;
; Star Gate Technologies Inc. - ACL IIR (64k)
;

BOARD
	ID="SGT1901"
	NAME="ACL IIR - Serial Card w/64k RAM"
	MFR="Star Gate"
	CATEGORY="COM"
	SLOT=ISA16
	LENGTH=330
	SKIRT=NO
	READID=NO
	COMMENTS="Star Gate ACL IIR with 64k dual port RAM."
	HELP="Star Gate ACL IIR with 64k dual port RAM."

SWITCH(1)=4
	NAME="SW1"
	STYPE=DIP
	VERTICAL=NO
	REVERSE=YES
	FACTORY=LOC(1-4)0000
	COMMENTS="Positions 1 and 2 are used to set the board I/O
 latch addresses. Position 3 determines whether the board's Dual Port
will be mapped above or below the 1 Meg boundary."
	HELP="Positions 1 and 2 are used to set the board I/O
 latch addresses. Position 3 determines whether the board's Dual Port
will be mapped above or below the 1 Meg boundary."

	
SWITCH(2)=8
	NAME="SW2"
	STYPE=DIP
	VERTICAL=NO
	REVERSE=YES
	LABEL=LOC(1-8) "irq3" "irq4" "irq5" "irq9" "irq10" "irq11" "irq12" "irq15"
	FACTORY=LOC(1-8)00000000
	COMMENTS="This switch is located just above the gold plated
 edge connector.  It is used to set the board IRQ level."
	HELP="This switch is located just above the gold plated
 edge connector.  It is used to set the board IRQ level."

	
JUMPER(1)=8
	NAME="JMP2"
	JTYPE=PAIRED
	VERTICAL=NO
	REVERSE=YES
	LABEL=LOC(1-8) "1" "2" "3" "4" "5" "6" "7" "8"
	FACTORY=LOC(1-8) 10000000
	INITVAL=LOC(1-8) 01000000
	COMMENTS="This jumper is used to select the number of wait states
required by the host computer. Position 1 inserts zero wait states, position
2 selects one wait state, and so on. If you are using an 8 Mhz backplane it
is suggested that you set the jumper to position 2 for one wait state. "
	HELP="This jumper is used to select the number of wait states
required by the host computer. Position 1 inserts zero wait states, position
2 selects one wait state, and so on. If you are using an 8 Mhz backplane it
is suggested that you set the jumper to position 2 for one wait state. "

FUNCTION="IRQ Level"
	TYPE="COM,ASY"
	COMMENTS=" The ACL IIR can be configured to use IRQs 3,4,5,9,10,11,12,15"
	HELP=" The ACL IIR can be configured to use IRQs 3,4,5,9,10,11,12,15"

	CHOICE="Select IRQ Level"
            LINK
		IRQ= 3 | 4 | 5 | 9 | 10 | 11 | 12 | 15
		SHARE=NO
		INIT=SWITCH(2) LOC(1-8) 10000000 | 01000000 | 00100000 | 00010000 | 00001000 | 00000100 | 00000010 | 00000001

	CHOICE="Disable IRQ"
		DISABLE = YES
	    FREE
		INIT=SWITCH(2) LOC(1-8) 00000000

FUNCTION="Set I/O Latch Address"
	CHOICE="Dual Port Below 1M"
	    LINK
		PORT=0200h | 0300h | 0600h | 0700h
		SHARE=NO
		SIZE=BYTE
		INIT=SWITCH(1) LOC(1 2 3 4) 0010 | 1010 | 0110 | 1110

	CHOICE="Dual Port Above 1M"
	    LINK
		PORT=0200h | 0300h | 0600h | 0700h
		SHARE=NO
		SIZE=BYTE
		PORT=0204h | 0304h | 0604h | 0704h
		SHARE=NO
		SIZE=BYTE
		INIT=SWITCH(1) LOC(1 2 3 4) 0000 | 1000 | 0100 | 1100

FUNCTION="Dual Port RAM Segment Address"
	CHOICE="Select RAM Address (Below 1M)"
	    LINK
		MEMORY=64K
		ADDRESS=0A0000h-0E0000h STEP=64K
		WRITABLE=YES
		MEMTYPE=OTHER
		SHARE=NO

	CHOICE="Select RAM Address (Above 1M)"
	    LINK
		MEMORY=64K
		ADDRESS=100000h-0FF0000h STEP=64K
		WRITABLE=YES
		MEMTYPE=OTHER
		SHARE=NO