=4
	NAME="SW2"
	STYPE=DIP
	VERTICAL=NO
	REVERSE=YES
	FACTORY=LOC(1-4)0000
	COMMENTS="This switch is located just above the gold plated
 edge connector.  Positions 1 and 2 are used to set the board I/O
 latch addresses. Position 3 determines whether the board's Dual Port
will be mapped above or below the 1 Meg boundary."
	HELP="This switch is located just above the gold plated
 edge connector.  Positions 1 and 2 are used to set the board I/O
 latch addresses. Position 3 determines whether the board's Dual Port
will be mapped above or below the 1 Meg boundary."

	
JUMPER(1)=8
	NAME="JP2"
	JTYPE=PAIRED
	VERTICAL=NO
	REVERSE=YES
	LABEL=LOC(1-8) "1" "2" "3" "4" "5" "6" "7" "8"
	FACTORY=LOC(1-8) 10000000
	INITVAL=LOC(1-8) 01000000
	COMMENTS="This jumper is located above and to the left of the gold
plated edge connector. It is used to select the number of wait states
required by the host computer. Position 1 inserts zero wait states, position
2 selects one wait state, and so on. If you are using an 8 Mhz backplane it
is suggested that you set the jumper to position 2 for one wait state. "
	HELP="This jumper is located above and to the left of the gold
plated edge connector. It is used to select the number of wait states
required by the host computer. Position 1 inserts zero wait states, position
2 selects one wait state, and so on. If you are using an 8 Mhz backplane it
is suggested that you set the jumper to position 2 for one wait state. "

FUNCTION="IRQ Level"
	TYPE="COM,ASY"
	COMMENTS=" The ACL II can be configured to use IRQs 3,4,5,9,10,11,12,15"
	HELP=" The ACL II can be configured to use IRQs 3,4,5,9,10,11,12,15"

	CHOICE="Select IRQ Level"
            LINK
		IRQ= 3 | 4 | 5 | 9 | 10 | 11 | 12 | 15
		SHARE=NO
		INIT=SWITCH(1) LOC(1-8) 10000000 | 01000000 | 00100000 | 00010000 | 00001000 | 00000100 | 00000010 | 00000001

	CHOICE="Disable IRQ"
		DISABLE = YES
	    FREE
		INIT=SWITCH(1) LOC(1-8) 00000000

FUNCTION="Set I/O Latch Address"
	CHOICE="Dual Port Below 1M"
	    LINK
		PORT=0200h | 0300h | 0600h | 0700h
		SHARE=NO
		SIZE=BYTE
		INIT=SWITCH(2) LOC(1 2 3 4) 0010 | 1010 | 0110 | 1110

	CHOICE="Dual Port Above 1M"
	    LINK
		PORT=0200h | 0300h | 0600h | 0700h
		SHARE=NO
		SIZE=BYTE
		PORT=0204h | 0304h | 0604h | 0704h
		SHARE=NO
		SIZE=BYTE
		INIT=SWITCH(2) LOC(1 2 3 4) 0000 | 1000 | 0100 | 1100

FUNCTION="Dual Port RAM Segment Address"
	CHOICE="Select RAM Address (Below 1M)"
	    FREE
		MEMORY=64K
		ADDRESS=0A0000h-0E0000h STEP=64K
		WRITABLE=YES
		MEMTYPE=OTHER
		SHARE=NO

	CHOICE="Select RAM Address (Above 1M)"
	    FREE
		MEMORY=64K
		ADDRESS=100000h-0FF0000h STEP=64K
		WRITABLE=YES
		MEMTYPE=OTHER
		SHARE=NO