BOARD
	ID = "NICC105"
	NAME = "National Instruments GPIB-PCIIA Interface Board"
	MFR = "NATIONAL INSTR CORP"
	CATEGORY = "COM"
	SLOT = ISA8
	READID = NO
        LENGTH = 110                                 ;11.05cm = 4.35inches
        AMPERAGE = 490 			   	     ;0.490 Amps
        SKIRT = NO
	COMMENTS = "GPIB-PCIIA EISA configuration file Version 2.0; 
                    For further information call
                    National Instruments at 1-800-433-3488."
	HELP = "Sorry, no help available."

SWITCH(1) = 9
	NAME = "Base I/O Address"
	STYPE = DIP
	VERTICAL = NO
	REVERSE = YES
	LABEL = LOC(1-9) "I0" "I1" "I2" "A14" "A13" "X" "X" "7210" "PCIIA"
	FACTORY = LOC(1-9) 000111101
	INITVAL = LOC(1-9) XXXXXXXX1                  ;set for PCIIA mode
	COMMENTS = "The base I/O address is determined by the settings of the
		    board DIP switch (U2) positions 1-7. The factory setting is 
		    for base address 2B8h.  Position 8 switches the chip emulation
                    mode between 7210 and 9914.  Leave this switch in the 7210 position
                    for normal operation with NI driver software.  Position 9 switches
                    the board emulation mode between PCII and PCIIA.  For PCII mode,
                    use the PCII configuration file, !NICC205.CFG."

JUMPER(1) = 6
	NAME = "DMA (W2)"
	JTYPE = PAIRED
	VERTICAL = NO
	REVERSE = YES
	LABEL = LOC(1-6) "DACK1" "DRQ1" "DACK2" "DRQ2" "DACK3" "DRQ3"
	FACTORY = LOC(1-6) 110000
        ;Factory defaults - DACK1,DRQ1                                                             
	COMMENTS = "The DMA channel used is determined by this jumper.
		    Note that both the DRQ (request) and DACK (acknowledge) jumpers must
		    be set to the same channel if that channel is to be used."

		    
JUMPER(2) = 6
	NAME = "IRQ Level (W3)"
	JTYPE = PAIRED
	VERTICAL = NO
	REVERSE = YES
	LABEL = LOC(1-6) "IRQ2" "IRQ3" "IRQ4" "IRQ5" "IRQ6" "IRQ7"
	FACTORY = LOC(1-6) 000001
        ;Factory default is IRQ7 
	COMMENTS = "The IRQ level (2, 3, 4, 5, 6, or 7) is determined by this
		    jumper.  The GPIB-PCIIA supports shared interrupts."


FUNCTION = "GPIB-PCIIA Interface"

  SUBFUNCTION = "Base I/O Address"
    COMMENTS = "The base I/O address is selected through this resource.
                Note that since this address uses negative
                logic, if your screen or report shows you a binary
                representation of the switch, the ones and zeroes will
                be reversed.  The 'ON' and 'OFF' settings given by the
                configuration utility are correct."
  CHOICE = "2E1"
    LINK
      PORT = 02E1h
      INIT = SWITCH(1) LOC(4-7) 1111
  CHOICE = "22E1"
    LINK
      PORT = 22E1h
      INIT = SWITCH(1) LOC(4-7) 1011
  CHOICE = "42E1"
    LINK
      PORT = 42E1h
      INIT = SWITCH(1) LOC(4-7) 0111
  CHOICE = "62E1"
    LINK
      PORT = 62E1h
      INIT = SWITCH(1) LOC(4-7) 0011

          
  SUBFUNCTION = "DMA Channel"
    CHOICE = "1"
      LINK
        DMA = 1
        INIT = JUMPER(1) LOC(1-6) 110000
    CHOICE = "2"
      LINK
        DMA = 2
        INIT = JUMPER(1) LOC(1-6) 001100
    CHOICE = "3"
      LINK
        DMA = 3
        INIT = JUMPER(1) LOC(1-6) 000011
    CHOICE = "Disabled"
      LINK
        INIT = JUMPER(1) LOC(1-6) 000000

  SUBFUNCTION = "Interrupt Request Line"
    CHOICE = "7"
      LINK
        IRQ = 7
        SHARE = YES
        INIT = JUMPER(2) LOC(1-6) 000001
        INIT = SWITCH(1) LOC(1-3) 000
    CHOICE = "2"
      LINK
        IRQ = 2
        SHARE = YES
        INIT = JUMPER(2) LOC(1-6) 100000
        INIT = SWITCH(1) LOC(1-3) 101
    CHOICE = "3"
      LINK
        IRQ = 3
        SHARE = YES
        INIT = JUMPER(2) LOC(1-6) 010000
        INIT = SWITCH(1) LOC(1-3) 001
    CHOICE = "4"
      LINK
        IRQ = 4
        SHARE = YES
        INIT = JUMPER(2) LOC(1-6) 001000
        INIT = SWITCH(1) LOC(1-3) 110
    CHOICE = "5"
      LINK
        IRQ = 5
        SHARE = YES
        INIT = JUMPER(2) LOC(1-6) 000100
        INIT = SWITCH(1) LOC(1-3) 010
    CHOICE = "6"
      LINK
        IRQ = 6
        SHARE = YES
        INIT = JUMPER(2) LOC(1-6) 000010
        INIT = SWITCH(1) LOC(1-3) 100
    CHOICE = "Disabled"
      LINK
        INIT = JUMPER(2) LOC(1-6) 000000
        INIT = SWITCH(1) LOC(1-3) 111