; Copyright (c) TCC 1991.  All rights reserved. 
; No part may be reproduced, transmitted, transcribed, stored in retrieval
; system, or translated into any language or computer language, in any form
; or by any means, electronic, mechanical, magnetic, optical, manual,
; or otherwise, without prior written permission of TCC.
;
; Configuration file for the VGA-16 Video Graphics Adapter
; @[#]TCC0225      1.20                            91/10/22

;=== Maintenance History =====================================================
;
;Rev   Date     Name Comment
;----  --------  --  ----------------------------------------------
;1.20  22.10.91  DM  Removed non-English help instructions
;1.10  30.09.91  TF  Text edits for release.
;1.00  06.02.91  DM  Initial release
;
BOARD
  ID = "TCC0225"
  NAME = "VGA-16 Video Graphics Adapter"
  MFR = "TCC"
  CATEGORY = "VID"
  SLOT = ISA8OR16
  LENGTH = 163

  JUMPER(1) = 8
    JTYPE = TRIPOLE
    NAME = "Video Options"
    REVERSE = YES
    LABEL = LOC(8-1) "JP10" "JP9" "JP7" "JP6" "JP4" "JP3" "JP2" "JP1" 
    FACTORY = LOC(8-1) nn111111
    INITVAL = LOC(8-1) nnxxx11x

  JUMPER(2) = 1
    JTYPE = TRIPOLE
    NAME = "JP8"
    VERTICAL = YES
    LABEL = LOC(1) "ROM Access"
    FACTORY = LOC(1) 1

  FUNCTION = "TCC VGA-16 Configuration"
    TYPE = "VID"
    SUBFUNCTION = "VGA Mode Switching"
      COMMENTS = "Allowing all video modes lets software written for
      either color or monochrome modes to be displayed without
      restriction.\n\nRestriction of video modes to the current
      monitor type is used for operation of two monitors and two video
      boards.  It does not permit software written for monochrome modes
      to be displayed on color monitors, or software written for color
      modes to be displayed on monochrome monitors.  Use the 1C.EXE
      utility to select and switch between modes."

      CHOICE = "Allow all video modes"
        FREE
          PORT = 03B0h-03BBh
          PORT = 03D0h-03DFh
          MEMORY = 128K
            ADDRESS = 0A0000h
            MEMTYPE = OTH
          INIT = JUMPER(1) LOC(5) 1

      CHOICE = "Restrict to color modes only"
        FREE
          PORT = 03D0h-03DFh
          MEMORY = 128K
            ADDRESS = 0A0000h
            MEMTYPE = OTH
          INIT = JUMPER(1) LOC(5) 0

      CHOICE = "Restrict to monochrome modes only"
        FREE
          PORT = 03B0h-03BBh
          MEMORY = 96K
            ADDRESS = 0A0000h
            MEMTYPE = OTH
          INIT = JUMPER(1) LOC(5) 0

    SUBFUNCTION = "VGA BIOS"
      CHOICE = "Enabled in 16-bit mode"
        FREE
          MEMORY = 32K
            ADDRESS = 0C0000h
            WRITABLE = NO
            MEMTYPE = SYS
            SIZE = WORD
            DECODE = 24
            CACHE = YES
            SHARE = NO
          INIT = JUMPER(1) LOC(6) 1
          INIT = JUMPER(2) LOC(1) 1
          INIT = JUMPER(1) LOC(1) 1
      CHOICE = "Enabled in 8-bit mode"
        FREE
          MEMORY = 32K
            ADDRESS = 0C0000h
            WRITABLE = NO
            MEMTYPE = SYS
            SIZE = BYTE
            CACHE = YES
            SHARE = NO
          INIT = JUMPER(1) LOC(6) 0
          INIT = JUMPER(2) LOC(1) 0
          INIT = JUMPER(1) LOC(1) 1
      CHOICE = "Disabled"
        DISABLE = YES
        FREE
          INIT = JUMPER(1) LOC(6) 1
          INIT = JUMPER(2) LOC(1) 1
          INIT = JUMPER(1) LOC(1) 0

    SUBFUNCTION = "Monitor Type"
      CONNECTION = "The analog VGA monitor must be connected to the
      15-pin DSUB connector, labelled J1, on the rear bracket.  If a
      VGA pass-through connection is required for an ultrahigh
      resolution graphics adapter, connector P3 on the top of the board
      will be used.  A pass-through cable must be supplied by the 
      manufacturere of the other board."

      COMMENTS = "Selection of Standard VGA and PS/2 sets the board for
      standard VGA and PS/2 timing.  Use this setting for
      fixed- frequency analog monitors, PS/2 monitors, and the newer
      multi- frequency monitors.  This includes the NEC MyltiSync 2A,
      IBM 8503, 8512, 8513, and 8514.\n\nSelection of Special Multisync
      sets board to use special timing required by older
      multi-frequency monitors and some brands of 19\" and 20\"
      multi-frequency monitors.\n\nMost newer multi-frequency will work
      better using the PS/2 monitor timing."

      CHOICE = "Standard VGA and PS/2"
        FREE 
          INIT = JUMPER(1) LOC(4) 1

      CHOICE = "Special Multisync"
        FREE
          INIT = JUMPER(1) LOC(4) 0