;Western Digital WD1007A-WAH Winchester Controller
BOARD
	ID	= "WDT0004"	;?Temporary ID
	NAME	= "Western Digital WD1007A-WAH Winchester Controller"
	MFR	= "Western Digital"
	CATEGORY= "MSD"
	SLOT	= ISA16		;
        LENGTH  = 171
	COMMENTS= "\nInterfaces two ESDI-compatible hard disk drives.  Before 
		  installing verify proper termination of the last hard disk 
		  drive.  The last drive (and only the last drive ) requires  
		  a termination resistor.\n"	;
	HELP	= "\n\n"	;?

JUMPER(1) = 2
	JTYPE		=TRIPOLE
	NAME		="BIOS Address"
	VERTICAL 	=YES
	REVERSE		=YES
	LABEL		=LOC(1 2) "W2:1-2-3" "W1:1-2-3"
	FACTORY		=LOC(1 2) 11
	COMMENTS	="BIOS Address Select.  The standard setting of jumpers
			 is 2-3 on both W1 and W2. This selects the address 
			 range of C8000-C9FFF.  If BIOS disabled, no jumpers
			 should be set."
JUMPER(2) = 1
	JTYPE		=PAIRED
	NAME		="BIOS Enable"
	VERTICAL	=YES
	LABEL		=LOC(1)	"W3"
	FACTORY		=LOC(1) 1
	COMMENTS	="The Jumper enables the WD0007-WA2 BIOS, which is
			  the standard setting.  If disabled, the WDFMT 
			  program will be necessary for low-level formatting."

JUMPER(7) = 1
	JTYPE		=PAIRED
	NAME		="WD1007/WD1005 Mode"
	VERTICAL	=YES
	LABEL		=LOC(1)	"W8"
	INITVAL		=LOC(1)	0
	COMMENTS	="No jumper setting selects standard WD1007 mode of 
			  operation, which is the standard setting.  A jumper 
			  setting selects the WD1005-WAH compatibility mode of 
			  operation."
JUMPER(8) = 1
	JTYPE		=PAIRED
	NAME		="Chassis Ground"
	VERTICAL	=YES
	LABEL		=LOC(1) "W9"
	INITVAL		=LOC(1) 0
	COMMENTS	="No jumper setting selects Chassis Ground 
			  disconnected, which is the standard setting.  A
			  jumper setting selects a connected status."
JUMPER(9) = 1
	JTYPE		=PAIRED
	NAME		="Digital Input Reg."
	VERTICAL	=YES
	LABEL		=LOC(1) "W10"
	INITVAL		=LOC(1) 0
	COMMENTS	="No jumper setting selects Digital Input Register 
			  Unlatched which is the standard setting."
JUMPER(10) = 1
	JTYPE		=PAIRED
	NAME		="Diskette Change"
	VERTICAL	=YES
	LABEL		=LOC(1) "W11"
	INITVAL		=LOC(1) 1
	COMMENTS	="A jumper setting selects the Diskette Change Enable 
			  with FDC Option.  This is the standard setting."
JUMPER(11) = 1
	JTYPE		=PAIRED
	NAME		="Disk Address"
	VERTICAL	=YES
  	LABEL		=LOC(1)	"W12"
	FACTORY		=LOC(1) 0
	COMMENTS	="No jumper setting selects address 1FX(1F0-1F7), which
			  is the standard setting.
			  A jumper setting  selects address 17X(170-177).
			  This should be used for a secondary fixed disk. "

JUMPER(13) = 1
	JTYPE		=PAIRED
	NAME		="Sector Translation"
	VERTICAL	=YES
	LABEL		=LOC(1) "W14"
	INITVAL		=LOC(1) 0
	COMMENTS	="No jumper setting is standard and selects Sector 
			  Translation Enabled which provides physical to 
			  logical translation so ESDI drives can be fully 
			  utilized in the PC/AT environment.  A jumper 
			  disables the translation."
JUMPER(14) = 1
	JTYPE		=PAIRED
	NAME		="ECC bytes"
	VERTICAL	=YES
	LABEL		=LOC(1) "W15"
	INITVAL		=LOC(1) 0
	COMMENTS	="No jumper setting is standard and selects 4 bytes 
			  ECC.  A jumper selects 7 bytes ECC."  

SOFTWARE(1) = "If the WD1007A BIOS ROM is disabled, Western Digital's WDFMT 
		program will be necessary for low-level formatting.\n\n"
FUNCTION	= "Fixed Disk Controller"
TYPE 		= "MSD"
HELP		= "Use E)dit Change R)esource to Select Options"
CONNECTION = "Cables:\nConnect the 34-pin control cable to J1 connector and
the hard disk drive.\nAttach a 20-pin data cable to J2 connector(for Drive 0)
and connect to proper hard disk drive.\nAttach a 20-pin data cable to J3
connector(for Drive 1) and connect to proper hard disk drive.\nAttach the
34-pin daisy-chain cable to J4 connector and connect to the floppy drive(s).\n
Attach Winchester activity LED connector to J5." 
SUBFUNCTION = "BIOS Memory Options"

CHOICE = "Enable BIOS"
LINK
	MEMORY	= 8K
	 ADDRESS=0C8000h | 0CA000h | 0CC000h | 0CE000h
	 MEMTYPE=OTH
	INIT=JUMPER(1) LOC(1 2) 11 | 01 | 10 | 00
FREE
	INIT=JUMPER(2)LOC(1) 1
CHOICE = "Disable BIOS"
FREE
	INIT=JUMPER(2)LOC(1) 0
SUBFUNCTION = "Disk Options"
CHOICE = "Disk Address Options"
LINK
	PORT = 1F0h-1F7h|170h-177h
	INIT = JUMPER(11) LOC(1) 0|1