;---------------------------------------------------------------------------;
; UNISYS Corporation           Trident 1 MB VGA Color Card                  ;
;---------------------------------------------------------------------------;
BOARD          
	ID="UNBFFD0"
	NAME="Trident 1 MB VGA Color Card       R1.04  4/27/93"
	MFR="Trident Micro Systems"
	CATEGORY="VID"
	VERSION=1.20
	SLOT=ISA8OR16
	READID=NO
	COMMENTS="Trident 1 MB VGA Color Card (p/n 12-TRID-VGA1M)
Configuration File."
	HELP="If you are unable to configure your Trident 1 MB VGA Color Card
with this configuration file please contact your Unisys Service
Representitive."

JUMPER(1)=1 NAME="J1 IRQ9 Control" JTYPE=TRIPOLE VERTICAL=YES REVERSE=YES
	LABEL=LOC(1) "J1"
	FACTORY=LOC(1) 1
	COMMENTS="Jumper J1 controls the use of IRQ9 for the vertical retrace
interrupt.  The default position of this jumper is set to cover pins 2 and 3
(rightmost position), which disables the vertical retrace interrupt.  This
allows LAN network cards to run in your system without an interrupt conflict.
If you encounter software that requires the use of the vertical retrace
interrupt, move Jumper J1 to cover pins 1 and 2 (leftmost position), which
enables the VGA controller's vertical retrace interrupt on IRQ 9."

JUMPER(2)=1 NAME="J5 Fast I/O Decode" JTYPE=TRIPOLE VERTICAL=NO REVERSE=NO
	LABEL=LOC(1) "J5"
	FACTORY=LOC(1) 1
	COMMENTS="Jumper J5 is for system boards that support fast I/O decode.
The default position of this jumper is set to cover pins 2 and 3 (topmost
position), which selects standard speed I/O decode.  If your system board
supports fast I/O decode, move the jumper to cover pins 1 and 2 (bottommost
position), which selects fast I/O decode."

JUMPER(3)=1 NAME="J6 Monitor Detection" JTYPE=TRIPOLE VERTICAL=YES REVERSE=YES
	LABEL=LOC(1) "J6"
	FACTORY=LOC(1) 0
	COMMENTS="Jumper J6 is for monitors that do not adhere to the IBM
monitor pinout standard (i.e., Samsung or Goldstar).  The default position of
this jumper is set to cover pins 1 and 2 (leftmost position), which specifies
that the monitor adheres to IBM monitor pinout standard.  If your color VGA
monitor boots up in monochrome mode, remove the jumper completely, which
specifies that a color monitor is attached.  If your monochrome VGA monitor
does not display correctly, move the jumper to cover pins 2 and 3 (rigthmost
position), which specifies that a monochrome monitor is attached."

JUMPER(4)=1 NAME="SW3 Select Scan Rate" JTYPE=PAIRED VERTICAL=YES REVERSE=YES
	LABEL=LOC(1) "SW3"
	FACTORY=LOC(1) 1
	COMMENTS="Jumper SW3 allows you to configure the scan rates of
extended VGA modes to be compatible with your multi-scanning monitor.  SW3 is
operational for 4 DRAM (512 KB) and 8 DRAM (1 MB) configurations only.  If
your monitor can scan at 48.7 KHz, remove this jumper completely."
	COMMENTS="Removing this jumper enables the following VGA Color Card
display modes:\n
\t1024x768 60 Hz non-interlaced\n
\t800x600  72 Hz non-interlaced\n
If your monitor cannot scan at 48.7 KHz, leave this jumper installed.
Installing this jumper enables the following VGA Color Card display modes:\n
\t1024x768 43 Hz interlaced\n
\t800x600  56 Hz non-interlaced"
	COMMENTS="NOTE:  Be sure to check your multi-scanning monitor's
specifications before selecting the scan rate.  Selecting a scan rate higher
than the monitor can handle may dmaage the monitor."

JUMPER(5)=1 NAME="SW4 Disable Auto16" JTYPE=PAIRED VERTICAL=YES REVERSE=YES
	LABEL=LOC(1) "SW4"
	FACTORY=LOC(1) 1
	COMMENTS="Jumper SW4 allows you to enable/disable the BIOS Autodetect
feature.  The Autodetect feature controls the BIOS interface (8- or 16-bit).
When enabled (default), the BIOS will sense whether the Impact III Graphics
Adapter is in an 8-bit or a 16-bit slot and will configure the BIOS interface
accordingly.  When disabled, the board will boot up in its default BIOS
interface setting (generally, 8-bit).\n
NOTE:  If you have problems booting your system, set Jumper SW4 to disable
Autodetect, or place the card in an 8-bit slot."

SOFTWARE(1)="When you have exited from this utility, please install drivers
and utilities for the VGA Color Card by inserting the Driver & Utilities
Diskette #1, which is supplied with this card, into drive A:, changing the
current drive to drive A: and typing \"README\""

FUNCTION="Display Controller " TYPE="VID" SHOW=NO
CHOICE="\ Enable"
	free MEMORY=128K ADDRESS=0A0000h MEMTYPE=OTH
	free MEMORY=32K ADDRESS=0C0000h MEMTYPE=OTH WRITABLE=NO CACHE=YES
	free PORT=3B4h-3B5h
	PORT=3B9h-3BBh
	PORT=3BFh
	PORT=3C0h-3CAh
	PORT=3CCh
	PORT=3CEh-3CFh
	PORT=3D4h-3D5h
	PORT=3D9h-3DCh

FUNCTION="Vertical Retrace Interrupt "
HELP="Jumper J1 controls the use of IRQ9 for the vertical retrace
interrupt.  The default position of this jumper is set to cover pins 2 and 3
(rightmost position), which disables the vertical retrace interrupt.  This
allows LAN network cards to run in your system without an interrupt conflict.
If you encounter software that requires the use of the vertical retrace
interrupt, move Jumper J1 to cover pins 1 and 2 (leftmost position), which
enables the VGA controller's vertical retrace interrupt on IRQ 9."
CHOICE="\ Disable"
	free INIT=JUMPER(1) LOC(1) 1
CHOICE="\ Enable, IRQ 9\ "
	free IRQ=9
	INIT=JUMPER(1) LOC(1) 0

FUNCTION="Monitor Detection Control "
	COMMENTS="Jumper J6 is for monitors that do not adhere to the IBM
monitor pinout standard (i.e., Samsung or Goldstar).  The default position of
this jumper is set to cover pins 1 and 2 (leftmost position), which specifies
that the monitor adheres to IBM monitor pinout standard.  If your color VGA
monitor boots up in monochrome mode, remove the jumper completely, which
specifies that a color monitor is attached.  If your monochrome VGA monitor
does not display correctly, move the jumper to cover pins 2 and 3 (rigthmost
position), which specifies that a monochrome monitor is attached."
CHOICE="\ IBM Compatible Monitor"
	free INIT=JUMPER(3) LOC(1) 0
CHOICE="\ Incompatible Color Monitor"
	free INIT=JUMPER(3) LOC(1) n
CHOICE="\ Incompatible Monochrome Monitor\ "
	free INIT=JUMPER(3) LOC(1) 1

FUNCTION="I/O Decode Speed Control " SHOW=EXP
HELP="Jumper J5 is for system boards that support fast I/O decode.
The default position of this jumper is set to cover pins 2 and 3 (topmost
position), which selects standard speed I/O decode.  If your system board
supports fast I/O decode, move the jumper to cover pins 1 and 2 (bottommost
position), which selects fast I/O decode."
CHOICE="\ Standard I/O decode\ "
	free INIT=JUMPER(2) LOC(1) 1
CHOICE="\ Fast I/O Decode"
	free INIT=JUMPER(2) LOC(1) 0

FUNCTION="Monitor Scan Rate "
HELP="Jumper SW3 allows you to configure the scan rates of
extended VGA modes to be compatible with your multi-scanning monitor.  SW3 is
operational for 4 DRAM (512 KB) and 8 DRAM (1 MB) configurations only.  If
your monitor can scan at 48.7 KHz, remove this jumper completely."
HELP="Removing this jumper enables the following VGA Color Card
display modes:\n
\t1024x768 60 Hz non-interlaced\n
\t800x600  72 Hz non-interlaced\n
If your monitor cannot scan at 48.7 KHz, leave this jumper installed.
Installing this jumper enables the following VGA Color Card display modes:\n
\t1024x768 43 Hz interlaced\n
\t800x600  56 Hz non-interlaced"
HELP="NOTE:  Be sure to check your multi-scanning monitor's
specifications before selecting the scan rate.  Selecting a scan rate higher
than the monitor can handle may dmaage the monitor."
CHOICE="\ Greater than 48 KHz\ "
	free INIT=JUMPER(4) LOC(1) 0
CHOICE="\ Less than 48 KHz"
	free INIT=JUMPER(4) LOC(1) 1

FUNCTION="BIOS Autodetect Control "
HELP="Jumper SW4 allows you to enable/disable the BIOS Autodetect
feature.  The Autodetect feature controls the BIOS interface (8- or 16-bit).
When enabled (default), the BIOS will sense whether the Impact III Graphics
Adapter is in an 8-bit or a 16-bit slot and will configure the BIOS interface
accordingly.  When disabled, the board will boot up in its default BIOS
interface setting (generally, 8-bit).\n
NOTE:  If you have problems booting your system, set Jumper SW4 to disable
Autodetect, or place the card in an 8-bit slot."
CHOICE="\ Disable"
	free INIT=JUMPER(5) LOC(1) 1
CHOICE="\ Enable"
	free INIT=JUMPER(5) LOC(1) 0