;Western Digital WD1007V-SE2 Winchester/Floppy Controller BOARD ID = "WDT0002" ;?Temporary ID NAME = "Western Digital WD1007V-SE2 Disk/Floppy Controller" MFR = "Western Digital" CATEGORY= "MSD" SLOT = ISA16 ; LENGTH = 171 COMMENTS= "Interfaces two ESDI-compatible hard disk drives and two floppy disk drives.\n Before installing verify proper termination of the last hard disk drive. The last drive (and only the last drive) requires a termination resistor.\n" HELP = "\n\n" ; SOFTWARE(1) = "If the WD1007V BIOS ROM is disabled, Western Digital's WDFMT program will be necessary for low-level formatting ." JUMPER(1) = 6 JTYPE =PAIRED NAME ="W1 Firmware Options" LABEL =LOC(1-6) "2-1:CACHE" "4-3:ECC" "6-5:TRNSLN" "8-7:RESVD" "10-9 :SPT" "12-11:ALT" VERTICAL =NO REVERSE =YES FACTORY =LOC(1-6) 000000 COMMENTS ="If replacing a WD1007A controller with a WD1007V install jumpers on 9-10 and 11-12 to avoid reformatting the drive(s)." JUMPER(2) = 1 JTYPE =PAIRED NAME ="BIOS Enable" VERTICAL =YES LABEL =LOC(1) "W3" INITVAL =LOC(1) 1 COMMENTS ="The Jumper enables the WD0007V BIOS ROM. If disabled, the WDFMT program will be necessary for low-level formatting." ;JUMPER(3) = 1 ; JTYPE =PAIRED ; NAME ="Floppy Controller" ; VERTICAL =YES ; LABEL =LOC(1) "W4" ; INITVAL =LOC(1) 0 ; COMMENTS ="No jumper setting enables the Floppy Controller. This ; is the standard setting." JUMPER(4) = 1 JTYPE =PAIRED NAME ="Floppy Spindle Speed" VERTICAL =YES LABEL =LOC(1) "W5" INITVAL =LOC(1) 0 COMMENTS ="No jumper setting selects Single spindle speed Floppy Drive. Setting the jumper selects Dual speed. Normally, the jumper is not set." JUMPER(5) = 2 JTYPE =PAIRED NAME ="Drive(s) Address" VERTICAL =YES REVERSE =YES LABEL =LOC(1 2) "W12""W6" FACTORY =LOC(1 2) 00 COMMENTS ="To select the module's secondary address ranges, install jumpers on W6 1-2(floppy drives) and W12 1-2 (fixed drives). The primary address ranges of 1F0- 1F7 (fixed) and 3F2-3F7(floppy) are selected when jumpers are not installed. Secondary address ranges of 170-177(fixed) and 372-377(floppy) should be selected only when using a second controller." JUMPER(6) = 1 JTYPE =TRIPOLE NAME ="IRQ" VERTICAL =YES LABEL =LOC(1) "W7:1-2-3" FACTORY =LOC(1) 0 COMMENTS ="A jumper on 1-2 selects IRQ14. This is factory installed since it is used by most operating systems, such as MS-DOS and OS/2. Some operating systems may work with IRQ15 if custom drivers are installed. The 2-3 setting specifies IRQ15." JUMPER(7) = 1 JTYPE =TRIPOLE NAME ="BIOS Address" VERTICAL =YES LABEL =LOC(1) "W8:1-2-3" FACTORY =LOC(1) 1 COMMENTS ="The 2-3 jumper selects BIOS address range CC000 - CFFFF. This is the usual setting. The 1-2 jumper setting selects Address range C8000-CBFFF." JUMPER(8) = 1 JTYPE =PAIRED NAME ="Mounting Bracket" VERTICAL =YES LABEL =LOC(1) "W9" INITVAL =LOC(1) 0 COMMENTS ="If jumper is set, the mounting bracket ground is connected to the logical ground. The usual setting is no jumper" FUNCTION = "ESDI DISK/FLOPPY CONTROLLER" TYPE ="MSD" HELP="Use E)dit Change R)esource to Select Options." CONNECTION = "Termination of last drive:\n\tVerify proper termination of the last hard disk drive. The last drive in your system requires a termination resistor.\n\nCables:\n\tJumpers may be required, based on drive selection and whether twisted or non-twisted cables are being used. See the installation manual for instructions." SUBFUNCTION = "BIOS Memory Options" CHOICE = "BIOS Address" LINK MEMORY = 8K ADDRESS = 0CC000h|0C8000h MEMTYPE = OTH INIT = JUMPER(7) LOC(1) 1|0 SUBFUNCTION = "IRQ Options" CHOICE = "IRQ Selection" LINK IRQ = 14|15 INIT = JUMPER(6) LOC(1) 0 | 1 SUBFUNCTION = "Disk Options" CHOICE = "Disk Address" LINK PORT = 1F0h-1F7h|170h-177h INIT = JUMPER(5) LOC(1) 1 | 0 SUBFUNCTION = "Floppy Options" CHOICE = "Floppy Address" LINK PORT = 3F2h - 3F7h | 372h - 377h INIT = JUMPER(5) LOC(2) 1 | 0 FREE IRQ = 6 DMA = 2