;
; Copyright Schneider & Koch & Co. Datensysteme GmbH 1991
; Revision 1.5
; 01/22/92 RAM option enabled.
;

BOARD
   ID       = "SuK1059"
   NAME     = "SK-NET G16 LAN Interface Board"
   MFR      = "Schneider & Koch GmbH"
   CATEGORY = "NET"
   SLOT     = ISA16
   LENGTH   = 190
   COMMENTS = "SK-NET G16 Board:\n
                        product-number 11-11-059"

JUMPER(1) = 8
   NAME     = "W2"
   JTYPE    = PAIRED
   REVERSE  = YES
   FACTORY  = LOC(1-8) 10101010
   COMMENTS = "
 This jumper array selects the 8 bit or the 16 bit mode according to the bus."

SWITCH(1) = 8
   NAME     = "W1"
   STYPE    = DIP
   LABEL    = LOC(1-8) "INT0" "XTEP" "EP0" "EP1" "EP2" "IO0" "IO1" "IO2"
   REVERSE  = YES
   FACTORY  = LOC(1-8) 01000000
   COMMENTS = "
 INT0       will enable/disable IRQ3. Using IQR3 will disable COM 2\n
 XTEP       will enable (off) / disable (on) boot-ROM\n
 EP0-EP2    start address boot-ROM\n
 IO0-IO2    I/O address for POS (programable option selection)"


JUMPER(2) = 2
   NAME     = "BNC/DIX"
   JTYPE    = INLINE
   VERTICAL = YES
   LABEL    = LOC(3^2 2^1) "BNC" "DIX"
   FACTORY  = LOC(3^2 2^1) 10
   COMMENTS = "
 The position of a chip determines which transceiver and connector are used
 to connect to the network.  The default BNC position selects the internal
 transceiver and the BNC cable connector.  The DIX position selects
 the external transceiver and the DIX cable connector."


SOFTWARE(1) = "
 The current settings of your SK-G16 NET Network Interface Card are:\n"

FUNCTION = "EtherNet Adapter"
   TYPE = "NET"
   CONNECTION  = "One BNC connector and one DIX connector."

   SUBFUNCTION = "8/16 bit mode"
      HELP = "
              The 8 bit mode has to be used only for XT."
      CHOICE = "16 bit mode"
         FREE
            INIT = JUMPER(1) LOC(1-8) 10101010
            INIT = SOFTWARE(1) "16 Bit Mode"
      CHOICE = "8 bit mode"
         FREE
            INIT = JUMPER(1) LOC(1-8) 01010101
            INIT = SOFTWARE(1) "8 Bit Mode"

   SUBFUNCTION = "IRQ 3 enable/disable"
      CHOICE = "IRQ 3 disable"
         FREE
            INIT = SWITCH(1) LOC(1) 0
            INIT = SOFTWARE(1) "IRQ 3 disable"
      CHOICE = "IRQ 3 enable"
         FREE
            INIT = SWITCH(1) LOC(1) 1
            INIT = SOFTWARE(1) "IRQ 3 enabled"

   SUBFUNCTION = "IRQ Line"
      CHOICE = "IRQ 5"
         FREE
            IRQ = 5
            INIT = SOFTWARE(1) "IRQ 5"
      CHOICE = "IRQ 3"
         FREE
            IRQ = 3
            INIT = SOFTWARE(1) "IRQ 3"
      CHOICE = "IRQ 10"
         FREE
            IRQ = 10
            INIT = SOFTWARE(1) "IRQ 10"
      CHOICE = "IRQ 11"
         FREE
            IRQ = 11
            INIT = SOFTWARE(1) "IRQ 11"


   SUBFUNCTION = "Boot-PROM Start Address"
      CHOICE = "disable"
         DISABLE = YES
         FREE
            INIT = SWITCH(1) LOC(2-5) 1000
            INIT = SOFTWARE(1) "Boot PROM Disable"
      CHOICE = "DC000"
         LINK
            MEMORY  = 16K
            ADDRESS = 0DC000h
            INIT = SWITCH(1) LOC(2-5) 0000
            INIT = SOFTWARE(1) "Boot PROM DC00h"
      CHOICE = "D8000"
         LINK
            MEMORY  = 16K
            ADDRESS = 0D8000h
            INIT = SWITCH(1) LOC(2-5) 0100
            INIT = SOFTWARE(1) "Boot PROM D800h"
      CHOICE = "D4000"
         LINK
            MEMORY  = 16K
            ADDRESS = 0D4000h
            INIT = SWITCH(1) LOC(2-5) 0010
            INIT = SOFTWARE(1) "Boot PROM D400h"
      CHOICE = "D0000"
         LINK
            MEMORY  = 16K
            ADDRESS = 0D0000h
            INIT = SWITCH(1) LOC(2-5) 0110
            INIT = SOFTWARE(1) "Boot PROM D000h"
      CHOICE = "CC000"
         LINK
            MEMORY  = 16K
            ADDRESS = 0CC000h
            INIT = SWITCH(1) LOC(2-5) 0001
            INIT = SOFTWARE(1) "Boot PROM CC00h"
      CHOICE = "C8000"
         LINK
            MEMORY  = 16K
            ADDRESS = 0C8000h
            INIT = SWITCH(1) LOC(2-5) 0101
            INIT = SOFTWARE(1) "Boot PROM C800h"
      CHOICE = "C4000"
         LINK
            MEMORY  = 16K
            ADDRESS = 0C4000h
            INIT = SWITCH(1) LOC(2-5) 0011
            INIT = SOFTWARE(1) "Boot PROM C400h"
      CHOICE = "C0000"
         LINK
            MEMORY  = 16K
            ADDRESS = 0C0000h
            INIT = SWITCH(1) LOC(2-5) 0111
            INIT = SOFTWARE(1) "Boot PROM C000h"


   SUBFUNCTION = "RAM Base Address"
      CHOICE = "CC000"
         LINK
            MEMORY  = 16K
            ADDRESS = 0CC000h
            INIT = SOFTWARE(1) "RAM Base Address CC00h"
      CHOICE = "C4000"
         LINK
            MEMORY  = 16K
            ADDRESS = 0C4000h
            INIT = SOFTWARE(1) "RAM Base Address C400h"
      CHOICE = "C0000"
         LINK
            MEMORY  = 16K
            ADDRESS = 0C0000h
            INIT = SOFTWARE(1) "RAM Base Address C000h"
      CHOICE = "D0000"
         LINK
            MEMORY  = 16K
            ADDRESS = 0D0000h
            INIT = SOFTWARE(1) "RAM Base Address D000h"
      CHOICE = "D4000"
         LINK
            MEMORY  = 16K
            ADDRESS = 0D4000h
            INIT = SOFTWARE(1) "RAM Base Address D400h"
      CHOICE = "DC000"
         LINK
            MEMORY  = 16K
            ADDRESS = 0DC000h
            INIT = SOFTWARE(1) "RAM Base Address DC00h"


   SUBFUNCTION = "I/O Address for POS"
      CHOICE = "390h"
         LINK
            INIT = SWITCH(1) LOC(6-8) 000
            INIT = SOFTWARE(1) "I/O Base = 390h"
      CHOICE = "328h"
         LINK
            INIT = SWITCH(1) LOC(6-8) 100
            INIT = SOFTWARE(1) "I/O Base = 328h"
      CHOICE = "288h"
         LINK
            INIT = SWITCH(1) LOC(6-8) 010
            INIT = SOFTWARE(1) "I/O Base = 288h"
      CHOICE = "220h"
         LINK
            INIT = SWITCH(1) LOC(6-8) 110
            INIT = SOFTWARE(1) "I/O Base = 220h"
      CHOICE = "320h"
         LINK
            INIT = SWITCH(1) LOC(6-8) 001
            INIT = SOFTWARE(1) "I/O Base = 320h"
      CHOICE = "208h"
         LINK
            INIT = SWITCH(1) LOC(6-8) 101
            INIT = SOFTWARE(1) "I/O Base = 208h"
      CHOICE = "180h"
         LINK
            INIT = SWITCH(1) LOC(6-8) 011
            INIT = SOFTWARE(1) "I/O Base = 180h"
      CHOICE = "100h"
         LINK
            INIT = SWITCH(1) LOC(6-8) 111
            INIT = SOFTWARE(1) "I/O Base = 100h"


   SUBFUNCTION = "Transceiver"
      HELP = "
 Select Internal (BNC connector) if you are using
 Cheapernet. Select External (DIX connector) if
 you are using an AUI cable."
      CHOICE = "Internal (BNC connector)"
         FREE
            INIT = JUMPER(2) LOC(3^2 2^1) 10
            INIT = SOFTWARE(1) "BNC Connected"
      CHOICE = "External (DIX connector)"
         FREE
            INIT = JUMPER(2) LOC(3^2 2^1) 01
            INIT = SOFTWARE(1) "DIX Connected"