; Copyright (c) TCC 1991.  All rights reserved.
; No part may be reproduced, transmitted, transcribed, stored in retrieval
; system, or translated into any language or computer language, in any form
; or by any means, electronic, mechanical, magnetic, optical, manual,
; or otherwise, without prior written permission of TCC.
;
; Configuration file for the 53C400 SCSI Host Adapter
; @[#]TCC0120      1.20                            91/10/22

;=== Maintenance History =====================================================
;
;Rev   Date     Name Comment
;----  --------  --  ----------------------------------------------
;1.20  22.10.91  DM  Removed non-English help instructions
;1.10  30.09.91  TF  Text edits for release.
;1.00  12.04.91  DM  Initial release

BOARD
  ID = "TCC0120"
  NAME = "53C400 SCSI Host Adapter"
  MFR = "TCC"
  CATEGORY = "MSD"
  SLOT = ISA16
  LENGTH = 160
  SKIRT = NO
  READID = NO

JUMPER (1) = 11
  NAME = "JP4"
  JTYPE = PAIRED
  VERTICAL = NO
  LABEL = LOC(11-1) "ROM SIZE" "TERMPWR" "S0" "S1" "S2" "0WS" "IRQ 14" "IRQ 12"
"IRQ 11" "IRQ 10" "IRQ 5"
  FACTORY = LOC(11-1) 00100000000
  INITVAL = LOC(11-1) 0xxxx0xxxxx

JUMPER (2) = 8
  NAME = "JP1"
  JTYPE = PAIRED
  VERTICAL = NO
  LABEL = LOC(8-1) "S3" "S4" "S5" "IRQ 14" "IRQ 12" "IRQ 11" "IRQ 10" "IRQ 5"
  FACTORY = LOC(8-1) 00000000
  INITVAL = LOC(8-1) x00xxxxx

  SOFTWARE(1) = "The Novell NetWare 2.X VADD requires the IRQ level and SCSI
                 BIOS address for which your board has been configured.  The
                 options for configuring the the VADD are"

  SOFTWARE(2) = "The Novell NetWare 3.X NLM requires the IRQ level and SCSI
                 BIOS address for which your board has been configured.  The
                 command line options for loading the NLM are"

FUNCTION = "Board Configuration"
  CONNECTION = "The SCSI BUS has two connectors.  The first connector is
                labelled JP3 and intended for SCSI devices inside the system
                unit.  Connector JP3 is located to the rear of the board and
                is an unshrouded 50-pin dual inline header designed for an
                unshielded ribbon cable.  Note that pin 1 is located to the
                front of the system unit.\n\nFor SCSI devices outside of the
                system unit, connector JP2 is used.  Connector JP2 is located
                on the rear bracket and is a 50-pin Centronics type connector
                designed for a shielded cable."

  SUBFUNCTION = "IRQ Selection"
    COMMENTS = "The IRQ level selection is required for operating systems
                that depend upon an external driver for SCSI operation such
                as Novell NetWare.  Under normal circumstances an IRQ level
                is not necessary.\n\nIf an IRQ level is required, be sure to
                check the Resource and Jumper screens for further
                information."

    CHOICE = "Not Enabled"
      FREE
        INIT = JUMPER(1) LOC(5-1) 00000
        INIT = JUMPER(2) LOC(5-1) 00000
    CHOICE = "Automatic"
      LINK
        IRQ = 12 | 14 | 11 | 10 | 5
          SHARE = NO
          TRIGGER = EDGE
          INIT = JUMPER(1) LOC(5-1) 01000 | 10000 | 00100 | 00010 | 00001
          INIT = JUMPER(2) LOC(5-1) 01000 | 10000 | 00100 | 00010 | 00001
          INIT = SOFTWARE(1) "\tIRQ=12" | "\tIRQ=14" | "\tIRQ=11" |
                             "\tIRQ=10" | "\tIRQ=5"
          INIT = SOFTWARE(2) "\tINT=C" | "\tINT=E" | "\tINT=B" |
                             "\tINT=A" | "\tINT=5"

  SUBFUNCTION = "SCSI BIOS"
    COMMENTS = "The SCSI BIOS address is selected automatically by the
                configuration program."

      CHOICE = "Enabled"
        COMBINE
          MEMORY = 16K
            ADDRESS = 0DC000h | 0C8000h | 0CC000h | 0D0000h | 0D4000h | 0D8000h
            WRITABLE = YES
            MEMTYPE = SYS
            CACHE = YES
            SHARE = NO
            INIT = JUMPER(1) LOC(9-7)  100 | 001 | 101 | 011 | 111 | 000
            INIT = SOFTWARE(1) "\tMEMORY=DC000h" | "\tMEMORY=C8000h" |
                               "\tMEMORY=CC000h" | "\tMEMORY=D0000h" |
                               "\tMEMORY=D4000h" | "\tMEMORY=D8000h"
            INIT = SOFTWARE(2) "\tMEM=DC000h" | "\tMEM=C8000h" |
                               "\tMEM=CC000h" | "\tMEM=D0000h" |
                               "\tMEM=D4000h" | "\tMEM=D8000h"

FUNCTION = "SCSI BUS Configuration"
   SUBFUNCTION = "SCSI Terminator Power"
     COMMENTS = "Some external SCSI devices may require terminator power to
                 be supplied by the host adapter.  If this selection is
                 enabled, you must configure the last device on the SCSI BUS
                 to take terminator power from the BUS.  You must also change
                 the position of the TERMPWR jumper.  Refer to the Jumper
                 configuration screen for further information."

     CHOICE = "Disabled"
       FREE
         INIT = JUMPER(1) LOC(10) 0
     CHOICE = "Enabled"
       FREE
         INIT = JUMPER(1) LOC(10) 1

   SUBFUNCTION = "SCSI BUS Reset Time"
     COMMENTS = "The SCSI BUS reset time is configurable to allow for devices
                 with long power-on-self-test times.  Some very large disk
                 drives and optical devices will require the 25 second
                 delay.  You must also change the position of the S3
                 jumper.  Refer to the Jumper configuration screen for
                 further information."

     CHOICE = "5 Seconds"
       FREE
         INIT = JUMPER(2) LOC(8) 0
     CHOICE = "25 Seconds"
       FREE
         INIT = JUMPER(2) LOC(8) 1