;************************************************************************
;
;       UltraStor ISA SCSI Host Adapter (ULTRA 14FB)
;
;	UltraStor ULTRA 14FB EISA configuration file
;	Version: 1.00
;	Date   : May 11, 1993
;
;************************************************************************

;------------------------------------------------------------------------
;	Board Identification Block
;------------------------------------------------------------------------

BOARD
  ID = "USC0142"
  NAME = "UltraStor - ULTRA 14FB ISA SCSI Host Adapter" 
  MFR = "UltraStor"
  CATEGORY = "MSD"			;Mass Storage Device
  SLOT = ISA16				;For ISA-16 bit slot
  LENGTH = 210
  AMPERAGE = 800
  SKIRT = NO
  READID = NO

  COMMENTS = "ULTRA 14FB is a high performance ISA SCSI host adapter
	supporting up to 7 SCSI devices. A high speed 8 bit micro-processor
	provides the local intelligence for command processing.\n\n
	The ULTRA 14FB features:\n
	. ISA BUS master burst transfer rate of up to 10MB/sec.\n
	. MailBox Command/Status Protocol for Multi-Threaded
	  Command Chaining and Queuing, and Scatter/Gather.\n
	. Coexits with other disk controllers / H/A in a system.\n
	. Easy controller configuration using software utility.\n
	. Device specific setup options.\n\n"

;------------------------------------------------------------------------
;	Initialization Information Block
;------------------------------------------------------------------------

;**************  Jumper Configuration Statement Block  ******************

JUMPER(2) = 1
	NAME = "JP2"
	JTYPE = PAIRED
	VERTICAL = YES
	REVERSE = YES
	INITVAL = LOC(1) x
	FACTORY = LOC(1) 1
	LABEL = LOC(1) "FLOPPY"
	COMMENTS = "\tFloppy Controller:\n\n
		    \tEnable  : Jumper in\n
		    \tDisable : Jumper out\n"

JUMPER(11) = 3
	NAME = "JP11"
	JTYPE = PAIRED
	VERTICAL = NO
	REVERSE = YES
	INITVAL = LOC(1-3) xxx
	FACTORY = LOC(1-3) 010
	LABEL = LOC(1-3) "BIOS ADDR1" "BIOS ADDR2" "BIOS ADDR3"
	COMMENTS =
		"\tBIOS Address Setting:\n
		 \tAddress     1-2   3-4   5-6\n
		 \tDisable     OUT   OUT   OUT\n
		 \tC4000       OUT   OUT   IN\n
		 \tC8000       OUT   IN    OUT\n
		 \tCC000       OUT   IN    IN\n
		 \tD0000       IN    OUT   OUT\n
		 \tD4000       IN    OUT   IN\n
		 \tD8000       IN    IN    OUT\n
		 \tDC000       IN    IN    IN\n"

JUMPER(12) = 4
	NAME = "JP12"
	JTYPE = PAIRED
	VERTICAL = NO
	REVERSE = YES
	LABEL = LOC(1-4) "I/O ADDR1" "I/O ADDR2" "I/O ADDR3" "ConfigCtrl"
	INITVAL = LOC(1-4) xxxx
	FACTORY = LOC(1-4) 0000
	COMMENTS =
		"\tMailBox Port I/O Address:\n
		 \t Address    1-2   3-4   5-6\n
		 \t  330H      OUT   OUT   OUT\n
		 \t  340H      OUT   OUT   IN\n
		 \t  310H      OUT   IN    OUT\n
		 \t  230H      OUT   IN    IN\n
		 \t  240H      IN    OUT   OUT\n
		 \t  210H      IN    OUT   IN\n
		 \t  130H      IN    IN    OUT\n
		 \t  140H      IN    IN    IN\n\n

		 \tConfiguration Control:\n
		 \t OUT : BIOS and I/O addresses are controlled by software\n
		 \t IN  : BIOS address controller by JP11 pins 1-2 3-4 5-6\n
		 \t       I/O address controller by JP12 pins 1-2 3-4 5-6\n"

;***********************************************************************

GROUP = "UltraStor ULTRA 14FB Disk Controller"
TYPE = "MSD"

FUNCTION = "Host Adapter Options"
TYPE = "HDKCTL"

    SUBFUNCTION = "BIOS Address Selection"
    COMMENTS = "Jumper configuration is valid only with jumper JP12
		pins 7-8 jumpered.\n" 
	CHOICE = "C8000h"
        FREE
	MEMORY = 16K
	ADDRESS = 0C8000h
	MEMTYPE = OTH
	WRITABLE = YES
	SHARE = NO
	SIZE = BYTE
	CACHE = YES
	INIT = JUMPER(11) LOC(1 2 3) 010

	CHOICE = "C4000h"
        FREE
	MEMORY = 16K
	ADDRESS = 0C4000h
	MEMTYPE = OTH
	WRITABLE = YES
	SHARE = NO
	SIZE = BYTE
	CACHE = YES
	INIT = JUMPER(11) LOC(1 2 3) 001

	CHOICE = "CC000h"
        FREE
	MEMORY = 16K
	ADDRESS = 0CC000h
	MEMTYPE = OTH
	WRITABLE = YES
	SHARE = NO
	SIZE = BYTE
	CACHE = YES
	INIT = JUMPER(11) LOC(1 2 3) 011

	CHOICE = "D0000h"
        FREE
	MEMORY = 16K
	ADDRESS = 0D0000h
	MEMTYPE = OTH
	WRITABLE = YES
	SHARE = NO
	SIZE = BYTE
	CACHE = YES
	INIT = JUMPER(11) LOC(1 2 3) 100

	CHOICE = "D4000h"
        FREE
	MEMORY = 16K
	ADDRESS = 0D4000h
	MEMTYPE = OTH
	WRITABLE = YES
	SHARE = NO
	SIZE = BYTE
	CACHE = YES
	INIT = JUMPER(11) LOC(1 2 3) 101

	CHOICE = "D8000h"
        FREE
	MEMORY = 16K
	ADDRESS = 0D8000h
	MEMTYPE = OTH
	WRITABLE = YES
	SHARE = NO
	SIZE = BYTE
	CACHE = YES
	INIT = JUMPER(11) LOC(1 2 3) 110

	CHOICE = "DC000h"
        FREE
	MEMORY = 16K
	ADDRESS = 0DC000h
	MEMTYPE = OTH
	WRITABLE = YES
	SHARE = NO
	SIZE = BYTE
	CACHE = YES
	INIT = JUMPER(11) LOC(1 2 3) 111

        CHOICE = "Disable" 
	FREE
	INIT = JUMPER(11) LOC (1 2 3) 000

    SUBFUNCTION = "I/O Port Address Selection"
    COMMENTS = "Jumper configuration is valid only with jumper JP12
		pins 7-8 jumpered.\n" 
	CHOICE = "330H"
	LINK
	PORT = 330h-33Fh
	INIT = JUMPER(12) LOC(1 2 3) 000

	CHOICE = "340H"
	LINK
	PORT = 340h-34Fh
	INIT = JUMPER(12) LOC(1 2 3) 001

	CHOICE = "310H"
	LINK
	PORT = 310h-31Fh
	INIT = JUMPER(12) LOC(1 2 3) 010

	CHOICE = "230H"
	LINK
	PORT = 230h-23Fh
	INIT = JUMPER(12) LOC(1 2 3) 011

	CHOICE = "240H"
	LINK
	PORT = 240h-24Fh
	INIT = JUMPER(12) LOC(1 2 3) 100

	CHOICE = "210H"
	LINK
	PORT = 210h-21Fh
	INIT = JUMPER(12) LOC(1 2 3) 101

	CHOICE = "130H"
	LINK
	PORT = 130h-13Fh
	INIT = JUMPER(12) LOC(1 2 3) 110

	CHOICE = "140H"
	LINK
	PORT = 140h-14Fh
	INIT = JUMPER(12) LOC(1 2 3) 111

    SUBFUNCTION = "Configuration Control Selection"
    COMMENTS = "This jumper selects board configuration to be controlled
		by jumper or software.\n" 
	CHOICE = "Software"
	FREE
	INIT = JUMPER(12) LOC(4) 0

	CHOICE = "Jumper"
	FREE
	INIT = JUMPER(12) LOC(4) 1

FUNCTION = "Floppy Disk Option"
TYPE = "FDKCTL"

    SUBFUNCTION = "Floppy Enable / Disable"
    COMMENTS = "Enable or disable floppy drive controller.\n"
	CHOICE = "Enable"
	COMBINE
	  IRQ = 6
	  SHARE = NO
	  TRIGGER = EDGE
	  PORT = 03F0h-03F7h
	  SIZE = BYTE
	  INIT = JUMPER(2) LOC(1) 1

	CHOICE = "Disable"
	FREE
	INIT = JUMPER(2) LOC(1) 0

ENDGROUP;