Subject: Solaris 2 Frequently Asked Questions (FAQ) 1.63
Date: 7 Sep 1997 15:25:45 GMT
Summary: This posting contains a list of Frequently Asked Questions (and
    answers) about Sun Microsystem's Solaris 2.x system in general.
    See also the FAQ archived as Solaris2/Porting.

Archive-name: Solaris2/FAQ
Version: 1.63
Last-Modified: 1997/09/07 15:31:33
Maintained-by: Casper Dik <Casper.Dik@Holland.Sun.COM>

The following is a list of questions that are frequently asked about
Solaris 2.x.  You can help make it an even better-quality FAQ by writing a
short contribution or update and sending it BY EMAIL ONLY to me.
Thanks!

As you may have noted, I have switched employers and work for Sun as of
April 1st 1995.  Sun is in no way responsible for the contents
of this FAQ.

The latest Solaris 2 FAQ, including an HTML version, and some other goodies
can be obtained through ftp from <ftp://ftp.wins.uva.nl/pub/solaris>.

A new version of the FAQ is available with an index separate from
all questions, it's <http://www.wins.uva.nl/pub/solaris/solaris2/>.
So it's a lot quicker to download.  Also, an experimental FAQ search service
at <http://www.wins.uva.nl/cgi-bin/sfaq.cgi> is now available.

Please note that these addresses have changed because of a reorg.  Just
replace "fwi" in the old addresses with "wins".  The old addresses will
continue to work until March 1st, 1998.

The HTML <http://www.wins.uva.nl/pub/solaris/solaris2.html> version
of the FAQ contains references to most FTP sites and files mentioned
in the FAQ.  The references to ftp sites are always to either HTML
files or directories, never to binary files.

I've added an index of questions and marked changed(*) and added
questions(+).  The FAQ is being reorganized, time permitting.
The index is generated automatically, so there may be errors there.
Not all questions are in the section they belong in. Suggestions on
how best to subdivide/order the FAQ are welcome.



 1. GENERAL
   1.1) What's Solaris anyway?
   1.2) Why should I upgrade?
   1.3) Should I move to Solaris 2.x now, or later, or never?
   1.4) What is Solaris 2? Is it really SVR4 based?
| *1.5) What machines does Solaris 2.x run on?
   1.6) Will my old applications from 4.1.x run on Solaris 2?
|  1.7) Will my SPARC binaries run unchanged on UltraSPARC machines?
   1.8) Will my old applications from SVR3 on the 386 run on Solaris 2/x86?
   1.9) Where has the XXX command gone now?
   1.10) When I upgrade, should I use SunInstall "upgrade", or start over?
   1.11) Is Solaris 2.x reliable/stable enough to use?
   1.12) Why do some people dislike Solaris2?
| *1.13) Why do some people *like* Solaris2?
   1.14) What is Sun doing to help me migrate?
|  1.15) Can I use my SunOS 4 disks on Solaris 2.x?
   1.16) How can I enable System V IPC? Ipcs says it isn't configured in.

|2. SOURCES OF INFORMATION
| *2.1) How can I RTFM when I don't have it anymore?
   2.2) Why is "man -k" so confused?
|  2.3) What Software is available for Solaris 2.x?
   2.4) What FTP/WWW sites do I need to know about?
   2.5) What other FAQ's do I need to know about?
   2.6) What mailing lists should I get?
   2.7) What books should I read?
   2.8) What hardware is supported by Solaris 2.x for Intel?
  *2.9) What is Wabi?
   2.10) I'm running into some limits of SunOS 4.x, will upgrading to
.Solaris 2.x help?

 3. SYSTEM ADMINISTRATION
   3.1) How much disk space do I need to install Solaris 2?
   3.2) How can I convert all my local changes that I've made over the
.years into their corresponding forms on Solaris 2?
   3.3) What are "packages"?
| *3.4) Why can't I write in/mount over /home?
   3.5) Why can't I access CDs or floppies?
   3.6) Why are there no passwords in /etc/passwd?
   3.7) Why can't I rlogin/telnet in as root?
   3.8) How can I have a user without a password?
|  3.9) How can I set up anonymous FTP?
   3.10) How can I print from a Solaris 2 (or any System V Release 4) system
.to a SunOS4.x (or any other BSD) system?
   3.11) Why does lp complain about invalid content types?
   3.12) My jobs stay in the queue after printing.
| *3.13) Are there any alternatives to the system V spooler?
   3.14) What happened to /dev/MAKEDEV? How do I add devices?
   3.15) Why isn't my tape/cd player or new disk/device recognized?
   3.16) What happened to /etc/rc and /etc/rc.local?
   3.17) Can't I have /etc/rc.local back?
   3.18) Why are there two versions of shutdown?
   3.19) When will somebody publish a package of the BSD (4.3BSD Net2)
."init", "getty", and "rc/rc.local", so we can go back to life
.in the good old days?
   3.20) What has happened to getty? What is pmadm and how do you use it?
   3.21) How do I get the screen to blank when nobody's using it?
   3.22) And what about screendump, screenload and clear_colormap?
   3.23) Where did etherfind go?
| *3.24) Can I run SunOS4.1.x on my SPARC Classic, LX, SS5, SS4, SS20, Voyager,
.SS1000, SC2000, CS6400, Ultra?
   3.25) The "find" program complains that my root directory doesn't exist?
   3.26) I'm having troubles with high-speed input on the Sparc serial
.ports.  What should I do?
|  3.27) How do I make ksh or csh be the login shell for root?
   3.28) What is this message: "automount: No network locking on host,
.contact administrator to install server change."?
|  3.29) I have all kinds of problems with SCSI disks under Solaris 2.x
.They worked fine under SunOS 4.x.
   3.30) How do I make Solaris2 use my old ADAPTEC ACB-4000 and
.Emulex MD-21 disk controllers?
   3.31) Should I wait installing 2.5 until there are enough patches?
   3.32) Why are there so many patches for Solaris 2.x?
   3.33) What are the ``mandatory'' patches I keep hearing about?
   3.34) Which patches should I apply?
   3.35) Where do I get patches from?
   3.36) Where can I obtain Solaris 2/x86 driver updates?
   3.37) Why does installing patches take so much space in /var/sadm?
   3.38) Do I need to back out previous versions of a patch?
   3.39) How can I have more than 48 pseudo-ttys?
   3.40) How can I have normal users chown their files?
   3.41) How can I get ps to print %MEM and %CPU?
   3.42) How can I get the DOS and Unix clock to agree on Solaris/x86?
   3.43) How can I increase the number of file descriptors per process?
   3.44) Can I install both SunOS and Solaris on the same machine,
.and choose between them at boot time?
   3.45) How do I disable banner pages under Solaris?
   3.46) How do I change my hostname?
   3.47) Can I run multiple terminals on the console of Solaris x86
.like those supported on Interactive Unix and SCO?
   3.48) How can I prevent daemons from creating mode 666 files?
   3.49) How do I change the terminal type for /dev/console?
   3.50) If I login over the network, my terminal type is set to "sun"/"AT386"
.How can I change that?  In SunOS 4.x the type would have been "network"
   3.51) How can I change the SYSV IPC parameters?
|  3.52) How do I enable/disable dtlogin?

 4. NETWORKING
   4.1) How do I use DNS w/o using NIS or NIS+?
   4.2) Speaking of nsswitch.conf, what is it?
   4.3) What does [NOTFOUND=return] in nsswitch.conf mean?
   4.4) Can I run a nis/yp server under Solaris 2.x?
   4.5) Can I run NIS+ under Solaris 1 (SunOS 4.1.x)
   4.6) With NIS+ how do I find out which machine a client is bound to?
   4.7) Ypcat doesn't work on the netgroup table on a NIS+ server, why?
   4.8) Why is rpc.nisd such a memory pig according to ps?
   4.9) How do I tell my NIS+ server to service DNS requests from
.4.x clients?
   4.10) How can I have multiple addresses per interface?
   4.11) Solaris 2.x supports filesystem sizes up to 1TB.  Will this
.give interoperability problems with NFS?
|  4.12) Where can I get an SNMP agent for Solaris?
| *4.13) How can I use full-duplex ethernet?
| +4.14) Where can I get BOOTP/DHCP for Solaris?

 5. TROUBLE SHOOTING
   5.1) The Solaris 2.x application XX fails with a mysterious error condition.
   5.2) In Solaris 2.5 nm is slow or dumps core.
   5.3) Why can't I run Answerbook on a standalone machine?
   5.4) Why can't I display Answerbook remotely?
   5.5) Why can't I run filemgr, I get ``mknod: permission denied''?
   5.6) Why do I get isinf undefined when linking with libdps on Solaris 2.3?
   5.7) I can't get PPP to work between Solaris 2.3 and other platforms.
   5.8) Using compat mode for passwd doesn't work in 2.3?
   5.9) Why do I get __builtin_va_alist or __builtin_va_arg_incr undefined?
   5.10) My machine hangs during the boot process.  It seems related to ps.
   5.11) Syslogd doesn't seem to log anything.
   5.12) I get ``Invalid client credential'' when mounting filesystem on
.Solaris client from non-Sun fileserver.
   5.13) After upgrade to 2.4, ls on NFS mounted directories hangs.
   5.14) After installing patch 101945-xx, I have NFS problems (ksh looping).
   5.15) I messed up /etc/system, now I can't boot.
   5.16) The /etc/path_to_inst file is corrupted, I can't boot.
   5.17) TCP/IP connections time out too soon, especially on slow links.
   5.18) Sendmail connection to non-Unix hosts don't work.
   5.19) Solaris 2.x can't set up any TCP/IP connections to certain hosts.
   5.20) I read 5.19, but I still have connectivity problems.
   5.21) When reading mail on non-Solaris clients of a Solaris mail
.server, or with non-Solaris mail readers, some messages get split
.into multiple messages.
   5.22) Mail/mailx often send reply to wrong user or show wrong sender.
   5.23) One of my users can't login (one some machines).
   5.24) My clients with remote /var (/var/adm) partitions won't boot.
   5.25) Vacation doesn't work reliably in a mixed Solaris/SunOS environment.
   5.26) I have a lot of <defunct> processes.  How do I get rid of them?
   5.27) I get /dev/ptmx: No such device when attempting to telnet/rlogin in.
   5.28) ld bails out with msync errors.
   5.29) su responds with "Sorry" and doesn't prompt for a password.
| *5.30) Why can't I install 2.4 from a non-Sun CD while I could do so with 2.3?
   5.31) ifconfig can't find my network interface
   5.32) I have an application that compiled fine, but when I run it I get:
.fatal: libfoo.so.2: can't open file: errno=2
   5.33) Motif programs dump core almost immediately.
   5.34) cc complains that "language optional software package not installed".
   5.35) thr_create and other thread functions always return -1
   5.36) Solaris 2.4 is getting slower over time/seems to have a kernel
.memory leak.
   5.37) Why do I get ``Unable to install/attach driver 'xxx''' messages?
   5.38) I can't run nfs: netdir_getbyname failure, /dev/udp: bind problem
   5.39) Why do I get ``named[]: rt_malloc:  memdebug overflow'' errors?
   5.40) Ld dumps core on Solaris/x86
   5.41) In Solaris 2.4 my TCP performance is extremely poor.
   5.42) Solaris 2.4 in.tftpd is terribly slow.
   5.43) I get "df: Could not find mount point ..."
| *5.44) I changed root's shell, now I can't login.
   5.45) When linking C++ programs, I get "_ex_keylock" undefined.
   5.46) My NFS server hangs when I get filesystem full/over quota errors.
   5.47) OpenWindows fails with "Binding Unix Socket: Invalid argument"
|  5.48) Why is Xsun such a memory pig, especially on the SX, S24 and FFB?
   5.49) Solaris 2.5 and Solaris 2.4 patch 101945-34+ have poor TCP performance
.over slow links.
   5.50) After install x86 patch 101946-29, I have problems with sockets and
.TCP/IP throughput.
   5.51) Du and ls show funny block counts on NFSv3 mounted filesystems.
   5.52) When I halt/reboot my system I get "INIT: failed write of utmpx entry"
   5.53) Patch installation often fails with "checkinstall" errors.
   5.54) Why do I get a CPU-bound rpc.ttdbserverd process?
   5.55) What is /proc?  Can I safely remove the large files there?
| *5.56) What does "named[XX]: Lame server on 'hostname' ...." mean?
| *5.57) I installed Solaris on a big disk, but now booting fails.
|  5.58) My Ultra shuts down with "WARNING: THERMAL WARNING DETECTED!!!"

 6. SOFTWARE DEVELOPMENT
   6.1) Where is the C compiler or where can I get one?
| *6.2) What about the linker, the assembler and make?
   6.3) Where has ranlib gone?
   6.4) What do I need to compile X11R5?
   6.5) I can't compile X11R6 on Solaris 2.4
   6.6) X11R6 on Solaris 2.4 won't run.  Xinit dies with "User Signal 1".
.Xterms won't die. Dired doesn't work in emacs-19.
   6.7) I get undefined symbols when compiling R6 in Solaris 2.2.
   6.8) After compiling X11R6 with gcc 2.7.0, X programs won't find their
.libraries.
   6.9) How can I run X11R6 on my SS4 w/ TCX?
   6.10) Can I run X11R6 on my SX, ZX, TCX or FFB?
   6.11) I can't get perl 4.036 to compile or run.
   6.12) I can't get sockets to work with perl.
   6.13) I have problems compiling MH 6.8.3
   6.14) I can't get XV 3.x to compile or run correctly.
   6.15) What happened to NIT? What new mechanisms exist for low-level
.network access?
   6.16) Where are all the functions gone that used to be in libc?
   6.17) I'm still missing some functions: bcopy, bzero and friends.
   6.18) Can I use the source compatibility package to postpone porting?
   6.19) Why doesn't readdir work?  It chops the first two characters of
.all filenames.
   6.20) Why do I get undefined symbols when linking with curses/termcap?
   6.21) Where are the Motif includes and libraries?
   6.22) When I call semctl(), my program crashes.  It works fine elsewhere.
   6.23) Traceroute to Solaris 2.x machines gives many timeouts.
   6.24) I have problems linking my application statically.
   6.25) I get '"/usr/platform/SUNW,Ultra-1/lib/libc_psr.so.1": not in
.executable format: format not recognized' from gdb on my Ultra.
|  6.26) Does Solaris have problems with dates in the year 2000 and after?
| +6.27) I can't seem to get gcc to work under Solaris 2.6
| +6.28) Gdb doesn't fully work on Solaris 2.6.
| +6.29) I can't get gdb to compile with Sun's C compiler

 7. ACKNOWLEDGEMENTS

1. GENERAL

1.1) What's Solaris anyway?

    Solaris(tm) is Sun's name for their UNIX-based user environment,
    including the UNIX(tm) operating system, window system (X11-based),
    and other stuff too.

    Solaris 1.x is a retroactive (marketing?) name for SunOS4.1.x (x>=1),
.    a version of UNIX that is BSD-like with some SVR4 features,
.    along with OpenWindows 3.0.
    Solaris 2.x (which is what most everybody means by "Solaris")
.    includes SunOS5.x, which is an SVR4-derived UNIX,
.    along with OpenWindows 3.x, tooltalk, and other stuff.
    (See 1.5 for a chart with more info)

1.2) Why should I upgrade?

    Solaris 2 is more compatible with the rest of the UNIX industry.
    Other major UNIX vendors including IBM, HP, SGI, SCO, and others
    are based on System V rather than on BSD (though some of them
    are on SVR3, not SVR4). All but one commercial PC-based UNIXes
    are System V based (and mostly SVR4); the only commercial exception
    is from a small but interesting firm called BSDI.

    Solaris 2 is where Sun has been putting almost all its development
    for the last few years now. There will be no new development on
    SunOS4; already much of Sun's add-on software is only available
    for Solaris 2. Solaris 2 is the only supported MP OS on all but
    the old 4/6x0-1x0 w/ Ross 605 modules.  All the UltraSPARC systems
    require Solaris 2.x.

    Most Sun software is being released first for Solaris 2.x.

    Solaris 2.3 and above feature a standard X11R5 release of The X
    Window System, a benefit for those who didn't like NeWS or the
    V2/V3 OpenWindows server. (It's still called OpenWindows, but it is
    the X11R5 server with Adobe DPS added in).  It is as fast or faster
    than MIT R5 or XC R6 (depending on the platform) and supports all
    Sun graphics hardware.

    Solaris 2 is more standards-compliant than Solaris 1/SunOS 4.

1.3) Should I move to Solaris 2.x now, or later, or never?

    That depends - on you, your situation, your application mix, etc.
    Some year SunOS4.1.x will go the way of the 3/50 - it'll still
    be around, but Sun will no longer support it.

    You don't have to upgrade immediately, but you should be
    planning your upgrade path by now.

1.4) What is Solaris 2? Is it really SVR4 based?

    Solaris 2 is an "operating environment" that includes the
    SunOS 5.x operating system and the OpenWindows 3.x window
    environment.

    SunOS 5.x is based on USL's SVR4.0. SVR4.0, in turn, was
    developed jointly by AT&T and Sun while Sun was developing 4.1.0,
    which is why things like RFS, STREAMS, shared memory, etc.,
    are in SunOS 4.1.x, and why things like vnodes, NFS and XView
    are in SVR4.0. (RFS, by the way, was dropped effective Solaris 2.3).

|*1.5) What machines does Solaris 2.x run on?

    Solaris 2.0 only ran on desktop SPARCstations and a few other Sun
    machines.

    Solaris 2.1 and 2.4 and later come in two flavors, SPARC and "x86".

    Solaris 2.1 (and 2.2, ...) for SPARC run on all SPARCstations and
    clones, as well as all models of the Sun-4 family. The old FPU
    on the 4/110 and 4/2x0 is not supported, so floating point
    will be SLOW, but it does work.

    Starting with 2.5 support for machines with kernel architecture
    "sun4" is dropped.  I.e., the machines on which "uname -m" and
    "arch -k" return "sun4"; not the machines on which those commands
    return sun4c, sun4m, sun4u or sun4d.  The unsupported machine
    include the sun4/110 (not to be confused with the SS4 @110MHz),
    sun4/2xx, sun4/3xx and sun4/4xx.  These are all VME based
    deskside/server configurations.

    All version of the SPARC PROMs should work under Solaris 2.x,
    but you can run into the following problems:

.1) No part of the boot partition may be offset more than 1 GB
.into the disk, unless you have a PROM with rev 2.6 or better.
.Note that the number behind the point is not a fraction, it's
.an integer.  Hence 3.0 > 2.25 > 2.10 > 2.9 > 2.1 > 2.0 > 1.6.
.2) If booting diskless, you need a link in the /tftpboot
.directory, "tftpboot -> .".  Admintool will make that
.link automatically.

    A Solaris port for the PowerPC has been completed, and has been released,
    effective Solaris 2.5.1.

    Solaris 2.1, 2.4 and above for x86 have been released to end users.
    It runs on a wide range of high-end PC-architecture machines.
    "High-end" means: 16MB of RAM and an 80486 (or 33MHz or faster
    80386DX).  It will not run on your 4 MB 16MHz 386SX, so don't
    bother trying! Also, floating point hardware (80387-style) is
    absolutely required in 2.1.  Starting with Solaris 2.4 for
    x86, a fp CO-processor is no-longer required, though still
    recommended.  All three buses are supported: ISA, EISA, MCA.
    Some PCI devices are supported, though full bus nexus support
    for PCI is not there.  See also 3.36.

    To summarize all this, Jim Prescott gave this chart, which I've
    updated:

    Solaris SunOS     OpenWin               Comments
    1.0     4.1.1B    2.0
            4.1.1_U1  2.0           sun3 EOL release (not named Solaris)
    1.0.1   4.1.2     2.0           6[379]0-1[24]0 MP
    1.1     4.1.3     3.0           SP Viking support
    1.1C    4.1.3C    3.0           Classic/LX
    1.1.1   4.1.3_U1  3.0_U1        4.1.3 + fixes + Classic/LX support
    1.1.1 B 4.1.3_U1B 3.0_U1        1.1.1B + SS5/SS20 support
    1.1.2   4.1.4     3_414         The "final" 4.x release (SS20 HS11)

    2.0      5.0       3.0.1         sun4c only
    2.1SPARC 5.1       3.1           Dec '92
    2.1 x86  5.1       3.1           May '93
    2.2SPARC 5.2       3.2           May '93
    2.3SPARC 5.3       3.3           Nov '93
                            OpenWin 3.3 is X11R5 based: Display
                            PostScript instead of NeWS, no SunView.
                            It is still primarily OPEN LOOK.
                            The Spring 1995 OpenWin will be Motif
                            and COSE-based.
...    Statically linked BCP support
    2.3 edition II SPARC    Special Solaris 2.3 distribution for
                            Voyager and SparcStation 5
    2.3 hardware 5/94 SPARC ??
    2.3 hardware 8/94 SPARC Supports S24 (24 bits color for SS5),
                            POSIX 1003.2, Energy Start power management
                            and SunFastEthernet + patches.
    2.4       5.4      3.4  From this moment on, the SPARC and x86
                            releases are in sync. Q3 '94
                            Adds motif runtime and headers (not mwm).
    2.4 hardware 11/94      First SMCC release of 2.4
    2.4 hardware  3/95      Second SMCC release of 2.4 (includes support
                            for booting from SSA)
    2.5       5.5      3.5  UltraSPARC support, PCI support.
                            NFS V3, NFS/TCP, ACLs, CDE, Sendmail V8
                            name service cache, dynamic PPP
                            Posix threads, doors (new IPC mechanism)
                            many "BSD" type functions back in libc,
                            many "BSD" programs back in /usr/bin.
                            mixed mode BCP support (e.g., apps only
                            dynamically linked against libdl.so)
    2.5 hardware 1/96       Creator3D support (Creator3D/FFB+ is not
...    supported in 2.5 11/95, though the files
...    are present but of unsupported,
...    "mostly works", beta quality)
    2.5.1                   Ultra-2 support, Ultra-Enterprise
...    server support.  Large (32bit UID)
...    support.  64bit KAIO (aioread64/aiowrite64),
...    3.75 GB of virtual memory.
...    Pentium/Pentium Pro optimizations.
...    (upto 25% for certain database apps)
...    Ultra ZX support.
|...    Initial and last PowerPC desktop release.
|   2.6       5.6      3.6  Largefiles, JVM + JIT, Hotjava,
|...    Web based answerbook, BOOTP/DHCP, SNMP agents,
|...    VLSM, in-kernel sockets, NTP, PAM,
|...    CDE 1.2 as default desktop.

1.6) Will my old applications from 4.1.x run on Solaris 2?

    There is quite a bit of support in SunOS 5.x for running 4.1.x
    binaries in an emulation mode called "Binary Compatibility"
    (BCP).  This works by dynamically linking the 4.1.x binaries
    with a shared library that emulates the 4.1.x binary interface
    on top of 5.x, so there is some overhead.

    In Solaris 2.2 and earlier, the programs needed to be
    fully dynamically linked.

    In Solaris 2.3 and 2.4 fully statically linked programs are
    supported as well.  However, they won't obey nsswitch.conf, but
    use the standard "use NIS if present, fall back to files" approach
    of SunOS 4.x.  Those programs may therefor require a "passwd:
    compat" line and will only talk to NIS (or NIS+ in emulation mode)
    or read from files.

    Starting Solaris 2.5, mixed mode (partly static/partly dynamic)
    executables are supported.  Whether those programs will use
    /etc/nsswitch.conf depends on precisely how much was dynamically
    linked.

    Be aware, though, that Sun may drop the binary compatibility
    package some year.  Try to wean yourself and your users from
    depending on it, even if it means beating on your software
    vendors to offer "native" Solaris2 applications.
    But this will happen later, rather than sooner.  Sun has not
    yet announced End-of-Life of this feature.

|1.7) Will my SPARC binaries run unchanged on UltraSPARC machines?

    Yes.  One of the most important goals of the UltraSPARC project
    was *full* binary compatibility with existing SPARC
    hardware and software.

    If it isn't compatible, it's a bug!

    There are some things you should keep in mind though: if you
    broke the rules but got away with it in the previous generations
    of SPARC machines, your luck may just have run out.

    When developing the UltraSPARC it was discovered that some code
    generators didn't leave all "reserved" bits in opcodes zero.
    Such instructions are either illegal instructions which are trapped
    and fixed in the UltraSPARC kernel or they are legal V9
    instructions which will modify the program behaviour.  All such
    programs can be run through "cleanV8", a program designed
.    <http://www.sun.com/smcc/solaris-migration/tools/tools.html#sunclnv>
    to correct the bogus instructions.

    No instructions of the second category have been found, so even without
    "cleanV8" you should be safe.

    Another thing is the memory map on UltraSPARC, some applications
    use an mmap(MAP_FIXED) call with an address that is illegal to use
    on UltraSPARC.  Such calls are inherently non-portable.  Such
    applications are relatively rare.  One such applications is MAE,
    which should work again after "setenv MAE_NOMMAP_ENGINE".

    A third problem discovered is in device drivers that copy data
    from/to userland directly, bypassing copyin(9f)/copyout(9f).  On V8
    SPARCs, such device drivers would work most of the time, but fail
    mysteriously with panics when the system is stressed and page
    mappings disappear; but on the UltraSPARC the drivers will fail
    always.  The kernel will panic and will tell you in which
    module the panic occurred.

1.8) Will my old applications from SVR3 on the 386 run on Solaris 2/x86?

    As with SPARC, there is an emulation mode that should run the
    majority of well-behaved SVR3 and Xenix binaries.  Most
    SVR3 stuff appears to work under Solaris 2.4.

    Applications from any other vendor's standards-conforming
    386/486 SVR4 should also run.

    However, some vendors have made incompatible changes to their
    SVR4 release and programs linked on those versions may not work.
    Future versions of Solaris 2.x for Intel will address some/most
    of those incompatibilities.  Unixware is one of the offenders.

1.9) Where has the XXX command gone now?

    There are too many of these changes to include in this FAQ, but
    here are some key ones:

    a. locations are often different 
.     whoami         /usr/ucb/whoami
.     make           /usr/ccs/bin/make
.     hostid         /usr/ucb/hostid
.     hostname       /usr/ucb/hostname (or use uname -n)


    Note that the last two commands are back in /usr/bin in
    Solaris 2.5.

    b. some old commands don't exist or have replacements

.     pstat -s       swap -s  (how much swap space?)
.     dkinfo         /usr/sbin/prtvtoc raw_dev_name
.     trace          truss
.     mount -a       mountall
.     exportfs       share
.     bar            cpio -H bar (read only)

    This information can be found in the Solaris 2.x Transition Guide -
    Appendix A (commands), Appendix B (system calls), Appendix C (files).

    This guide has undergone some changes from 2.0 -> 2.1 and beyond.
    Several manuals have ended up being combined into this single
    manual. This manual discusses administrative transition and
    developer transition issues.

    The command "whatnow" (for Solaris 2.x) is included in the
    "Admigration Toolkit" package (see below). The Admigration
    toolkit can be obtained from:

.    opcom.sun.ca:/pub/migration_tools/SUNWmigr.tar.Z
.    Admigration toolkit HTML documentation/code
.    <http://www.sun.com/smcc/solaris-migration/tools/tools.html#sunmigr>

    Sample output:
.% whatnow hostname
.hostname                                        4.x command only
.hostname        /usr/ucb/hostname               part of SCP package
.hostname        /usr/bin/uname -n               alternate command

    The whatnow command is limited in that it may point to
    one command which may only implement a subset of the old
    command (e.g., pstat points to sar, while pstat -s is identical
    to swap -s)

1.10) When I upgrade, should I use SunInstall "upgrade", or start over?

    You can't do a SunInstall "upgrade" from 4.1.x to Solaris2.
    You can use the Admigration toolkit (q.v.) to help you move
    from SunOS 4.1.x (Solaris 1, actually) to Solaris 2.

    If you're moving from Solaris 2.1 to 2.2, or 2.2 to 2.3, ...,
    then you can use "upgrade" to preserve your existing partitions
    and local changes (including pkgadd!!), though it runs very
    slowly (about 1.5-2x the time for a reinstall) and does require
    that you have enough free space in / and /usr - make these big
    when you first install!  If you run out of space in one of
    your partitions, you can always remove some components.  Those
    will not be upgraded and can be installed elsewhere after
    initial upgrade (e.g., you can remove OW, Xil, Dxlib, manual
    pages, etc)

    There is no need to backout patches before upgrading.
    In 2.2, the system would back them out for you, in 2.3 it
    won't back out the patches but removes them without a trace.

    The upgrade doesn't work as well as a full install.
    E.g., the upgrade from 2.x (x<3) to 2.3 will leave
    aliases for all your ptys in /devices/pseudo.

1.11) Is Solaris 2.x reliable/stable enough to use?

    The consensus seems to be that yes, it is, for many applications
    and most users. Your mileage may vary.

    Binary compatibility was much improved in 2.3.  That will help
    transition somewhat.  The performance of 2.3 is adequate, though
    some parts of the system are still slower than SunOS 4.1.x.
    Solaris 2.3 is much more stable on MP machines than 2.2.
    The Solaris 2.3 version of OpenWindows is much faster and much
    more stable than the versions shipped with SunOS 4.1.x.

    Solaris 2.1 and earlier should really be avoided.  Solaris 2.2
    should be avoided too, but some people need to stick to it
    until some applications get ported (2.2 is the last release
    with NeWS).

    Solaris 2.3 still has some problems on high-end MP systems with
    large numbers of interactive users.  Solaris 2.4 and Solaris 2.5
    have delivered increasingly more stable and more scalable multi
    processing.

1.12) Why do some people dislike Solaris2?

    There is a number of reasons why people dislike Solaris.

    1) Change.  In general people dislike change.  Change requires
    re-learning and retraining.  Old system administration practices
    no longer work.  Commands have been replaced by other commands,
    some commands behave differently.  And they ask why the change was
    necessary.  SunOS 4.x worked for them.

    2) Lack of migration support.  Sun did not provide a lot of
    tools to ease migration.  Many applications wouldn't run in the
    binary compatibility mode.  The source compatibility mode was
    probably compatible with some OS, but it certainly wasn't SunOS.
    Lots of public domain and third party stuff that was needed wasn't
    immediately available for Solaris.  NIS+, buggy, resource hungry
    and unstable replaced NIS in incompatible ways.

    3) Missing functionality.  When people migrate, at first they
    don't tend to notice new functionality.  Instead, they stumble
    upon missing functionality such as screenblank, clear_colormap
    and the like (but see 3.21).  And perhaps worst of
    all, no C compiler, not even a crippled one.

    4) Slow and buggy.  The initial Solaris releases didn't perform
    at all well and were extremely unstable.  This has improved
    drastically, with Solaris 2.5 being stable and quick, even
    without many patches.

|*1.13) Why do some people *like* Solaris2?

    There are improvements in Solaris 2.x.

    1) OpenWindows 3.3+ (in Solaris 2.3+).  Includes X11R5 and
|   Display PostScript.  X11R6 in Solaris 2.6.

    2) Motif & CDE.

    3) ANSI-C and POSIX development environment.

    4) POSIX threads (2.5)

    5) POSIX and X/OPEN command environment

|   6) UNIX 95 conformance.

|   7) Posix shared memory and semaphores (2.6)

|   8) Multi-threaded kernel and real threads.

|   9) Real-time feature in the kernel

|   10) Faster clock ticks (optionally 1000Hz in 2.6)

|   11) Large files (2.6)

|   12) True multi-processing.

|   13) Goodies: vold, admintool and Wabi.

|   14) Easy patch installation/administration through installpatch.

|   15) All software in easy to manage "packages".

|   16) Power management software.

|   17) Access control lists

|   18) NFS Version 3 and NFS over TCP (Solaris 2.5+).

|   19) A better automounter, autofs (not more /tmp_mnt and symlinks).

|   20) Jumpstart/autoinstall.

|   21) Better MP support.

|   22) Faster networking (ATM, fastethernet).

1.14) What is Sun doing to help me migrate?

    Sun has recently started several projects to aid in the transition.
    Their WWW starting point is:

    Solaris Migration Initiative home page
.    <http://www.sun.com/smcc/solaris-migration/>

    The project is a combination of new and existing efforts and includes:

    1) Porting PD software to Solaris 2.x
    2) Solaris Migration Tool: (formerly known as Pipeline tool) a tool
    to help you port your code.
    3) Admigration Toolset.  Tools to help you convert your SunOS 4
    environment and to help you adjust to the new Solaris 2.x environment.
    4) Appmap: a tool to simplify application administration in a mixed
    SunOS 4.x/Solaris 2.x environment
    5) Solaris Transition CD
    6) Native Solaris NIS
    7) LP tools (simplified LP administration through NIS)

|1.15) Can I use my SunOS 4 disks on Solaris 2.x?

    Yes you can.  The on disk format in Solaris 2.x isn't
    different from SunOS 4.1.x, as long as they've been formatted
    under SunOS 4.1.x.  Disks formatted on older fses need to be converted
    with "fsck -c".  If "dumpfs | head" (SunOS 4) or "fstyp -v | head"
    (Solaris 2) lists "format dynamic" as one of the first lines, the
    disk does not need to be converted.

    UIDs > 60002 may give problems when moving disks from SunOS 4.x
    to Solaris 2.x.  This is fixed in a Solaris 2.5.1 which has
    MAXUID defined as 2147483648.  Note too that UID and GID 60001
    and 60002 have been defined as nobody and noaccess on Solaris 2.x.
    If the target SunOS 4 system uses such IDs, you need to renumber
    them to avoid the collision

    Moving disks the other way around may give problems: Solaris 2.5
    supports on disks ACLs, and when MAXUID in 2.5.1 is increased
    beyond 65535, that will give added difficulties.

1.16) How can I enable System V IPC? Ipcs says it isn't configured in.

    There's nothing you need to do to enable System V IPC, but on boot
    up "ipcs" always says:

.IPC status from <running system> as of <date>
.Message Queue facility not in system.
.Shared Memory facility not in system.
.Semaphore facility not in system.

    This just means that no one has yet used the Message Queue/Shared Memory
    or Semaphore facility yet.  They'll be loaded on first use.

    If you really want to have them loaded at boot time, add the
    following to /etc/system:

.forceload: sys/msgsys
.forceload: sys/semsys
.forceload: sys/shmsys

|2. SOURCES OF INFORMATION

|*2.1) How can I RTFM when I don't have it anymore?

    "RTFM" is an old saying: Read The "Fine" Manual.  Sun still
    sells printed manuals, but doesn't automatically distribute
    them.  As with all real UNIX systems, you do get a full set of
    online "man" pages. A smaller, lighter, bookshelf-friendly :-)
    set of CDROMs called "The AnswerBook"(tm) contains all the printed
    documents in machine-readable (PostScript) form, with hypertext
    capabilities and a keyword search engine. 90% of your
    introductory questions are answered therein!

    In Solaris 2.x the Answerbook set gets increasingly more
    divided into pieces.  It is currently split over a number of CDs,
    currently (2.5.1):

.Solaris 2.x CD:
.    Solaris 2.x User AnswerBook

.Solaris Desktop 1.x
.    Wabi 2.x Answerbook
.    Solaris Common Desktop Environment AnswerBook 1.0.x

.Updates for Solaris Operating Environment 2.x
.    Solaris 2.x on Sun Hardware Answerbook

.Server Supplement
.    NSKit 1.2 answerbook
.    Solaris 2.x System Administrator AnswerBook
.    (Solaris 2.5.1 Supplemental System Admin AnswerBook)
.    Solaris 2.x Reference Manual AnswerBook

.Solstice AutoClient & AdminSuite
.    Solstice AutoClient 2.0 AnswerBook
.    Solstice AdminSuite 2.2 AnswerBook

.Solstice Online Disksuite
.    DiskSuite 4.0 AnswerBook

.Solstice Backup
.    Solstice Backup 4.2 AnswerBook

.Solaris 2.x Software Developer Kit
.    All programming manuals.

.Solaris 2.x Driver Developer Kit
.    Device driver developer manuals.

    Only the first two CDs ship with the desktop edition, the third is
    SPARC specific.  The last two CDs are part of two separate
    products; the SDK and DDK.  The rest is server only, though the
    reference manuals are available in nroff source form.

    There is some overlap between CDs.

|   As distributed with 2.1 and 2.2, the Answerbook search engine runs
|   only with the OpenWindows ("xnews") server, not with MIT X11.

|   In Solaris 2.3 through 2.5.1 answerbook uses X extension DPS.  If
|   you are using the MIT server instead of what Sun provides, you'll
|   have to use one of several "answerbook workaround" scripts that are
|   in circulation.  The AnswerBook distributed with 2.3 and later runs
|   with the OW3.3 X11R5+DPS server, so it should display on any
|   X11+DPS server, such as on DEC, IBM and SGI workstations.

|   In Solaris 2.6, answerbooks are distributed in SGML format; they
|   are presented through a special web server which is also able to
|   convert old Postscript answerbooks to HTML on the fly.
|   Sun has a site on the web that has many of the answerbooks
|.    <http://docs.sun.com>
|   available.

    You should buy (or print from within Answerbook) at least the
    reference manual and the System and Network Administration
    books, because if your system becomes disabled you won't be
    able to run the Answerbook to find out how to fix it...

2.2) Why is "man -k" so confused?

    Solaris man uses a manual page index file called "windex" in
    place of the old "whatis" file. You can build this index with
.      catman -w -M <man-page-directory>

    But, in 2.1, this will result in numerous "line too long" messages
    and a bogus windex file in /usr/share/man, and a core dump in
    /usr/openwin/man. (In 2.2, catman works in /usr/share/man, but
    says "line too long" in /usr/openwin/man).  To add injury to
    insult, "man" normally won't show you a man page if it can't find
    the windex entry, even though the man page exists.

    There's a "makewhatis" script in /usr/openwin/man that works
    better than catman. But watch it - by default it searches files
    in /usr/man, not in openwin, and it only looks in some predefined
    man subdirectories. Try changing its "for ..." command to
    "for i in man*", then use it like this:
.      cd /usr/share/man; /usr/openwin/man/makewhatis .
.      cd /usr/openwin/man; /usr/openwin/man/makewhatis .

    Still (!), the openwin windex file is somewhat hosed (try "man
    answerbook" :-( ).  You can always delete the bogus lines manually...
    or, you can alias man to "man -F", forcing it to look for the
    bloody file like you asked.

    But wait, there's more! To see the read(2) man page, you can't
    just type "man 2 read" anymore - it has to be "man -s 2 read".
    Or, alias man to this little script:

.    #!/bin/sh
.    if [ $# -gt 1 -a "$1" -gt "0" ]; then
..    /bin/man -F -s $*
.    else
..    /bin/man -F $*
.    fi

|2.3) What Software is available for Solaris 2.x?

    Most commercial software that ran on 4.x either will run in BCP
    mode, or is available for Solaris 2.x, or is being ported now.
    Solaris 2.3 BCP mode finally supports statically-linked executables.
    Solaris 2.5 BCP mode supports mixed mode (part static, part dynamic)
    executables too.

    You can obtain a list of official 3rd party porting
    commitments, maintained by Sun's "Solaris Demand Center"
    (whatever that is), by sending electronic mail to
    "sparc_products@thegift.sun.com" -- this is an automatic reply
    server.  The list shows what third party applications are currently
    available for Solaris, and lists expected dates for many more.

    Sun's web pages contain a searchable index
.    <http://www.sun.com/sunsoft/catlink/>
    of commercial programs and a link to an outside contractor
.    <http://smc.vnet.net/solaris_2.5.html>
    who gathers data on free and public domain programs.

    A list of freeware (some "public domain", but mostly copyright-
    but-freely-distributable) [as well as commercial software??]
    that has been ported to Solaris 2.x
    is posted monthly to the newsgroup comp.unix.solaris by
    ric@coronacorp.com (Richard Steinberger). Look for this:

.    Subject: Solaris SW list.  Monthly Post.
.    <ftp://sheffield.isl.sri.com/pub/solaris/solaris-sw-list.txt>

    Some software that invariably needs minor tweaking after an OS upgrade
    is included here specially.  It's almost always necessary to recompile
    it after an OS upgrade, but if that still doesn't give a working
    version, make sure you check the archives for the latest version:

    Top - a process monitor
.    <ftp://eecs.nwu.edu/pub/top/>
|   Site carrying the latest version of Top
.    <ftp://ftp.groupsys.com/pub/top/>

    Lsof - list open files
.    <ftp://vic.cc.purdue.edu/pub/tools/unix/lsof/>

    Identd - a daemon that implements RFC1413
.    <ftp://ftp.lysator.liu.se/pub/ident/servers/>

    scsiinfo - a program that lists SCSI devices.
.    <ftp://ftp.cdf.toronto.edu/pub/scsiinfo/>

    sysinfo - a system hardware information program.
.    <ftp://usc.edu/pub/sysinfo/sysinfo.tar.gz>

    If you use gcc, it is important to remember that you must re-run
    fixincludes or re-install gcc after an OS upgrade or you'll be
    compiling with the old include files which will essentially give
    you the above programs as if compiled for a previous OS release.

2.4) What FTP/WWW sites do I need to know about?

    www.sun.com <http://www.sun.com/>
.Sun's own WWW site, contains pointers to Sunsites, patches
.and has lots of info, press releases etc, etc.

    Solaris transition home page
.    <http://www.sun.com/smcc/solaris-migration/>
.Sun's Solaris 2.x migration support

    Solaris 2.x binaries
.    <http://smc.vnet.net/solaris_2.5.html>

    Solaris 2.x/SPARC binaries in pkgadd format
.    <http://sunsite.unc.edu/pub/packages/solaris/sparc/>

    Solaris 2.x/x86 binaries in pkgadd format
.    <http://sunsite.unc.edu/pub/packages/solaris/i86pc/>

    SunSites - Sun sponsored sites.  Lots of good stuff there.
.    <http://www.sun.com/sunsite/>

.Sun SITE AskERIC at Syracuse University - Syracuse
.    <http://ericir.sunsite.syr.edu/>
.Sun SITE Australia at Australian National University - Canberra
.    <http://sunsite.anu.edu.au/>
.Sun SITE Central Europe at RWTH-Aachen - Germany
.    <http://sunsite.informatik.rwth-aachen.de/>
.Sun SITE Chile at Universidad de Chile - Santiago
.    <http://sunsite.dcc.uchile.cl/>
.Sun SITE Czech Republic at Charles University - Prague
.    <http://sunsite.mff.cuni.cz/>
.Sun SITE Denmark at Aalborg University - Aalborg
.    <http://sunsite.auc.dk/>
.Sun SITE Digital Library at University of California at Berkeley
.    <http://sunsite.berkeley.edu/>
.Sun SITE France at Conservatoire National des Arts-et-Metiers - Paris
.    <http://sunsite.cnam.fr/index.html>
.Sun SITE Hong Kong at University of Science and Tech. - Hong Kong
.    <http://sunsite.ust.hk/>
.Sun SITE Hungary at Lajos Kossuth University, Debrecen - Hungary
.    <http://sunsite.math.klte.hu/>
.Sun SITE Italy at University of Milan - Milan
.    <http://sunsite.dsi.unimi.it/index.html>
.Sun SITE Israel at Hebrew University of Jerusalem - Jerusalem
.    <http://sunsite.huji.ac.il/sunsite.html>
.Sun SITE Japan at Science University - Tokyo
.    <http://sunsite.sut.ac.jp/>
.Sun SITE Korea at Seoul National University - Seoul
.    <http://sunsite.snu.ac.kr/>
.Sun SITE Mexico at Universidad Nacional Autonoma de Mexico - Mexico
.    <http://sunsite.unam.mx/>
.Sun SITE Nordic at Kungliga Tekniska Hgskolan - Stockholm
.    <http://sunsite.kth.se/>
.Sun SITE Northern Europe at Imperial College - London
.    <http://sunsite.doc.ic.ac.uk/>
.Sun SITE People's Republic of China at Tsinghua University - Beijing
.    <http://sunsite.net.edu.cn/>
.Sun SITE Poland at Warsaw University - Warsaw
.    <http://sunsite.icm.edu.pl/>
.Sun SITE Russia at  Moscow State University - Moscow
.    <http://sunsite.cs.msu.su/>
.Sun SITE Thailand at Assumption University - Bangkok
.    <http://sunsite.au.ac.th/>
.Sun SITE Spain at Consejo Superior de Investigaciones Cientificas, RedIRIS -  Madrid
.    <http://sunsite.rediris.es/index.html>
.Sun SITE Singapore at National University of Singapore - Singapore
.    <http://sunsite.nus.sg/>
.Sun SITE South Africa at University of the Witwatersrand - Johannesburg
.    <http://sunsite.wits.ac.za/>
.Sun SITE USA at University of North Carolina - Chapel Hill
.    <http://sunsite.unc.edu/>

    Solaris at UMBC - Solaris tips & tricks by Vijay Gill
.    <http://umbc8.umbc.edu/~vijay/solaris/solaris.html>

    ftp.x.org - the master X11 site

    ftp.quintus.com:/pub/GNU - GNU binaries

    ftp.uu.net - UuNet communication archives
    (mirrors abovementioned GNU binaries in systems/gnu/solaris2.3)
.    <ftp://ftp.uu.net/systems/gnu/solaris2.3>

    OpCom. (opcom.sun.ca) - run by Sun Microsystems' OpCom group - lots
    of stuff. Here is some of the stuff that's online: 

    pub/AMToolkit.* - the Administration Migration (4.1.x to Solaris 2)
..      Toolkit

    pub/binaries    - binaries/man pages for Solaris 2.0 native binaries.

    pub/newsletter  - issues of the monthly OpCom newsletter.

    pub/docs        - assorted documentation, papers, and other information.
..    - all of the RFCs

    pub/drivers     - information related to device driver writing under
..      under Solaris 2.0 as well as a skeleton SCSI driver.

    ls-lR.Z         - compressed recursive listing of files available
..      on the server.

    pub/tars        - compressed tars.

    pub/tmp         - place for uploading things to the server.

    pub/R5          - the unadultered MIT x11r5 distribution.

    pub/x11r5       - port of X11r5 to Solaris 2.0, binaries, libraries
..      and headers.  A compressed tar of this tree can
..      be found in tars.


    prep.ai.mit.edu and the GNU mirrors


    Joe Shamblin's x86 site at Duke
.    <ftp://x86.cs.duke.edu/pub/solaris-x86/bins/>

    server.berkeley.edu:/pub/x86solaris - x86 stuff

    ftp.wins.uva.nl

.pub/solaris
.    - where the Solaris FAQ is kept, including an html
.      version.

.pub/solaris/auto-install
.    - fully automated auto-install scripts, including
.      an explanation of exactly what a machine needs when
.      booting the installation, automated patch installation
.      and even post-install updates from your install tree,
.      which gives you an easy way to keep all your Solaris
.      machines in sync.


2.5) What other FAQ's do I need to know about?

    1) Stokely Consulting's list of Sun FAQs
.    <http://www.stokely.com/stokely/unix.sysadm.resources/faqs.s.html#faq.link.sun>
    2) Obsolete, SunOS 4.x only: Sun Computer Administration Frequently Asked Questions
.    <http://aurora.latech.edu:80/sunadminfaq.html>

    3) The "Solaris 2 Porting FAQ"
.    <http://www.cis.ohio-state.edu/hypertext/faq/usenet/Solaris2/porting-FAQ/faq.html>

    4) comp.windows.open-look - Anything related to OpenWindows or the
    OPEN LOOK Graphical User Interface.

    5) The Sun-Managers mailing list FAQ
.    <ftp://ra.mcs.anl.gov/sun-managers/faq>
    maintained by John DiMarco <jdd@cdf.toronto.edu>.

    6) See also the "Solaris SW list. Monthly Post" above and the
.    "whatlist" file.

2.6) What mailing lists should I get?

    First, read all the USENET newsgroups with "sun" in their name :-)

    1) The Florida SunFlash is a "closed" mailing list for Sun owners.
    It contains mostly press releases from Sun and third-party
    vendors.  This list contains information on conferences such as
    the Solaris Developer's Conference as well.  It is normally
    distributed regionally - to find out about a mail point in your
    area, or for other information send mail to info-sunflash@Sun.COM.

    Subscription requests should be sent to sunflash-request@Sun.COM.
    Archives are on solar.nova.edu, ftp.uu.net, sunsite.unc.edu,
    src.doc.ic.ac.uk and ftp.adelaide.edu.au

    2) The Sun Managers list is an unmoderated mailing list for
    *emergency-only* requests. Subscribe and listen for a while,
    and read the regularly-posted Policy statement BEFORE sending
    mail to it, and to get a feel for what kinds of traffic it carries.
    Write to sun-managers-request@eecs.nwu.edu.

    3) The solaris x86 list.  Subscribe/unsubscribe by sending a message
    with subscribe/unsubscribe in the *BODY* of the message to
    solaris-x86-request@mlist.eis.com.  A digested version of the list
    is also available.  To subscribe send an email message to
    solaris-x86-digest-request@mlist.eis.com.
    There's also an archive of this list.
|.    <http://www.eis.com/html/listmain.html>

    4) The Sun Security Bulletin announcement mailing list.
.    Low volume, announcement only list.
.    Subscribe by mailing security-alert@sun.com with subject
.    "SUBSCRIBE cws user@some.host"


2.7) What books should I read?

    O'Reilly & Associates specializes in UNIX books.  Their "UNIX
.    <http://www.ora.com>
    In A Nutshell" has been updated for SVR4 and Solaris 2.0.  Get
    their catalog by calling 800-998-9938 (1-707-829-0515) 7AM to
    5PM PST.

    SunSoft Press carries books specific to Solaris 2. Look for the
    inset with your End User Media Kit that lists the most relevant ones.

    Prentice-Hall has reprints of much of the AT&T documentation.
    I'm not sure how much of this you need - a lot of the same
    material is in the Answerbook (see above).

2.8) What hardware is supported by Solaris 2.x for Intel?

    The complete and often updated list Solaris x86 hardware options
    can be obtained by sending an email message without subject/body
    to:

.    x86hcl@sun.com.(ascii)
.    x86hcl.ps@sun.com.(postscript)

    or
.    x86-hwconfig@Cypress.West.Sun.Com

    There's also an online version of all the lists.
.    <http://access1.sun.com/certify/hcl.html>


*2.9) What is Wabi?

    Wabi is Sun's MS-Windows-under-unix emulator.
    The Wabi faqs can be obtained by sending an empty message to:

.    wabi-questions@East.Sun.com

    The list of current Wabi apps can be obtained by mailing:

.    wabi-apps@East.Sun.COM

    Applications that execute a lot of x86 code, run fastest on
    Solaris 2.x_86, as no x86 emulation needs to be done.
    Applications that are more windows intensive will run
    better on machines with faster graphics hardware.

    The currently shipping version of Wabi is Wabi 2.2, which
    ships with Solaris 2.5.1.

|   Wabi only supports MS Windows 3.1 applications.  Plans to support
|   Windows 95 have been shelved.

    Wabi will not be made available for SunOS 4.1.x.

    Reports indicate that Wabi support will be dropped by Sun
    and replaced by some other PC on Sun product.

2.10) I'm running into some limits of SunOS 4.x, will upgrading to
    Solaris 2.x help?

    The answer depends on the limit you run into.

    Solaris 2.x supports filesystems upto 1TB, SunOS 4.x requires
    ODS 1.0 to support filesystems over 2GB.
    Solaris 2.x (x<=5) doesn't support files > 2GB yet, 
    because of limitations in NFSv2 (32 bit offsets only).

    Solaris 2.x supports a virtually unlimited number of open
    filedescriptors, SunOS 4.x only supports 256 (default) or 1024
    (with Sun DBE 1.x).

    Solaris 2.x supports an unlimited number of pseudo terminals.

    Solaris 2.x supports more SCSI disks.

    Solaris 2.x limits can be tuned in /etc/system, requiring just a
    reboot.  SunOS 4.x limits need to be tweaked in the config file and
    a new kernel needs to be build and installed.

    NOTE: when the above says "unlimited", it just means that there is
    no "hard" limit, but performance may degrade over certain values.
    E.g., setting the number of available fds very high, will cause
    programs that loop closing all fds to be very slow in starting.


3. SYSTEM ADMINISTRATION

3.1) How much disk space do I need to install Solaris 2?

    A full install of 2.2 is supposed to be 164 MB, but that doesn't
    include swap. Here is a net exchange between Casper Dik and Gil Tene:

    In article <1993Apr2.083549.19177@fwi.uva.nl>, Casper writes:
    |> >How much disc space does SOLARIS take up ? That is should we buy a
    |> >424MB disc or get a 1Gb disc to put it on :-)
    |>
    |> Solaris 2.x takes about as much diskspace as SunOS 4.x:
    |>
    |> Partition/Slice Solaris SunOS
    |> /            10MB     8MB
    |> /usr         78MB    90MB
    |> /var         10MB    10MB
    |> /usr/openwin 83MB    83MB

    Gil replies:
    On my system, with a full Solaris installation (EVERYTHING selected)
    + gnu's binary stuff for solaris (off of the Catalyst CD) installed
    in /opt I see a similar situation to the above plus :

    16852   /opt/SUNWabe
    19      /opt/SUNWcg12
    7968    /opt/SUNWdiag
    721     /opt/SUNWgt
    7740    /opt/SUNWits
    14609   /opt/cygnus-sol2-1.0

    (output from "du -k -s /opt/*")

    - SUNWabe is the end user answerbook stuff.  (vi, mail, Deskset tools
      etc, etc)

    - SUNWcg12 is (obviously) cg12 support.

    - SUNWdiag is obvious too.

    - SUNWgt is support for gt boards.

    - SUNWits is the xgl3.0 library (it has libPEX5.so.1 in there too).

    - cygnus-sol2-1.0 is the gcc2.0+tools stuff. I have gcc2.3.3 on
      another partition and that takes about the same space as 2.0 does.

    Another important note : The full Solaris 2.1 answerbook takes up 164MB
    on disk. I highly recommend installing it and not using it off the
    CDROM drive. It's much more usable (faster) this way. And it always
    stays around -- even when you have something else in the CDROm drive.

3.2) How can I convert all my local changes that I've made over the
    years into their corresponding forms on Solaris 2?

    1) Do it by hand. You did document every single change and
    check it into RCS, didn't you?

    2) Automate it, using the AMToolkit (Administration Migration
    Toolkit) from the OpCom FTP server (q.v.)!

3.3) What are "packages"?

    A SVR4 mechanism for "standardizing" the installation of
    optional software. Most vendors are expected to use this
    format for distributing add-on software for Solaris 2.x.

    Packages can be installed/deinstalled with pkgadd/pkgrm which
    are standard SVR4 items, or with swm (CRT) or swmtool (GUI-based)
    which are provided only in Solaris 2.

    Note that the "pkg" system keeps lots of files in /var/sadm/install,
    and in particular the file "contents", which is hundreds of KB,
    and that there are two copies of it while pkgadd is running, so you
    needs lots of free space where /var is, typically the root.
    This file must be kept around if you want, for example, to use
    pkgrm to remove a package, or pkgchk to verify months later that
    all of a a package's files are still intact.

    Summary of pkg* commands:

.    pkginfo <pkg>   - test for presents of package.
.    pkgadd -d /<cdrom>/Solaris_2.3 <pkg ...>
...    - add missing packages
.    pkgrm <pkg ...> - remove packages.
.    pkgchk -q <pkg> - test for existence of package
.    pkgchk <options> [pkg] - check installed packages for
.    integrity.

|*3.4) Why can't I write in/mount over /home?

    SunOS 5.x is delivered with the "automounter" enabled. The
    automounter is designed for NFS sites, to simplify maintenance of
    the list of filesystems that need mounting. However it is a burden
    for standalone sites.

    The automounter takes over /home and in effect becomes the NFS
    server for it, so it no longer behaves like a normal directory.
    This is normally a Good Thing as it simplifies administration if
|   everybody's home directory is /home/<username>, regardless of their
|   physical location.

|   If you want to continue to use the automounter, edit /etc/auto_master
|   and comment out the line starting with "/home".  Then run the
|   "automount" command which will cause automountd to reload the maps.

|   To kill it off for standalone or small networks running Solaris 2.3
|   or later, you can stop automountd by running "/etc/init.d/autofs
|   stop".  Prevent it from starting at boot time by renaming the file
|   /etc/rc2.d/SXXautofs to /etc/rc2.d/sXXautofs, where XX are two
|   digits depending on the OS release. (If you change your mind, just
|   rename it back)

|   In Solaris 2.2, the procedure is different.  You need to comment
|   out the three lines in /etc/init.d/nfs.client that start "if" (from
|   the if to the fi!!), and reboot (Solaris 2.2)

    To learn about it, read the O'Reilly book "Managing NFS and
    NIS", or ftp the white paper 'The Art of Automounting".  from
    sunsite.unc.edu in the directory /pub/sun-info/white-papers.

3.5) Why can't I access CDs or floppies?

    Solaris 2.2 introduced a new scheme for automatically mounting
    removable media. It consists of a program "vold" (volume daemon) which
    sits around watching for insertions of floppies and CD's,
    handles ejects, talks to the file manager, and invokes a second
    program called "rmmount" (removable media mounter) to mount the disk.

    Note that on most SPARCstations, you must run "volcheck" whenever
    you insert a floppy, as the floppy hardware doesn't tell SunOS that
    a floppy was inserted and polling the drive would wear it out
    pretty quickly.

    Advantages of this scheme:
    - no longer need root; users can mount and unmount at will.
    - can do neat tricks like automagically start "workman" or
      other Audio CD player when audio CD inserted.
    - extensible - developers can write their own actions.

    Drawbacks:
    - can no longer access /dev/rfd0 to get at floppy; must use
      longer name like /vol/dev/rdsk/floppy0
    - similarly, CD's get mounted on /cdrom/VOLNAME/SLICE, e.g.,
      /cdrom/solaris_2_2/s0 is slice 0 of the Solaris 2 CD
      (nice that it does mount all the partitions, though!).

    To read or write a non-filesystem floppy (tar, cpio, etc),
    put in the diskette and run "volcheck" from the commandline or
    click "Check for Floppy" in the filemgr to get it noticed; then access
    /vol/dev/rfd0/unlabeled  (e.g. "tar tvf /vol/dev/rfd0/unlabeled").

    [Solaris 2.3 and later: /vol/dev/rdiskette0/unlabeled, or
...   /vol/dev/aliases/floppy0.]

    If you want the old behavior, remove the /etc/rc2.d/S*volmgt
    link, and reboot.

3.6) Why are there no passwords in /etc/passwd?

    System V Release 4 includes a feature called "shadow passwords".
    The encrypted passwords are moved out into a shadow password file
    (called /etc/shadow in this release) that is NOT publicly readable.
    The passwd file has always been readable so that, for example, ls -l
    could figure out who owns what. But having the passwd encryptions
    readable is a security risk (they can't be decrypted but the bad guy
    can encrypt common words and names etc. and compare them with the
    encryptions).

    The Shadow Password feature is mostly transparent, but if you
    do any passwd hacking you have to know about it!  And DO make
    sure that /etc/shadow is not publicly readable!

3.7) Why can't I rlogin/telnet in as root?

    >... when I try to rlogin as root ...
    >it gives me the message "Not on system console
    >Connection closed.".  What have I left out?

    Solaris 2 comes out of the box a heck of a lot more secure than
    Solaris 1.  There is no '+' in the hosts.equiv.  root logins are not
    allowed anywhere except the console.  All accounts require passwords.
    In order to allow root logins over the net, you need to edit the
    /etc/default/login file and comment out or otherwise change the
    CONSOLE= line.

    This file's CONSOLE entry can actually be used in a variety of ways:

    1) CONSOLE=/dev/console (default) - direct root logins only on console
    2) CONSOLE=/dev/ttya - direct root logins only on /dev/ttya
    3) CONSOLE= - direct root logins disallowed everywhere
    4) #CONSOLE (or delete the line) - root logins allowed everywhere

    /etc/hosts.equiv is still supported, but there is no default.

3.8) How can I have a user without a password?

    In addition to removing the password from /etc/shadow, you need
    to take one of the following steps:

    Edit /etc/default/login and comment out PASSREQ=YES or change it
    to PASSREQ=NO. This allows *all* users to remove their password!

    The second way is to give a particular user no password with the
    following entry in /etc/shadow:

    user::9092:9999:9999::::

|3.9) How can I set up anonymous FTP?

    If you need help, ftp the file "ftp.anon" from
    ftp://ftp.math.fsu.edu/pub/solaris/ftp.anon.

    ftpd(1M) is nearly complete when it comes to setting
    up anonymous ftp.  It only leaves out /etc/nsswitch.conf. [S2.3]

    Additionally, you must make sure that the filesystem ~ftp resides
    on is not mounted with the nosuid option.  This is because the nosuid 
    option also disables the kernel honoring device files which are 
    required in the chroot environment for ~ftp.

    For security reasons, it is important that no files under ~ftp are
    owned by ftp.  If they are, anonymous users can modify them.

    In Solaris 2.5 and later, you will need to copy /usr/lib/libmp.so.1
    as well as provide a /dev/ticlts (for wu-ftpd).

3.10) How can I print from a Solaris 2 (or any System V Release 4) system
    to a SunOS4.x (or any other BSD) system?

    The easiest way would be using the GUI-based Admintool which has a
    Printer Manager that is supposed to be able to do all this and
    more.

    Hmmm, the lp system is totally different than what you're used to.
    The System V Line Printer System is a lot more, well, flexible.
    A cynic might say "complicated".  Here's a very quick guide --
    see the man pages for each of these commands for the details.

    Let's say your Solaris2 workstation is called "sol" and the
    4.1.x server is called "bertha" and you want the printer name
    to be "printer" (imaginative, eh?).

    sol# lpsystem -t bsd bertha             # says bertha is a bsd system
    sol# lpadmin -p printer -s bertha -T unknown -I any
.....    # creates "printer" on "sol"
.....    # to be printed on "bertha"
    sol# accept printer                     # allow queuing
    sol# enable printer                     # allow printing
    sol# lpstat -t                          # check the status

    Finally, if that's your only printer, make it the default:

    sol# lpadmin -d printer

    On some systems you may have to turn on the port monitor.

3.11) Why does lp complain about invalid content types?

    For better or for worse, you need to know about printer content types.
    See the man page for "lpadmin".

    To get transparent mode, try this:

    sol# lpadmin -I any -p printer

3.12) My jobs stay in the queue after printing.

    It's a known bug, and looks fixed in 2.5.
    There's also a number of lpsched patches out for
    Solaris: 101025-xx (2.2), 101317-xx (2.3),
    101959-xx (2.4) and 101960-xx (2.4/x86).
    Make sure you install those.

    Regardless of what other patches you apply, if you have a printer
    connected to your system running Solaris 2.4 or later, and if that
    printer uses NeWSprint software, you must apply patch 102113-xx.
    This patch is included on the Solaris CD in 2.4 and later
    releases.  This patch is also required if you are running Solaris
    2.3 with kernel jumbo patch 101318-55 or later.  Note that this is
    a NeWSprint patch, not a Solaris patch, and hence it will never be
    integrated into any Solaris release.

    "lpstat" on the clients on a regular basis, for some reason
    this clears the old files from the queue directories.

|*3.13) Are there any alternatives to the system V spooler?

|   Sun has a new printing product available, "SunSoft Print Client".
|.    <http://www.sun.com/smcc/solaris-migration/tools/tools.html#sspc>
|   It's bundled with 2.6 and co-shipped with 2.5.

    It has many new features, including printcap-like printer
    configurations that can be shared via NIS, and currently
    the ability to be configured so that lpsched does not have to
    be run anymore on client-only systems (although you still need to
    run lpsched in order for admintool to work.)

    Alternatively, you can get a Solaris port of the BSD lpr system
    from the following FTP site (get lpr-sol2-*.tar.gz):

    ftp.eng.auburn.edu:/pub/doug

3.14) What happened to /dev/MAKEDEV? How do I add devices?

    Device drivers are linked in dynamically. When you add new
    devices, just shutdown the system and do
.    boot -r # use drive spec if not default disk
    to *r*ebuild the /devices and /dev directories.

    If you're just adding a SCSI disk, you don't need to reboot.  Run the
    following script (as root):

    #!/bin/sh
    #
    # add-disk
    #
    #       Runs the commands to make Solaris locate a new disk that
    #       has been plugged in after the system was booted.
    #

    /usr/sbin/drvconfig
    /usr/sbin/devlinks
    /usr/sbin/disks                 # or /usr/sbin/tapes for tapes
    /usr/ucb/ucblinks               # Compatibility links

    exit 0

    Note that this only works if you already have at least one SCSI disk on
    the system.  (This is because the above just makes symbolic links and
    things, it does not load up the SCSI driver kernel modules, etc.)

3.15) Why isn't my tape/cd player or new disk/device recognized?

    Devices must be turned on and present when you configure
    the system.  After adding devices you must boot -r with all
    the devices turned on.  See also 3.14

3.16) What happened to /etc/rc and /etc/rc.local?

    They're now fragmented into 12 million tiny little pieces. Look in
    the following files to get oriented:
.    /etc/inittab - defines which programs init starts and when.
.    /sbin/rcS, /etc/rcS.d/* - booting stuff
.    /sbin/rc2, /etc/rc2.d/*,
..    /sbin/rc3, /etc/rc3.d/* - stuff for multi-user startup.
    Note that all files in /etc/rc*.d/* are hardlinked from
    /etc/init.d (with better names), so you should grep in there.

    There are many "run levels" to the System V init; the run
    level 3 is normally used for "multi user with networking."

    When executing the scripts in an /etc/rc?.d directory, the
    K* scripts are executed first, followed by the S* scripts.
    Scripts ending in .sh are executed in the same shell and can
    be used to set environment variables used further on in the
    same directory.

    A basic startup script looks like this:

    #!/bin/sh
    # Sample init.d script.
    # Install a copy under /etc/init.d/your-daemon
    # make links to /etc/rc2.d/Sxxyour-daemon (or rc3.d)
    # and /etc/rc[01].d/Kxxyour-daemon.
    # Scripts ending in .sh are executed with the sh "." command.
    # Scripts not ending in .sh are executed as "sh script"

    case "$1" in
    start)
.    #... commands to start daemon ....
.    ;;
    stop)
.    #... commands to stop daemon ....
.    ;;
    esac

3.17) Can't I have /etc/rc.local back?

    No. You can never have rc.local back the way it was. But then, it
    never really *was* purely a "local" rc file. To have a real
    "local" rc file with just your changes in it, copy this file
    into /etc/init.d/rc.local, and ln it to /etc/rc3.d/S99rc.local.
    Put your startup stuff in the "start" section.

    #!/sbin/sh
    # /etc/init.d/rc.local - to be linked into /etc/rc3.d as
    # S99rc.local -- a place to hang local startup stuff.
    # started after everything else when going multi-user.

    # Ian Darwin, Toronto, November, 1992
    # As with all system changes, use at own risk!

    case "$1" in
    'start')
.    echo "Starting local services...\c"

.    if [ -f /usr/sbin/mydaemon ]; then
..    /usr/sbin/mydaemon
.    fi
.    echo ""
.    ;;
    'stop')
.    echo "$0: Not stopping any services."
.    ;;
    *)
.    echo "Usage: $0 { start | stop }"
.    ;;
    esac

3.18) Why are there two versions of shutdown?

    SVR4 (hence SunOS 5.x) tries to make everybody happy. The
    traditional (slow) System V "shutdown" runs all the rc0.d/*
    shell scripts with "stop" as the argument; many of them run
    ps(!) to look for processes to kill. The UCB "shutdown" tells
    init to kill all non-single-user processes, which is about two
    orders of magnitude faster.  In old versions of Solaris (2.2 and
    before) the UCB version did everything it should *except* actually
    halt or reboot.

    If you run a database (like Oracle) or INN, you should
    install a special /etc/rc0.d/K* script and make sure you
    always shutdown the long way.

3.19) When will somebody publish a package of the BSD (4.3BSD Net2)
    "init", "getty", and "rc/rc.local", so we can go back to life
    in the good old days?

    Getty should be easy and was reportedly done at a number of
    sites.  The port monitor isn't everyones favorite. But given
    that you can do much more with the SVR4 init, why would
    you want to change back?  It would be much more trouble than
    it's worth.

3.20) What has happened to getty? What is pmadm and how do you use it?

    I was hoping you wouldn't ask. PMadm stands for Port Monitor Admin,
    and it's part of a ridiculously complicated bit of software
    over-engineering that is destined to make everybody an expert.

    Best advice for workstations: don't touch it! It works out of the box.
    For servers, you'll have to read the manual.
    This should be in admintool in Solaris 2.3 and later.
    For now, here are some basic instructions from Davy Curry.

    "Not guaranteed, but they worked for me."

    To add a terminal to a Solaris system:

    1. Do a "pmadm -l" to see what's running.  The serial ports on the
    CPU board are probably already being monitored by "zsmon".

    PMTAG          PMTYPE         SVCTAG         FLGS ID       <PMSPECIFIC>
    zsmon          ttymon         ttya           u    root     \
.    /dev/term/a I - /usr/bin/login - 9600 ldterm,ttcompat ttya \
.    login:  - tvi925 y  #

    2. If the port you want is not being monitored, you need to create a
    new port monitor with the command

.    sacadm -a -p PMTAG -t ttymon -c /usr/lib/saf/ttymon -v VERSION

    where PMTAG is the name of the port monitor, e.g. "zsmon" or "alm1mon",
    and VERSION is the output of "ttyadm -V".

    3. If the port you want is already being monitored, and you want to
    change something, you need to delete the current instance of the port
    monitor.  To do this, use the command

.    pmadm -r -p PMTAG -s SVCTAG

    where PMTAG and SVCTAG are as given in the output from "pmadm -l".  Note
    that if the "I" is present in the <PMSPECIFIC> field (as it is above),
    you need to get rid of it.

    4. Now, to create a specific instance of ttymon for a port, issue the
    command:

    pmadm -a -p PMTAG -s SVCTAG -i root -fu -v 1 -m \
.    "`ttyadm -m ldterm,ttcompat -p 'PROMPT' -S YORN -T TERMTYPE \
.    -d DEVICE -l TTYID -s /usr/bin/login`"

    Note the assorted quotes; Bourne shell (sh) and Korn (ksh) users
    leave off the second backslash!

    In the above:

    PMTAG is the port monitor name you made with "sacadm", e.g. "zsmon".

    SVCTAG is the service tag, which can be the name of the port, e.g.,
..    "ttya" or "tty21".

    PROMPT is the prompt you want to print, e.g. "login: ".

    YORN is "y" to turn software carrier on (you want this for directly
    connected terminals" and "n" to leave it off (you want this
    for modems).

    TERMTYPE is the value you want in $TERM.

    DEVICE is the name of the device, e.g. "/dev/term/a" or "/dev/term/21".

    TTYID is the line you want from /etc/ttydefs that sets the baud rate
.    and stuff.  I suggest you use one of the "contty" ones for
.    directly connected terminals.

    5. To disable ("turn off") a terminal, run

.    pmadm -d -p PMTAG -s SVCTAG

    To enable ("turn on") a terminal, run

.    pmadm -e -p PMTAG -s SVCTAG

    Ports are enabled by default when you "create" them as above.

    For more details, see:
.    Celeste's Tutorial on Solaris 2.x Modems & Terminals
.    <http://www.stokely.com/stokely>

3.21) How do I get the screen to blank when nobody's using it?

    Under 4.1.x you invoke screenblank in /etc/rc.local, but there's no
    screenblank in Solaris 2.x.  Sun recommends that you
    have everybody put `xset s on' in their .xinitrc, but this
    may be hard to police, and in any event it won't work when nobody is
    logged in.  The simplest workaround is to copy /usr/bin/screenblank
    from 4.1.x and run it in binary compatibility mode.  See ``What
    happened to /etc/rc and /etc/rc.local?'' for how to invoke it.

    Another possibility is to use xdm or dtlogin.  That way the X server
    will continue to run and the screen will be blanked by it.

    The 4.1.x screenblank didn't work for us. We use Jef Poskanzer's
.    <http://www.acme.com/software/screenblank/>
    freeware screenblank.

    Because of a bug in Solaris 2.3, you'll may to
    specify -DHAVE_POLL=0 when compiling this version.

    Solaris 2.4 comes with power management software for those systems
    with a soft-switchable power supply.  That may suit your needs
    better than screenblank.  In Solaris 2.5 the software can remove
    the sync signal from your monitor causing newer monitors to go
    in energy saving standby mode.  The Solaris 2.4 version had problems
    reenabling the monitor or graphics card.

    The power-management software is on the SMCC Updates CD [2.4 2.5]

    The power-management software can be used to switch off just the
    screen, by putting the following in the power.conf file:

    # Name                  Threshold(s)     Logical Dependent(s)
    /dev/kbd                600
    /dev/mouse              600
    /dev/fb                 0 0             /dev/kbd /dev/mouse

    Make sure you mark the "autoshutdown" line with "noshutdown"
    if you want keep your machine running.

    The /usr/openwin/bin/dtpower utility can change these settings for
    you.  (Solaris 2.5)

3.22) And what about screendump, screenload and clear_colormap?

    You can FTP Jef's screenload, screendump, etc., if you need that
    functionality, and for free you get a pixrect (clone) library.
    Get one of these:
.    http://www.acme.com/software/raster-pixrect/
.    ee.lbl.gov:/raster-pixrect_30dec93.tar.Z

    The 4.1.x versions of these programs will not run under
    Solaris 2.2 or later.  The pixrect BCP library is no
    longer supported.

3.23) Where did etherfind go?

    There is a replacement for etherfind, but it has changed name;
    in fact it's a whole new program. It IS better. To find it,
    though, you would have to realize that network snooping is not
    really Ethernet-specific.  To end the suspense :-), here it is:

    % man -k snoop
    snoop   snoop (1m)      - capture network packets and inspect them
    %

    It works differently - it has an immediate mode, a
    capture-to-disk mode, and a playback-from-disk mode.  Read the
    man page for details.

    The capture file format is described in RFC 1761.

|*3.24) Can I run SunOS4.1.x on my SPARC Classic, LX, SS5, SS4, SS20, Voyager,
    SS1000, SC2000, CS6400, Ultra?

    The Classic, LX and the single processor models of the SS20
    are still supported under some version of SunOS 4.1.x.
    A lot of people wanted these machines but only if they ran
    SunOS 4.1.x.  When the Classic/LX came out, clone manufacturers
    were able to provide SunOS 4.1.x with it, Sun came out with
    SunOS 4.1.3C some time later.

    The Classic, LX, SS4, SS5 and SS20 are supported in the most recent
    Solaris 1.x release, SunOS 4.1.4 (Solaris 1.1.2).  The Classic and
    LX are supported since 4.1.3C (release for LX & Classic only), the
    SS20/SS5 since release 4.1.3_U1 rev B (Solaris 1.1.1B).  The SS4
    and SS20 with HyperSPARC since 4.1.4.  Note that none of these OS
    versions support SuperSPARC MP or any of the new graphics hardware
    (ZX, TZX, SX, S24).  The TCX adapter is only supported as a
    cgthree, and SunOS 4.x doesn't use all its acceleration features.

    The Voyager is not supported under SunOS 4.1.x, too many new device
    drivers have been added plus the suspend resume feature.

    The XDbus machines SS1000/SC2000 are also not supported under
    SunOS 4.1.x.  Support for their kernel architecture and XDBus is
    missing in 4.x.

    The UltraSPARC based machines are not supported under SunOS 4.1.x.
    The new supervisor mode instructions, the new MMU, buses and devices
    are not supported under 4.1.x.

    Sun acquired the Business Systems Division of Cray Research and now
    supports the Cray CS6400, a 64 SuperSPARC machine that runs a modified
    version of Solaris 2.x, known as "Cray Solaris".

|   The largest Solaris 2.x machine you can currently buy from Sun is the
    Ultra-Enterprise 10000, a machine that supports upto 64 UltraSPARC
.    <http://www.sun.com/datacenter/>
    cpus, 64 I/O channels and 64 GB of memory at the same time.

|   Fujitsu sells an even larger machine, the AP-3000,
|.    <http://www.fujitsu.co.jp/hypertext/Products/Info_process/hpc/ap3000-e/index.html>
|   a system with upto 2048 UltraSPARC cpus @300MHz.

3.25) The "find" program complains that my root directory doesn't exist?

    Yes! Actually, messages like

    find : cannot open /: No such file or directory.

    are due to a bug in the tree walking function (nftw(3)).

    Fixed in 2.4 and in the 2.3 kernel jumbo patch 101318 (-41 or later)


3.26) I'm having troubles with high-speed input on the Sparc serial
    ports.  What should I do?

    Try using UUCP.  The Solaris 2.x sparc serial driver has
    trouble receiving data at or above 9600 bps.  Symptoms include
    sluggish response, `NOTICE: zs0: silo overflow' console
    messages, sending spurious control-Gs to the serial port, and
    applications that cannot be killed even with `kill -9'.  This
    problem surfaces in many applications, including Kermit and
    tip.  UUCP seems immune, though, because its protocol throttles
    input sufficiently.

    People have reported success in later releases of Solaris (2.3+).

    Solaris 2.5 supports much higher baudrates and hardware flowcontrol
    in two directions. The latter is also available as a patch for
    2.3 (102028) and 2.4 (102845, note that this patch conflicts with
    patch 102062-08, which should be installed first if at all).
    The zs device can be set to 38400bps in 2.4 and earlier
    and 76800 in 2.5 and later.

|3.27) How do I make ksh or csh be the login shell for root?

    Root's shell is /sbin/sh, which is statically linked.
    Don't just insert a 'c' before "sh" as previously, as that would
    look for /sbin/csh, which doesn't exist.  Don't just change it to
    /bin/csh, since that's really /usr/bin/csh, which is dynamically
    linked, because:
.    1) /usr may not be mounted initially, and then
.       you're in deep (the shared libraries are in /usr!), and
.    2) There is code in the startup scripts that assumes that
.       everything critical is in /etc/lib, not /usr/lib.
    Approach with caution!

    Whenever you change root's shell, make sure you do it using
    vipw or "passwd -e".  Both programs will check for a valid
    (in the sense of /etc/shells) file.

    Safer bet - have an alternate root account, like "rootcsh",
    with uid 0, and /bin/csh as its shell. Put it after root's entry in
    the passwd file.  Only drawback: you now have to remember to
    change all of root's passwords at the same time.

    Third bet - in root's .profile, check if /usr is mounted and, if so,
    exec /bin/ksh or whatever.

    An even better bet - leave root's shell alone, and use the
    sudo command for doing things as root.
.    <ftp://ftp.cs.colorado.edu/pub/sysadmin/sudo>

3.28) What is this message: "automount: No network locking on host,
    contact administrator to install server change."?

    The other machine (an NFS server) is running 4.1.x and needs a
    patch from Sun to update its network lock daemon (lockd). If
    you don't install the patch on the server, file locking will
    not work on files mounted from "thathost". The lockd jumbo patch
    fixes a bunch of other lock manager problems, so it may be a
    Good Thing To Get; however, it may also cause the machine on
    which the patch is installed to have trouble talking to servers
    with no patch or older patches, so Be Warned.

    The lockd patches are: 100988 (4.1.3), 101817 (4.1-4.1.2)
    101784 (4.1.3_U1), 102264 (4.1.4) and 100518 (for Online: Disksuite).

    Make sure you install the latest version of those patches.

|3.29) I have all kinds of problems with SCSI disks under Solaris 2.x
    They worked fine under SunOS 4.x.

    Append this line to /etc/system and reboot:

.set scsi_options & ~0x80

    This turns off Tagged Command Queuing, a SCSI feature that is
    improperly implemented in many older drives.

    NOTE: this will seriously degrade performance on disks that do
    properly support tagged command queuing.  Setting the SCSI options
    per broken target is therefor the preferred solution.

    In Solaris 2.4 and later you can set those options per SCSI
    bus.  See isp(7) and esp(7).

    For some disks, all you need to do is decrease the maximum number of
    queued commands:

.forceload: drv/esp
.set sd:sd_max_throttle=10

    In later Solaris releases you can specify scsi_options per (broken)
    target or per SCSI bus.  See esp(7d), isp(7d), from which this example
    /kernel/drv/esp.conf file is derived:

         name="esp" parent="/iommu@f,e0000000/sbus@f,e0001000/espdma@f,400000"
. reg=0xf,0x800000,0x40
. target1-scsi-options=0x58
. scsi-options=0x178;


3.30) How do I make Solaris2 use my old ADAPTEC ACB-4000 and
    Emulex MD-21 disk controllers?

    As with any hardware addition, first try the obvious (boot -r
    after installing and power-cycling everything).

    The adaptec is no longer supported; man -s7 sd no longer even
    lists it!  So I guess they go over the cliff. Either that, or
    take the drives out and put them on a PC, where ST506 MFM
    drives are still supported.

    The MD21 should work, though some people report that SCSI
    doesn't work in 4/260 boxes (bug-id #1118752), but that's
    fixed in 2.3 and later.

3.31) Should I wait installing 2.5 until there are enough patches?

    Several things have been done differently during the development
    of Solaris 2.5.  More internal users run versions of Solaris 2.5
    no more than one or two weeks old.  A number of large customers
    ran 2.5 beta releases on production systems, in exchange for
    virtually unlimited engineering support for those machine.

    Coupled with some other development policies this has resulted in
    a release of very high quality that doesn't come with 36 patches
    on the first release CD, instead with just 5 for OpenWindows
    and a number for unbundled products.

    Solaris 2.5 should run most everything without requiring patches.

3.32) Why are there so many patches for Solaris 2.x?

    Solaris 2.x releases are essentially frozen several months before
    their general release date.  During the early access/beta test
    period bugs are found both in the beta and in the previous
    release.  That's why the moment a new release comes out a
    number of patches is ready. Some of those are on the Solaris
    2.x CD.  Others were released almost at the same time as 2.x,
    or even before 2.x becomes generally available.

    Some bugs are found in the previous release that can't be fixed
    in the time for the next release.  And bugs get added to new
    code.

3.33) What are the ``mandatory'' patches I keep hearing about?

    The mandatory patches weren't mandatory, so they've been relabeled.
    They're now called ``recommended'' patches.

    The recommended patches are those patches Sun recommends for
    trouble free system operation.  With those patches installed,
    your chances on trouble free operation are higher.  That doesn't
    mean you will run into trouble without them.

    These recommended patches can be anonymously ftp'ed from
    official Sun ftp sites.

3.34) Which patches should I apply?

    "If it ain't broke, don't fix it."  In general you should only
    apply patches for security related problems.  For each and every
    other patch you must consider two things: have I encountered this
    bug or am I very likely to encounter this bug in the near future.
    If neither is true, it is often best not to apply the patch.
    If you have a working system, why patch it?  Patches do occasionally
    introduce new bugs and not applying patches is the best way to
    avoid those new bugs.

    You should, however, install all patches that come with the
    Solaris 2.x CDs.  Those patches have been tested together and
    supplement the base OS to the supported level.  Some systems won't
    even boot if those patches aren't installed first.

3.35) Where do I get patches from?

    Sites not sponsored by Sun, accessible for all:

    ugle.unit.no:/pub/unix/sun-fixes
    ftp.luth.se:/pub/unix/sun/all_patches

    SunSites (carry recommended and security patches):

    sunsite.unc.edu:/pub/sun-info/sun-patches
    sunsite.sut.ac.jp:/pub/sun-info/sun-us/sun-patches
    sunsite.doc.ic.ac.uk:/sun/sunsite-sun-info/sun-patches

    Sunsolve:

    sunsolve1.sun.com:/pub/patches
    http://sunsolve1.sun.com/

    These are Sun's own sites, they has the recommended patches up for
    anonymous ftp, packaged as one huge 2.x_Recommended.tar.Z file
    and as individual patches.

    Starting with SunSolve CD 2.1.2 ALL Sun patches are shipped
    on the SunSolve CD.

    Contract customers can get all patches by ftp from Sunsolve
    or via e-mail and query one of the online sunsolve-databases
    on the Internet.

3.36) Where can I obtain Solaris 2/x86 driver updates?


    The Solaris x86 driver updates can be obtained by HTTP from:

.http://access1.sun.com/drivers/driverMain.html
.http://sunsite.unc.edu/pub/sun-info/solaris-x86/sunsoft-drivers

    The Solaris x86 driver updates can be obtained by anonymous ftp from:

.ftp.uu.net:/vendor/sun/solaris/
.sunsite.unc.edu:/pub/sun-info/solaris-x86/sunsoft-drivers

3.37) Why does installing patches take so much space in /var/sadm?

    All the files that are replaced by a patch are stored under
    /var/sadm/patch/<patch-id>/save so the patch can be safely
    backed out.  Newer patches will save the old files
    under /var/sadm/pkg/<pkg>/save/<patch-id>/undo.Z, for each package
    patches.

    You can remove the <patchdir>/save directory provided you also
    remove the <patchdir>/.oldfilessaved file.  Newer patches will not
    install a .oldfilessaved file.

    Alternatively, you can install a patch w/o saving the old
    files by using the "-d" flag to installpatch.

3.38) Do I need to back out previous versions of a patch?

    No, unless otherwise stated in the patch README.
    If the previous patch installation saved the old
    files, you may want to reclaim that space.

    Patches can be backed out with:

.    /var/sadm/patch/<patch-id>/backoutpatch <patch-id>

    Backoutpatch can take an awful long time, especially when the
    patch contained a lot of files.  This is fixed in later versions
    of backoutpatch.

3.39) How can I have more than 48 pseudo-ttys?

    Edit /etc/system and add the following line:

.* System V pseudo terminals

.set pt_cnt = <num>

    Halt the system and boot -r.

    You can essentially have as many as you like, but you'll probably
    run into some other limit somewhere.  More than 3000 are supported.

    In the unlikely event that you run out of BSD-style ptys,
    you can increase them as well.  The maximum there is probably
    256 as all programs using BSD ptys need to hardcode all the
    possible device names and 256 was the maximum previously
    found in SunOS 4.  BSD ttys are awkward to use and all
    programs I found support SYSV ptys without trouble.

.* You don't need this.  Increasing this value too much usually
.* just wastes memory.

.set npty = <num>

    Halt the system and boot -r.

3.40) How can I have normal users chown their files?

    Add the following to /etc/system:

.set rstchown  = 0

    This will defeat the quota system and may compromise the
    security of your system.


3.41) How can I get ps to print %MEM and %CPU?

    Prior to Solaris 2.4, the OS didn't do the bookkeeping
    necessary to obtain these values.  In Solaris 2.4 the code
    was added to kernel and /usr/ucb/ps can now show these values.

    Under Solaris 2.3 and earlier your only recourse is using
    the public domain utility top (See 2.3).

3.42) How can I get the DOS and Unix clock to agree on Solaris/x86?

    After installation, run the command /usr/sbin/rtc -z $TZ,
    where $TZ is your timezone.  The default root crontab runs
    /usr/sbin/rtc -c once every day.

    That way your clock will give the proper time whether you boot
    Solaris or DOS/Windows.

3.43) How can I increase the number of file descriptors per process?

    In 2.3 in earlier this requires poking the kernel.
    In Solaris 2.4+, this can be accomplished by adding the
    following lines to /etc/system:

.* set hard limit on file descriptors
.set rlim_fd_max = 4096
.* set soft limit on file descriptors
.set rlim_fd_cur = 1024

    Raising the soft limit past 256 may confuse certain applications,
    especially BCP applications.  Raising the limit past 1024 may
    confuse applications that use select().

    Programs using stdio or even library calls that use stdio may break
    when they have more than 256 files open as that is the stdio limit.
    Programs using many filedescriptors should try and reserve a number
    of low numbered file descriptors for use by stdio.

3.44) Can I install both SunOS and Solaris on the same machine,
    and choose between them at boot time?

    Yes, that is possible.  All partitions other than the system
    partitions (typically /, /usr, /var and /opt) can be shared by the
    two OSes.  All partitions, including the system partitions, can be
    mounted and accessed by either OS.

    The easiest way to set this up is to do separate suninstalls on two
    different disks.  Then just choose the appropriate disk at boot
    time with the PROM's "boot" command.

    Setting up both OSes on one disk is a little harder, but not much.
    You need to partition the disk to allow for both OSes.  Almost any
    partition layout is possible, but one common setup might be:

     a: / for Solaris 2
     b: swap (shared)
     c: The usual (whole disk)
     d: / for Solaris 1
     e: /usr for Solaris 1
     g: /usr for Solaris 2

    Again, it's most reliable to use suninstall to do the installations.
    If for some reason you choose not to use suninstall, make sure you run
    installboot for both bootable partitions.

    With this setup, you choose between the two OSes in the PROM's "boot"
    command as follows:

    To boot Solaris 2:.boot
    To boot Solaris 1:.boot disk:d

    NOTE: In boot PROM versions <= 2.5, the "disk:d" syntax is not supported,
    and the PROM cannot boot from root partitions that begin or end beyond 1GB.

3.45) How do I disable banner pages under Solaris?

    As root, go to directory /etc/lp/interfaces.  Edit the file that
    corresponds to the printer name.  Change the line that reads
    'nobanner="no"' to 'nobanner="yes"'.

3.46) How do I change my hostname?

    The supported way to change your hostname is:

.# /usr/sbin/sys-unconfig

    The system will halt and on subsequent boot will ask for its name
    and other networking parameters again.

    You may wish to save a copy of /etc/nsswitch.conf beforehand as
    that file is overwritten by the configuration process.

    Note that sys-unconfig is not supported on diskless or dataless
    workstations.  On those, you'll need to edit files by hand.  See the
    sys-unconfig(1M) for a list of the files that need changing.

3.47) Can I run multiple terminals on the console of Solaris x86
   like those supported on Interactive Unix and SCO?

    Yes.  In Solaris x86 2.1, these worked 'out of the box'.

    In Solaris x86 2.4, they are no longer configured during the
    installation, but they still work if configured afterwards by hand.
    Sun apparently disabled them in this way because they are no longer
    officially supported, but fortunately, they did not actually remove
    them from the kernel, so you can configure them back in yourself as
    follows.

    First verify the device's major number with grep:

.# grep -i chanmux /etc/name_to_major
.chanmux <num>


    Add the /dev entries, substituting whatever you found with grep
    for <number>:

.mknod /dev/vt01 c <number> 1
.mknod /dev/vt02 c <number> 2
.etc...

    add the following to /etc/inittab (after the co entry):

.v1:234:respawn:/usr/lib/saf/ttymon -g -h -p "VT1 Login: " -T AT386 -d /dev/vt01 -l console
.v2:234:respawn:/usr/lib/saf/ttymon -g -h -p "VT2 Login: " -T AT386 -d /dev/vt02 -l console
.etc...

    To get init to reread inittab, either reboot, or issue the command:

./usr/sbin/init q

    Now,
    Alt-PrintScreen F1 switches to VT1,
    Alt-PrintScreen F2 switches to VT2,
    etc,
    Alt-PrintScreen P  switches to previous screen in cyclic sequence,
    Alt-PrintScreen N  switches to next     screen in cyclic sequence.
    Alt-PrintScreen H  switches to console  screen (and not
...   Alt-PrintScreen F8 as on Interactive Unix)


3.48) How can I prevent daemons from creating mode 666 files?

    By default, all daemons inherit the umask 0 from init.
    This is most problematic for a service like ftp, which in a
    standard configuration leaves all uploaded files with mode 666.

    To get daemons to use another umask execute the following
    commands in /bin/sh and reboot:

    umask 022  # make sure umask.sh gets created with the proper mode
    echo "umask 022" > /etc/init.d/umask.sh
    for d in /etc/rc?.d
    do
.ln /etc/init.d/umask.sh $d/S00umask.sh
    done

    Note: the trailing ".sh" of the scriptname is important, if
    you don't specify it, the script will will be executed in a
    sub-shell, not in the main shell that executes all other scripts.

3.49) How do I change the terminal type for /dev/console?

    Change the "-T sun" in the following line in /etc/inittab to
    "-T <termtype>":

.co:234:respawn:/usr/lib/saf/ttymon -g -h \
..-p "`uname -n` console login: " -T sun \
..-d /dev/console -l console -m ldterm,ttcompat

    (Line broken for readability)

3.50) If I login over the network, my terminal type is set to "sun"/"AT386"
    How can I change that?  In SunOS 4.x the type would have been "network"

    If no terminal type is specified in the network (telnet/rlogin)
    protocol, the standard startup scripts (/etc/profile, /etc/.login)
    will set the terminal type to the default console type (sun for
    SPARCs, AT386 for x86).

    To get the SunOS 4.x. behaviour back, all you need to do is set the
    type to "network", if not previously set.

3.51) How can I change the SYSV IPC parameters?

    The following parameters can be used to change the number of
    semaphores, the amount of shared memory and the number of IPC
    messages.  They're set in /etc/system, as usual.

    set semsys:seminfo_semusz = <value>
    set semsys:seminfo_semopm = <value>
    set semsys:seminfo_semume = <value>
    set semsys:seminfo_semaem = <value>
    set semsys:seminfo_semmap = <value>
    set semsys:seminfo_semvmx = <value>
    set semsys:seminfo_semmsl = <value>
    set semsys:seminfo_semmni = <value>
    set semsys:seminfo_semmns = <value>
    set semsys:seminfo_semmnu = <value>

    set shmsys:shminfo_shmmin = <value>
    set shmsys:shminfo_shmseg = <value>
    set shmsys:shminfo_shmmax = <value>
    set shmsys:shminfo_shmmni = <value>

    set msgsys:msginfo_msgseg = <value>
    set msgsys:msginfo_msgssz = <value>
    set msgsys:msginfo_msgtql = <value>
    set msgsys:msginfo_msgmap = <value>
    set msgsys:msginfo_msgmax = <value>
    set msgsys:msginfo_msgmnb = <value>
    set msgsys:msginfo_msgmni = <value>

|3.52) How do I enable/disable dtlogin?

    Whether dtlogin is started or not is settable with /usr/dt/bin/dtconfig
    As dtlogin itself explain when invoked without arguments:

.    /usr/dt/bin/dtconfig -d        (disable auto-start) 
.    /usr/dt/bin/dtconfig -e        (enable auto-start) 
.    /usr/dt/bin/dtconfig -kill     (kill dtlogin) 
.    /usr/dt/bin/dtconfig -reset    (reset dtlogin) 
.    /usr/dt/bin/dtconfig -p        (printer action update) 
.    /usr/dt/bin/dtconfig -inetd    (inetd.conf /usr/dt daemons) 
.    /usr/dt/bin/dtconfig -inetd.ow (inetd.conf /usr/openwin daemons) 

4. NETWORKING

4.1) How do I use DNS w/o using NIS or NIS+?

    Under SunOS 4.1 it was next to impossible to run DNS name resolution
    without either a kludge fix or the NIS (V2 I guess). Under Solaris
    2.1 it is incredibly simple, but you must ignore what the manual
    (SunOS 5.1 Administering NIS+ and DNS) says (the manual is fixed
    in Solaris 2.2). All that is required to make a non-NIS host
    use the DNS for name resolution is to change the host: line in
    the /etc/nsswitch.conf file to the following:

    hosts:  files dns

    (i.e., when looking for hosts, look in /etc/hosts first, if not
    found there, try DNS, if still not found then give up) and set
    up a correct version of /etc/resolv.conf to tell the resolver
    routines (like gethostbyname) how to contact the DNS
    nameserver. You must have the names of machines which are
    somehow contacted during boot in the files in /etc and files
    must appear first in the hosts: line, otherwise the machine
    will hang during boot (at least ours did). Make sure that
    /etc/netconfig is as it was shipped.  (In Solaris 2.3 and earlier,
    it will use "switch.so,tcpip.so" for ip, in Solaris 2.4 it
    just uses "-")

4.2) Speaking of nsswitch.conf, what is it?

    An idea whose time has come (it came to Ultrix a few years
    ago).  You can control which of the "resolver" services are
    read from NIS (formerly YP), which from NIS+, which from the
    files in /etc, and which are from DNS (but only "hosts" can
    come from DNS).

    A common example would be:

    hosts: nis files

    which means ask NIS for host info and, if it's not found, try
    the local machine's host table as a fallback.

    Advice: if you're not using NIS or DNS, SunInstall probably put
    the right version in. If you are, ensure that hosts and passwd
    come from the network. However, many of the other services
    seldom if ever change.  When was that last time *you*
    added a line in /etc/protocols? If your workstation has a local
    disk, it may be better to have programs on your machine look up
    these services locally, so use "files".

    Terminology: Sun worried over the term "resolver", which
    technically means any "get info" routine (getpwent(3),
    gethostbyname(3), etc), but is also specifically attached to
    the DNS resolver.  Therefore they used the term "source" to
    mean the things after the colon (files/DNS/NIS/NIS+) and
    "database" to mean the thing before the colon
    (passwd/group/hosts/services/netgroup etc).

    A complete discussion can be found in nsswitch.conf(4).

4.3) What does [NOTFOUND=return] in nsswitch.conf mean?

    Type "man nsswitch.conf" for more info.  There is too much
    detail to summarize here.  Briefly, [NOTFOUND=return] means
    that the name service whose entry it *follows* should be
    considered authoritative (so that if it's up and it says such a
    name doesn't exist, believe it and return instead of continuing
    to hunt for an answer).

4.4) Can I run a nis/yp server under Solaris 2.x?

    Yes, you need the Solaris network transition kit available from
    Sun.  A number of those have been made available over time:

    1) NSkit 1.0.  A version of SunOS 4.x NIS executables made to
    work on Solaris 2.x.  Fully included in patch 101363-08.
    2) NSkit 1.1.  Native, available from OPcom, but never left beta
    stage.  Didn't do DNS lookups well (the entire server hangs until
    a DNS request is answered).
    3) NSkit 1.2.  Native.  Freely available from the Solaris 2.x
    migration initiative home page.  Supports multi-homed hosts,
    async DNS lookups and shadow password maps.  Also shipped with
    the 2.5 server kit.

    NSkit 1.2 is available for SPARC and x86.

4.5) Can I run NIS+ under Solaris 1 (SunOS 4.1.x)

    Sort of, with the NIS+ server implementation for Solaris 1.x
    that comes on the Solaris 2.x CD.  This is a server side only
    implementation and requires NIS+ to run in YP compatibility
    mode.

4.6) With NIS+ how do I find out which machine a client is bound to?

    NIS+ clients do not hard bind to nis+ servers in the same
    way that NIS clients bind to NIS servers. The clients have a
    list of NIS+ servers within the cold-start file. When they need
    to do a lookup they do a type of broadcast called a "manycast"
    and talk to the first server that responds. This way they can
    be sure to use the lightest loaded server for the request.

4.7) Ypcat doesn't work on the netgroup table on a NIS+ server, why?

    Yes, that is a known problem.  The only operations allowed from
    a NIS client side on the netgroup table are the ypmatches, but
    not ypcat (i.e. no support for yp_first(), yp_next() or
    yp_all() calls).  The netgroup table is kind of unique in
    this.  The reason for this is that the netgroup table format
    changed quite significantly in NIS+ and the NIS+ server would
    take a big performance hit in converting the netgroups table to
    YP (key-value) format.

4.8) Why is rpc.nisd such a memory pig according to ps?

    The good news is that it's not memory OR swap space you're
    being shown by 'ps'.  Instead it's showing you the process
    ADDRESS space which includes 256 MB of address space reserved
    for the NIS+ transaction log.  Given the cost of moving things
    around in memory and the fact that we have 4 GB of address
    space to play with it, this is a good idea.  You've just got to
    stop thinking small.  THINK BIG.  It's only 1/16th of the total
    process address space being used.  And if you ever exceed the
    256 MB size of the transaction log you're doing something VERY
    wrong.

4.9) How do I tell my NIS+ server to service DNS requests from
    4.x clients?

    Start rpc.nisd with the -B switch.  This can be done editing
    the server's /etc/init.d/rpc file and change 'EMULYP="-Y"' to

.    EMULYP="-Y -B"

4.10) How can I have multiple addresses per interface?

    Solaris 2.x provides a feature in ifconfig that allows having more
    than one IP address per interfaces.  Undocumented but existing
    prior to 2.5, documented in 2.5 and later.

    Syntax:

.ifconfig IF:N ip-address up

    where "IF" is an interface (e.g., le0) and N is a number between 1 and
    <MAX>.  Removing the pseudo interface and associated address is done
    with "ifconfig IF:N 0.0.0.0 down".

    As with physical interfaces, all you need to do is make the
    appropriate /etc/hostname.IF:X file.

    The maximum number of virtual interfaces, <MAX> above, is 255 in
    Solaris releases prior to 2.6.  Solaris 2.6 and Solaris 2.5.1 with
    the Solaris Internet Server Supplement (SISS) allow you to set
    this value with ndd, upto a hard maximum of 8192.

    /usr/sbin/ndd -set /dev/ip ip_addrs_per_if 4000

    There's no limit inspired by the code; so if you bring out adb you
    can increase the maximum even further.

4.11) Solaris 2.x supports filesystem sizes up to 1TB.  Will this
    give interoperability problems with NFS?

    No, you can share those filesystems with SunOS 4.x and other machines
    just fine.  The NFS protocol rarely transmits the size of the
    underlying filesystems.  The only programs on SunOS 4 clients that
    may give trouble are du and df, but normal filesystem use is just
    fine.

|4.12) Where can I get an SNMP agent for Solaris?

    There are several agents available, including one from Sun.

    ftp.ece.ucdavis.edu:/pub/snmp

    Solstice Enterprise Agents, hit the "software download" icon
|.    <http://www.sun.com/software/solstice/products/ent.agents>

    Sun SNMP agents <ftp://zippy.telcom.arizona.edu/pub/snm/patches/snmpd2.2.3/>

    Solaris 2.6 ships with an SNMP agent.

|*4.13) How can I use full-duplex ethernet?

    Sun's hme fast ethernet adaptors support full-duplex ethernet; it isn't
    enabled by default because when first shipped the full-duplex standard
    hadn't materialized yet.

    There are several ways of changing the default settings and force
    full-duplex mode; you may need to alter your switch settings as well.

    Setting through /etc/system

..set hme:hme_adv_autoneg_cap=0
..set hme:hme_adv_100hdx_cap=0
..set hme:hme_adv_100fdx_cap=1

    Setting with ndd
..ndd -set /dev/hme adv_autoneg_cap 0
..ndd -set /dev/hme adv_100hdx_cap 0
..ndd -set /dev/hme adv_100fdx_cap 1

    In case you have multiple instances, you need to select the specific
    hme instance first, e.g., use the following to select hme1:

..ndd -set /dev/hme instance 1

|   If you need to query the device, you can interrogate various variables
|   such as ``link_status'', ``link_speed'', etc.

|+4.14) Where can I get BOOTP/DHCP for Solaris?

|   Solaris 2.6 ships with BOOTP/DHCP support.

|   Software for Solaris 2.5/2.5.1 is available from Sun's website.
|.    <http://www.sun.com/javastation/jcdev/software.html>

|   Click on the license agreement form (after reading it) and download
|   the SUNWdhcsr and SUNWdhcsu packages.  You'll also need to
|   install SUNWfns, but that's a standard part of Solaris 2.5
|   provided only for completeness.


5. TROUBLE SHOOTING

5.1) The Solaris 2.x application XX fails with a mysterious error condition.

    Try truss(1).  truss -f -o file cmd args ...
    will put a trace of all system calls in "file".
    This often helps as a first step in diagnosing many failure modes,
    such as insufficient permissions on certain files etc..

5.2) In Solaris 2.5 nm is slow or dumps core.

    A bug introduced in the 2.5 locale libraries make strcoll()
    return bogus values when confronted with empty strings.
    This bogus empty string comparison makes that strcoll no longer
    defines a strict order on strings, that confuses the hell out
    of qsort which promptly crashes.

    Workaround: set LC_COLLATE to "C"

    (Note that xview applications will usually reset LC_COLLATE to
    LC_ALL, so in cmdtool/shelltool windows, LC_COLLATE needs to be set
    again.)

5.3) Why can't I run Answerbook on a standalone machine?

    This is a bug in OpenWindows.  Using xhost + or starting
    "openwin -noauth" works around this problem.  This is
    only recommended for stand-alone machines with no dial-in
    users.  [ S 2.3 ]

5.4) Why can't I display Answerbook remotely?

    Displaying answerbook requires support for the DPS extension in the
    X server.  The DPS extension is supported by most common Unix
    workstations, but not by most PC/X offerings and is often an extra
    cost item for X terminals.

    A number of people have reported success using ghostview as a
    replacement for the answerbook viewer, but this has the unfortunate
    side effect of not supporting the hypertext links in the documents.

    A better solution is to install a client side Display PostScript
    extension.

    Adobe has defined such a client side extension and call it
    DPS-NX. Bluestone sells a version.
.    <http://www.bluestone.com/>

5.5) Why can't I run filemgr, I get ``mknod: permission denied''?

    This is a symptom of a bug in filemgr in Solaris 2.3.
    Either apply patch #101514 or run the following commands
    at system start-up:
.     mkdir /tmp/.removable
.     chmod a+rwxt /tmp/.removable

5.6) Why do I get isinf undefined when linking with libdps on Solaris 2.3?

    That's a bug in libdps (fixed in 2.4).  Sun compiles and links its
    software with its own compilers.  The isinf() function is shipped
    with the SunPRO compilers, but not defined in any Solaris 2.3
    library.

    A workaround exists, and consists of adding the following to
    your program:

    #include <ieeefp.h>

    int isinf(double x) { return !finite(x) && x==x; }

5.7) I can't get PPP to work between Solaris 2.3 and other platforms.

    The PPP shipped with Solaris 2.3 doesn't interoperate with
    other PPP implementations.  Patch #101425 fixes this.

5.8) Using compat mode for passwd doesn't work in 2.3?

    You need patch #101448.

5.9) Why do I get __builtin_va_alist or __builtin_va_arg_incr undefined?

    You're using gcc without properly installing the gcc fixed
    include files.  Or you ran fixincludes after installing gcc
    w/o moving the gcc supplied varargs.h and stdarg.h files
    out of the way and moving them back again later.  This often
    happens when people install gcc from a binary distribution.
    If there's a tmp directory in gcc's include directory, fixincludes
    didn't complete.  You should have run "just-fixinc" instead.

    Another possible cause is that you're using ``gcc -I/usr/include.''

5.10) My machine hangs during the boot process.  It seems related to ps.

    When the system boots, the first invocation of ps will try to
    recreate /tmp/ps_data.  To this end ps scans the /dev tree.
    Under some circumstances, a loop exists in /dev and ps will
    run forever.  Most of the time this loop is caused by the symbolic
    link /dev/bd.off.  While this link usually points to /dev/term/b,
    it sometimes get truncated and points to /dev instead.

    Fix: rm -f /dev/bd.off; ln -s /dev/term/b /dev/bd.off

    Use truss(1) to determine whether this is real the cause of your
    problem.

5.11) Syslogd doesn't seem to log anything.

    Make sure you have /usr/ccs/bin/m4 installed.  It's in
    package SUNWbtool (m4 is included in SUNWcsu in 2.4 and later).

    Other causes are bugs in Solaris 2.3 and various revisions of
    patches.  E.g., syslogd is broken in all 101318 patches
    between level -42 and -50.  It works again in 101318-54.

    For 2.4, you may need patch 102534-xx and/or 102697-xx.

5.12) I get ``Invalid client credential'' when mounting filesystem on
    Solaris client from non-Sun fileserver.

    Some vendors still ship a version of RPC/NFS that allows at
    most 8 groups in the client credentials.  Root on Solaris is by
    default in 10 groups.  As a result, the Solaris 2.x mount
    command will send AUTH_UNIX credentials that are too big to
    cope with for the remote mount daemon resulting in the ``Invalid
    client credential'' error.

    Workaround: put root and all your users in 8 or less groups.
    NOTE: You must logout and login again for changes in the number
    of groups to take effect. (or exit root's shell and re-su)

5.13) After upgrade to 2.4, ls on NFS mounted directories hangs.

    Starting with Solaris 2.4, a kernel workaround to limit
    NFS readdir requests to 1024 bytes was disabled by default.
    This breaks interoperability with buggy old NFS implementations
    (such as SunOS 3.2, Ultrix and NeXT)

    There are two workarounds.  The first one works and is:

.mount all filesystems from such servers with rsize=1024.

    The second one, which requires a patch for bugid #1193696
    (101945-29 or later for SPARC, 101946-24 or later for x86)

    Edit /etc/system and add:

.set nfs:nfs_shrinkreaddir = 1

    and reboot.

5.14) After installing patch 101945-xx, I have NFS problems (ksh looping).

    Patch 101945-17 introduced an bug in the NFS client code that makes
    that programs using NFS locking will sometimes go in an
    interruptible read.  (I.e., you can kill the program that hangs)

    Truss will show the program sleeping in read(2) while top
    will show it eating CPU.  The ksh seems to have this quite
    a lot.  There's also a lot of network traffic.

    Fix: install a patch for bug-id #1198278 on your NFS clients.
    (101945-29 or later for SPARC, 101946-24 or later for x86)

    Workaround: mount NFS filesystems with "noac", but this costs
    performance.

5.15) I messed up /etc/system, now I can't boot.

    Boot with -as.  The kernel will ask you all sorts of questions,
    including the name of the system file.  Use the previous
    /etc/system file or specify /dev/null.

5.16) The /etc/path_to_inst file is corrupted, I can't boot.

    Boot with -a and it will ask you to rebuild the path_to_inst file.
    It is possible that you still can't boot after that: if you've
    added/removed controllers/disks, the numbering of the controllers
    may have changed.  You may need to find the new name of /usr and then
    edit /etc/vfstab to change all the disk names.

5.17) TCP/IP connections time out too soon, especially on slow links.

    The tcp/ip abort interval in Solaris 2.x is too short,
    the default value is 2 minutes.  The result is that when an
    ACK isn't received in *2* minutes, the connection is closed.
    This is most often seen by sendmail, which will log

    sendmail: SYSERR: collect: read timeout on connection from ...

    You can fix this by running following command which increases
    the timeout to 8 minutes (unit is millisec), which is the
    Solaris 2.4+ (and patched 2.3) default.

    /usr/sbin/ndd -set /dev/tcp tcp_ip_abort_interval 480000

    This command should be placed in a script rc2.d script. (See 3.16)

    (See 5.19 for another possible cause)

5.18) Sendmail connection to non-Unix hosts don't work.

    With the introduction of sendmail V8 for Solaris 2.x in patch form
    and in Solaris 2.5, a bug in sendmail.cf has suddenly started to
    play up.  The end-of-line character is not defined for the ethernet
    mailer, causing sendmail to send bare newlines in violation of the
    SMTP protocol which requires CR-NL.To fix, find the following line
    in sendmail.cf:

    Mether, P=[TCP], F=msDFMuCX, S=11, R=21, A=TCP $h

    and change it to:

    Mether, P=[TCP], F=msDFMuCX, S=11, R=21, A=TCP $h, E=\r\n

    To be on the safe side, check all lines starting with "M" that contain
    P=[TCP] or P=[IPC].  They all should use "E=\r\n".

    This bug is also fixed in the latest Solaris 2.x sendmail patches.

5.19) Solaris 2.x can't set up any TCP/IP connections to certain hosts.

    Solaris 2.x sets the don't fragment bit on all packets it send
    as part of MTU path discovery.  The Solaris 2.x implementation
    is RFC compliant, but the MTU path discovery protocol will
    fail when there are broken routers in the path.
    Typical symptom is not being able to connect from a
    Solaris 2.x hosts but having no trouble from other hosts or
    being able to start a TCP/IP connection but not move any
    significant amount of data.

    /usr/sbin/ndd -set /dev/ip ip_path_mtu_discovery 0

    (See also 5.17)

5.20) I read 5.19, but I still have connectivity problems.

    Solaris 2.x will still send large packets over such links but
    without the don't fragment bit set.  On a number of occasions, I've
    come across links that don't properly handle such packets.
    They're not fragmented, they're silently dropped instead.

    So if the fix in 5.19 doesn't work you can resort to the
    following drastic measure which negatively impacts network
    performance:

    /usr/sbin/ndd -set /dev/tcp tcp_mss_max 536

    536 is the standard packet size that is guaranteed to work by virtue
    of the fact that most system will communicate outside the local
    net with packets that big.  If the connection then starts to work,
    it's time to find the largest value that works.

    It's also worth mentioning that the "ip_path_mtu_discovery" needs
    to be applied at both sides of a connection to fully work, applied
    at one side it will only affect outgoing large packets.  (I.e.,
    downloads from the site will succeed but uploads from a other
    Solaris 2.x machine w/o the workaround applied may still fail). The
    "tcp_mss_max" workaround need only be applied at one side.

    If you need the "tcp_mss_max" workaround for some sites, there is a
    problem on the link between you and those sites.  Get it fixed.
    Traceroute will tell you where the problem lies.  Try traceroute
    host size, for varying sizes.  If traceroute without a size
    parameter works, but traceroute with a size parameter of 1460 fails
    at some hop, the connection between that hop and the next is
    broken.

5.21) When reading mail on non-Solaris clients of a Solaris mail
    server, or with non-Solaris mail readers, some messages get split
    into multiple messages.

    Solaris 2.x uses the "Content-Length:" header to tell the MUAs
    where messages should be split.  Unfortunately, no-one else
    understands this convention.  Instead, the old convention, ``split
    on "From " lines'' is used most of the time.  Those mail readers
    expect extra lines with "From" to be escaped with ">".

    Workaround: add "E" to the mailerflags of the local mailer.
    Edit /etc/mail/sendmail.cf on your Solaris machines, add E to
    F= on the line that reads:

    Mlocal,       P=/bin/mail, F=flsSDFMmnP, S=10, R=20, A=mail -d $u

    so that it becomes:

    Mlocal,       P=/bin/mail, F=EflsSDFMmnP, S=10, R=20, A=mail -d $u

5.22) Mail/mailx often send reply to wrong user or show wrong sender.

    Mail/mailx use UUCP from line to determine sender, it should use
    the From: header only.  To achieve this you can use the undocumented
    "from" mail variable in your .mailrc:  "set from".

    To make this the default behavior, add "set from" to
    /etc/mail/mailx.rc.

5.23) One of my users can't login (one some machines).

    In the shadow table/file/map there is a field that indicates how
    long an account may be inactive before it is expired.  On login,
    the entry in /var/adm/lastlog, the inactive expire time and the
    current date are compared.  If the system determines that the user
    is expired, he will get "Login incorrect", indiscernible from a
    normal incorrect login.  The fix is to change the user's shadow
    entry.

5.24) My clients with remote /var (/var/adm) partitions won't boot.

    Remote, but unshared filesystems, such as /, /var, /var/adm, etc.
    should be mounted with the llock option.  Solaris 2.x does this
    automatically for remote /, but not for remote /var or /var/adm.
    If you don't specify llock, the system will hang when it tries
    to do stuff to the *[wu]tmp files, early in the boot process.
    And lpsched may fail if it can't lock /var/spool/lp/SCHEDLOCK.

    Workaround: Add the (undocumented) llock option to the mount
    options for /var and/or /var/adm.  (It should be fixed in
    /etc/rcS.d/S70buildmnttab.sh)

5.25) Vacation doesn't work reliably in a mixed Solaris/SunOS environment.

    Vacation was moved from /usr/ucb (in SunOS 4.x) to /usr/bin.
    Unfortunately, the full pathname must be specified in your .forward.

    Workaround: add a link to /usr/ucb/vacation in /usr/bin on SunOS 4
    machines, and add a link to /usr/bin/vacation in /usr/ucb on SunOS 5
    machines.

5.26) I have a lot of <defunct> processes.  How do I get rid of them?

    In general, defunct processes are caused by a parent process not
    reaping its children.  Find out which process is the parent
    process of all those zombies (ps -e).  It's that process that
    has a bug.

    In Solaris 2.3 (and presumably earlier) there is a bug in the
    pseudo tty modules that makes them hang in close.  This causes
    processes to hang forever while exiting.

    Fix: Apply patch 101415-02 (for 2.3).

    In all Solaris 2 releases prior to 2.5 (also fixed in the latest
    2.4 kernel jumbo patch), init (process 1) calls sync() every five
    minutes which can hang init for some considerable time.  This can
    cause a lot of zombies accumulating with process 1 as parent, but
    occurs only in rare circumstances.

5.27) I get /dev/ptmx: No such device when attempting to telnet/rlogin in.

    You need to increase the number of pseudo ttys (See 3.39).

5.28) ld bails out with msync errors.

    You probably use a Cray as fileserver.  It doesn't support all
    NFS operations ld wants to perform.  Install the following patch:
    101409-04: SunOS 5.3: Jumbo linker patch

    [ Solaris 2.3 ]

5.29) su responds with "Sorry" and doesn't prompt for a password.

    Su won't run under a shell compiled under SunOS 4.1.x.
    Recompile your shell (tcsh/bash) under Solaris 2.x.

|*5.30) Why can't I install 2.4 from a non-Sun CD while I could do so with 2.3?

    Several changes were made to the "sd" driver between 2.3 and 2.4.
    In particular, the code that resets the drive to the 512 block size
    is no longer called in the case of a data overrun. Accordingly, it
    is not currently possible to install 2.4 from a local non-Sun
    CDROM drive. Your best bet for the short term may be to either
    borrow a SunCD (locally or maybe from your Sun Rep) or to mount the
    CD remotely on a machine that is already up and running and can
    handle your non-Sun CDROM, and perform a network installation.

    This is not a problem for non-SPARC versions of Solaris 2.x.

    CDROMs that have been modified to use a 512 byte blocksize by default
    will work fine.

    The Sun CD-ROM FAQ explains how to patch Solaris 2.x for using a
|.    <http://saturn.tlug.org/suncdfaq/>
    non-Sun CD-ROM drive for booting/installation.  It also includes
    other information about using CD-ROM drives on Sun.

5.31) ifconfig can't find my network interface

    Only network devices configured with an address at boot
    are visible to ifconfig (i.e., if /etc/hostname.IFN exists).
    To make a interface visible to ifconfig do:

.ifconfig ifN plumb

5.32) I have an application that compiled fine, but when I run it I get:
    fatal: libfoo.so.2: can't open file: errno=2

    You need to add -R<wherethelibraryis> to the link command line.
    E.g.,:

.cc -L/usr/dt/lib -L/usr/openwin/lib \
..-R/usr/dt/lib -R/usr/openwin/lib \
..xprog.c -lXm -lXt -lX11

5.33) Motif programs dump core almost immediately.

    You must specify the Motif library on the command line before other
    X libraries.

    WRONG:
.cc .... -lXt -lXm
    RIGHT:
.cc .... -lXm -lXt

5.34) cc complains that "language optional software package not installed".

    There is no C compiler included in Solaris 2.x.  The /usr/ucb/cc script
    you are executing is a wrapper for the SunSoft C compiler which
    calls the native C compiler with the /usr/ucb includes and libraries.
    You need to get yourself a C compiler.  Alternatively,
    you may have forgotten to put the proper link from /usr/ccs/bin/ucbcc
    to /opt/SUNWspro/SCxxxx/cc in place. See also 6.1.

5.35) thr_create and other thread functions always return -1

    If you use SunPRO C 3.0 or later, you need to specify the
    commandline option ``-mt'' when compiling and linking.  If you and
    earlier version of SunPRO C or when using gcc, you'll need to
    specify -D_REENTRANT on compile command lines and -lthread on the
    link command line.  -lthread should precede -lc.

5.36) Solaris 2.4 is getting slower over time/seems to have a kernel
    memory leak.

    There are two possible causes for this kernel memory leak.

    There's a bug in the volume management device driver that when
    unloaded leaks memory: fix with patch 101907-05 (sparc) or
    101908-07 (x86).  This bug especially affects systems *not*
    running vold, as it is triggered when the kernel decides to
    unload unused device drivers.

    The NFS client cache will cache too much.  A simple workaround is to
    add ``set nrnode = 1000'' to /etc/system and reboot.  You may want
    to make this larger or smaller depending on how much memory you
    have.  A good rule of thumb is about 20-30 rnodes per MB of
    memory.

    Another possible candidate is an overflow in /tmp or other
    swap based (tmpfs) filesystems.  Check with df/du.

5.37) Why do I get ``Unable to install/attach driver 'xxx''' messages?

    The kernel complains that it can't load device drivers for
    devices you don't have.  They're harmless, ignore them.

5.38) I can't run nfs: netdir_getbyname failure, /dev/udp: bind problem

    For some reason the nfs service has disappeared from your
    /etc/services file, NIS map or NIS+ table.  You need to
    have an entry like:

    nfsd            2049/udp        nfs             # NFS server daemon (clts)
    nfsd            2049/tcp        nfs             # NFS server daemon (cots)

    If you use NIS+, you must make sure that the NIS+ entry is readable
    for the machine executing nfsd.

    If you used your SunOS 4.x services file, that would explain it:
    SunOS 4.x doesn't have an entry for nfsd in /etc/services,
    Solaris 2.x requires one.

    This will usually not happen until you upgrade to Solaris 2.4 or
    a later revision.  Solaris 2.3 and earlier would always consult
    /etc/services, regardless of what nsswitch.conf said.
    /etc/services does contain the right NFS entries.

    Solaris 2.4 and earlier don't have an entry for NFS over tcp, so
    this error is also likely to occur on 2.5+ NFS servers that are
    NIS/NIS+ clients of 2.4- servers.  In 2.5 the error message will look
    like:

    nfsd: Cannot get address for transport udp host \1 service nfs
    nfsd: Cannot establish NFS service over /dev/udp: transport setup problem.
    nfsd: Cannot get address for transport tcp host \1 service nfs
    nfsd: Cannot establish NFS service over /dev/tcp: transport setup problem.

5.39) Why do I get ``named[]: rt_malloc:  memdebug overflow'' errors?

    That's caused by a bug in the Solaris 2.4 named.  You need to install
    the appropriate one of the following patches:
.102479-01: SunOS 5.4: memory leak/mismanagement in in.named
.102480-01: SunOS 5.4_x86: memory leak/mismanagement in in.named

    The latest version of these patches include bind 4.9.3:
.102479-02: SunOS 5.4: DNS spoofing is possible per Cern ca-96.02
.102480-02: SunOS 5.4_x86: DNS spoofing is possible per Cern ca-96.02 

5.40) Ld dumps core on Solaris/x86

    Solaris 2.4/x86 ld dumps core when passed the "-s" option.
    Workaround: Link without the -s option and use strip on
    the resulting executable.

5.41) In Solaris 2.4 my TCP performance is extremely poor.

    Patch 101969-05 broke TCP/IP throughput.  You need to backout this
    patch or obsolete it with the kernel jumbo patch (101945-27 or
    later).  The latter is recommended.

    On Solaris 2.4 x86, later kernel jumbo patches (101946-29) triggered
    bugs in some of the ethernet cards.  This manifests itself as extremely
    poor TCP throughput.  On such systems, you need to install DU10 or
    later.

5.42) Solaris 2.4 in.tftpd is terribly slow.

    In Solaris 2.4 a bug was introduced that makes tftpboot chroot,
    while it still needs to open a socket.  The first request still
    gets a response, but all other requests meet with a 5 second delay.

    Workaround:

.mkdir /tftpboot/dev
.mknod /tftpboot/dev/udp c 11 41
.chmod 755 /tftpboot/dev; chmod 666 /tftpboot/dev/udp

    This is fixed with patch 102773-01 (sparc) and 102774-01 (x86).

5.43) I get "df: Could not find mount point ..."

    If the mount point starts with /cdrom, there's a bug in the way
    /etc/mnttab gets updated for HSFS CDroms in Solaris 2.4.  Edit
    /etc/mnttab and remove the dev= entry for those mountpoints that
    give you trouble.

    If the mount point name starts with /net/HOSTNAME, where HOSTNAME
    is some other host, it's probably Sun bug 1207057.  Try patch
    102785-01 or later (SunOS 5.4) or 102783-01 or later (SunOS 5.3).
    But if HOSTNAME is the current host, it's probably Sun bug 1220440;
    unfortunately, this bug is still open as of Jan 2nd 1996.

|*5.44) I changed root's shell, now I can't login.

    If root no longer has a valid shell, your only recourse is to
    boot single user *from CD*.

|   You need to mount the root file system and fix <mntpoint>/etc/passwd.

    If you run NIS or NIS+, you have an easier solution; just add an
    account with uid 0 but with a different username and a valid shell.
    Use that account to fix the problem with the root account.

5.45) When linking C++ programs, I get "_ex_keylock" undefined.

    You installed a patch for your C++ compiler (101910 (SPARC) or
    102486 (x86)) but forgot to install the required companion patch
    for libC.so.5.

    Fix: install patch 101242-10 (SPARC) or 102859-01 (x86) or later.

    This fix is included in Solaris 2.5+.

5.46) My NFS server hangs when I get filesystem full/over quota errors.

    Solaris 2.4 has a combination of problems that make running with
    quotas of or with near-full disks almost impossible.  The problems
    include writing message to /dev/console, which requires switching
    of interrupts and make the machine appear dead, clients caching
    upto 2MB of failed writes and retrying them, hammering the server
    to death.

    Fix: kernel patch 101945-32 (sparc)/101946-29 (x86) or later.
    Needs to be applied on clients as well as servers.

5.47) OpenWindows fails with "Binding Unix Socket: Invalid argument"

    This usually only happens on diskless/dataless clients.  You
    installed a new kernel jumbo patch on the server that exports /usr
    to the client and failed to read the note in the patch readme that
    says:

    NOTE:       If this patch is applied to a server, it should
                also be applied to dataless clients that also
                mount /usr from that server.  Failure to do so will
                generate this error message when openwin is started
                on the client:  "Binding Unix socket: Invalid argument".

    The fix is to apply the same kernel jumbo patch to the client.

|5.48) Why is Xsun such a memory pig, especially on the SX, S24 and FFB?

    Ps counts the mappings for the framebuffer as memory.
    Especially on the FFB where a number of different mappings
    of the device address space is used to optimize
    access this can cause large amounts of memory, but not
    physical memory, to be mapped and shown by ps.

    It's not unusual for the FFB+ (Creator3D) to show a 500MB
    process size for the X server.

    Solaris 2.3 FCS also has a number of Xsun memory leaks when using
    the SX.  Get the SX patches or upgrade to a later release of
    Solaris 2.x.

    /usr/proc/bin/pmap (new in 2.5) will show the exact mappings used
    by Xsun.  "pmap -x" (new in 2.6) will even show how much of each
    mapping is shared/private resident, etc.  If Xsun has a memory leak,
    you'll see a huge "[heap]" with pmap.

5.49) Solaris 2.5 and Solaris 2.4 patch 101945-34+ have poor TCP performance
over slow links.

    Solaris 2.5 and Solaris 2.4 kernel patch 101945-34 and later have
    a bug in their TCP retransmission algorithm that cause excessive
    retransmissions over slow links, Sun's bug ID is #1233827.

    A work around for this bug is running the following commands
    at system boot, e.g., by adding them to /etc/init.d/inetinit
    (values are in milliseconds):

./usr/sbin/ndd -set /dev/tcp tcp_rexmit_interval_min 3000
./usr/sbin/ndd -set /dev/tcp tcp_rexmit_interval_initial 3000

    someone else suggested different changes, because with the above
    retransmits when you do lose a packet take a long time.  The following
    uses a smaller value for the minimal retransmit interval but also
    limits the outgoing packet size to 536 bytes, so retransmitted packets
    are smaller and lost packets too.

./usr/sbin/ndd -set /dev/tcp tcp_rexmit_interval_min 1000
./usr/sbin/ndd -set /dev/tcp tcp_rexmit_interval_initial 3000
./usr/sbin/ndd -set /dev/tcp tcp_mss_max 536

    Patches for this bug have been released, as listed below.
    You should not combine the patches with the tcp_rexmit_interval
    setting listed here (patches listed are the first revisions
    with the fixes; newer versions fixing more problems have been
    released and can be applied instead)


.101945-42: SunOS 5.4: patch for kernel

.103169-06: SunOS 5.5: ip driver and ifconfig fixes
.103447-03: SunOS 5.5: tcp patch

.103448-03: SunOS 5.5_x86: tcp patch
.103170-06: SunOS 5.5_x86: ip driver and ifconfig fixes

.103582-01: SunOS 5.5.1: /kernel/drv/tcp patch
.103630-01: SunOS 5.5.1: ip and ifconfig patch

.103631-01: SunOS 5.5.1_x86: ip and ifconfig patch
.103581-01: SunOS 5.5.1_x86: /kernel/drv/tcp patch

.103632-01: SunOS 5.5.1_ppc: ip and ifconfig patch
.103583-01: SunOS 5.5.1_ppc: /kernel/drv/tcp patch


5.50) After install x86 patch 101946-29, I have problems with sockets and
    TCP/IP throughput.

    These are two unrelated problems.  To fix the socket problem, either
    copy "sockmod" from an earlier kernel patch such as 101946-12 or
    install patch 101946-35.

    The performance problem is a device driver problem that doesn't
    affect all ethernet cards.  To fix this problem, you need to
    install DU10 or later.

5.51) Du and ls show funny block counts on NFSv3 mounted filesystems.

    The first release of Solaris 2.5 NFS V3 has a bug in calculating
    the block allocations returned by stat.  The server returns a
    value that is 16 times the right value and the client returns
    a value 16 times smaller to stat().

    The net effect is that unpatched Solaris 2.5 machines look like
    they're having no problems with each other.

    But on clients with the bug, files on servers returning the right value
    will have a block count 16 times too small.  This breaks NFS v3 swap
    files in Solaris 2.5, as swap files will seem to have holes in them
    and swap will refuse to use them.  If you see this problem, your server
    needs patching.

    On correct clients served by buggy servers, files will appear to
    have 16 times as many blocks allocated as they should have.
    This will generally do no more damage than overly large du(1) or
    "ls -s" output.

    There are two ways to fix this: one is to upgrade to Solaris 2.5.1,
    the other is to install the 2.5 NFS patches 103226 (SPARC) or
    103227 (x86), revision -04 or later.   As of this writing,
    patch 103226 has been superseded by patch 103477-06 (or later).

    It is important that these patches are installed on clients and servers
    alike, especially on 2.5 clients using NFS swap files.

5.52) When I halt/reboot my system I get "INIT: failed write of utmpx entry"

    When the system shuts down, init(1m) updates /var/adm/utmp* to
    reflect that fact.

    If you have a separate /var filesystem, this operation will happen
    *after* /var is unmounted and init complains:

    INIT: failed write of utmpx entry:"s6"
    INIT: failed write of utmpx entry:"rb"

    You can safely ignore these messages.

5.53) Patch installation often fails with "checkinstall" errors.

    When installing a patch, the Solaris 2.5+ patch installation
    procedure will execute the script "checkinstall" with uid nobody.

    If any of the patch files cannot be read by nobody or if any part
    of the path leading up to the patch directory an error similar to
    the following will appear:

    ./installpatch .
    Generating list of files to be patched...
    Verifying sufficient filesystem capacity (exhaustive method) ...
    Installing patch packages...
    pkgadd: ERROR: checkinstall script did not complete successfully
    ....

    You can workaround this in two ways, one is to make sure that
    nobody can read all patch files and execute a "pwd" in the patch
    directory or add an account "install" to /etc/passwd:

.install:x:0:1:installpatch braindamage:/:/bin/true

    Installpatch uses "nobody" as a fallback if it cannot find the "install"
    user.

5.54) Why do I get a CPU-bound rpc.ttdbserverd process?

    rpc.ttdbserverd is the RPC-based ToolTalk database server.  It creates and
    manages database files kept in TT_DB directories.  See ttdbserverd(1M).

    The problem is usually caused by corrupted entries in some TT_DB
    directory.  The solution is therefore to kill the running
    rpc.ttdbserverd, and to completely remove all local TT_DB directories.

    rpc.ttdbserverd will be restarted from inetd when it is needed again.
    And it will rebuild the TT_DB directories automatically.

    By default these TT_DB directories are created in the top directory of
    every filesystem, however one can use /etc/tt/partition_map to tell
    ttdbserverd where to put them.  See partition_map(4) for more details.

    A second possible cause is running out of filedescriptors, which can
    be fixed by upping the soft limit on the number of filedescriptors
    rpc.ttdbserverd starts with.

5.55) What is /proc?  Can I safely remove the large files there?

    The /proc filesystem is a memory image of each process; it's a
    virtual filesystem that occupies no disk space.

    /proc is used for programs such as ps(1) and top(public domain)
    and all the tools in /usr/proc/bin that can be used to examine
    process state.

    The only way to remove /proc is to unmount it, but that will break
    a lot of useful programs.

|*5.56) What does "named[XX]: Lame server on 'hostname' ...." mean?

    The new named as shipped in Sun's latest bind patches prints message
    about all kinds of configuration problems.

|   This particular message indicates that named has learned from a
|   nameserver that a particular domain is served by a particular
|   nameserver.  When asked, however, that nameserver denies all
|   knowledge of the particular domain.

    This is known as a "lame delegation", a reference that points nowhere.
|   If the lame server isn't yours, there's nothing you can do
|   about it.

|*5.57) I installed Solaris on a big disk, but now booting fails.

    Due to limitations in Openboot PROMs, you can't boot any of the 32bit
    SPARCs (sun4c, sun4m, sun4d) from a root partition that has parts lying
    beyond the 2GB mark on a SCSI disk.

|   On systems with really old PROMs (revision 2.5 or less) you need to
|   make the root partition smaller than 1GB.

    The Ultra PROMs are capable of this, but Solaris prior to version 2.6
    also has a bug which effectively prevents Ultras from booting from
    large root partitions too.

|5.58) My Ultra shuts down with "WARNING: THERMAL WARNING DETECTED!!!"

    The Ultras have environmental sensors that will cause system or board
    shutdowns in case of overheating.  The typical cause of this warning is
    a blocked airflow or a broken CPU fan.


6. SOFTWARE DEVELOPMENT

6.1) Where is the C compiler or where can I get one?

    Where have you been? :-) Sun has dropped their old K&R C
    compiler, supposedly to create a market for multiple compiler
    suppliers to provide better performance and features.  Here
    are some of the contenders:

    1) SunPro C: <http://www.sun.com/sunsoft/>

    SunPro, SMCC, and various distributors sell a new
    ANSI-standard C compiler on the unbundled (extra cost)
    SPARCcompiler/SPARCworks CD-ROM.  There are some other nice
    tools there too, like a "make tool" and a visual diff
    (interactive diff).

    You have to license and pay per concurrent user.

    2) Apogee compilers
.    <http://www.apogee.com/>

    Apogee sells C, C++, f77 and f90 compilers, mainly for SPARC.
    These compiler include the KAP preprocessors from Kuck and
    Associates.

    3) Cygnus GCC: <http://www.cygnus.com/>

    Cygnus Support and the Free Software Foundation make the GNU C
    compiler for Solaris, a free software product.  Source code
    and ready-to-run binaries can be installed from the CDware CD
    (Volume 4 or 5).

    Like all GNU software, there are no restrictions on who can
    use it, how many people can use it at a time, what machines it
    can be run on, or how many copies you can install, run, give
    away, or sell.

    Cygnus sells technical support for these tools, under annual
    support contracts.

    The Cygnus distribution includes:
    gcc (ansi C compiler), gdb (good debugger), byacc (yacc repl),
    flex (lex repl), gprof, makeinfo, texindex, info, patch,
    cc (a link to gcc)

    The Cygnus compiler on uunet is starting to show its age a
    bit.  If you want to compile X11R5, you can get the latest
    version of GCC in source code, from the usual places
    (prep.ai.mit.edu or one of the many mirrored copies of it).
    Build and install that compiler using the Cygnus gcc binaries.
    Or get tech support from Cygnus; they produce a new version
    for their customers every three months, and will fix any
    bug you find.

    4) Gcc.

    Gcc is available from the GNU archives in source form.  You need
    gcc 2.3.3 or later.  You should not use GNU as or GNU ld.  Make
    sure you run just-fixinc if you use a binary distribution.  Better
    is to get a binary version and use that to bootstrap gcc from
    source.

    GNU software is available from:

.    prep.ai.mit.edu:/pub/gnu
.    gatekeeper.dec.com:/pub/GNU
.    ftp.uu.net:/systems/gnu
.    wuarchive.wustl.edu:/mirrors/gnu
.    nic.funet.fi:/pub/gnu

    When you install gcc, don't make the mistake of installing
    GNU binutils or GNU libc, they are not as capable as their
    counterparts you get with Solaris 2.x.

    5) Info on other compiler vendors will be added if you send us some.

|*6.2) What about the linker, the assembler and make?

    Solaris ships with everything you need, except for the compiler.
    All this stuff lives in /usr/ccs/bin and /usr/ccs/lib.
    If you still can't find it, make sure you have the following
    packages installed on your system:

.for tools (sccs, lex, yacc, make, nm, truss, ld, as):
.    SUNWbtool, SUNWsprot, SUNWtoo
.for libraries & headers:
.    SUNWhea, SUNWarc, SUNWlibm, SUNWlibms
|.    SUNWdfbh, SUNWcg6h, SUNWxwinc, SUNWolinc,
|.    SUNWxglh
.for ucb compat:
.    SUNWsra, SUNWsrh

|   These packages are all on the Solaris 2.x CD, except that some
|   packages may only exist in some releases and not in others.

6.3) Where has ranlib gone?

    The functionality provided by ranlib in SunOS 4.1.x is now
    merged into ar.  It is no longer necessary to run ranlib
    on archive libraries.  Fix makefiles that require ranlib
    by replacing it with "/bin/true".

    A no-op ranlib has been reintroduced in 2.5.

6.4) What do I need to compile X11R5?

    There are several "patch kits" for X11R5 under Solaris 2.1.
    Most of them require gcc 2.3.3 or later and you must have
    run "fixincludes" when you install the gcc software.

    The recommended patchkit is R5.SunOS5.patch.tar.Z available
    from ftp.x.org:/R5contrib.  It works with gcc (2.3.3 or later)
    and SunPRO C.

    X11R6 compiles out-of-the-box on Solaris 2.3.

6.5) I can't compile X11R6 on Solaris 2.4

    There are several possible problems when compiling X11R6 on Solaris 2.4,
    all are solved after applying R6 fixes upto and including fix-12.
    These problems are:

    The compilation of xc/programs/Xserver/Xext/shm.c will fail with
    a redefinition of shmat().

    Compilation errors when using SC 2.0.x.

    See also 6.6

6.6) X11R6 on Solaris 2.4 won't run.  Xinit dies with "User Signal 1".
    Xterms won't die. Dired doesn't work in emacs-19.

    Some changes in libc.so and libthread.so break the way libthread is
    linked with libX11.so.  The most noticeable symptoms are failing
    signal handling in xinit, xterms that don't die after the inferior
    shell process exits and emacs-19 hanging after starting dired.

    Apply all fixes upto fix-12 to the X11R6 sources.  Remember to
    change OSMinorVersion to 4 in xc/config/cf/sun.cf as well and use
    "make Everything" or "make World", not just "make".  Make sure you
    change the right OSMinorVersion in sun.cf, the first one is the x86
    minor version, the second one is SPARC one.  Change the one
    appropriate for your system or change both.

    The resulting R6 will not run on Solaris 2.3 or earlier.
    If you want to have the same set of binaries for Solaris 2.3
    and 2.4, you need to disable threaded X altogether by changing
    "#define ThreadedX YES" to "#define ThreadedX NO" in sun.cf.

    Note that you must reinstall the X libraries with "make install"
    before things start working.  There is no need to reinstall
    anything but libX11.so.  Xterm, emacs etc., should start working
    after the change to libX11 is installed.  Check your newly
    installed libX11 with dump -Lv libX11.so.6.  If it still shows
    libthread as "NEEDED", the rebuild didn't work correctly.  Double
    check your changes.  (If you previously used the patch from the FAQ,
    make sure you remove it before applying fix-12.)

    For multi-threaded X to work it necessary to install patch 101925-02
    to fix problems in header files [2.4].  You need to reinstall gcc
    or re-run just-fixinc after installing that patch.

6.7) I get undefined symbols when compiling R6 in Solaris 2.2.

    Solaris 2.2 doesn't have the full thread support required
    by X11R6.  Compile R6 without multi-thread support or
    upgrade to 2.3 or later.

6.8) After compiling X11R6 with gcc 2.7.0, X programs won't find their
libraries.

    Someone at GNU made a bad mistake by adding a the following
    misfeature to gcc 2.7.0: in the absence of -R options, specify
    a -R option for each -L option on the commandline.

    While this looks "neat" on the surface, this makes ld ignore
    LD_RUN_PATH, which is the mechanism used by R6 to set the RPATH.
    It also introduces a security hole, as it sets a relative RPATH for
    all X executables, including the set-uid ones.

    Workaround:

    remove the following bit from the gcc-lib/.../2.7.0/specs file:

.%{!static:%{!R*:%{L*:-R %*}}}

    then rebuild X.

    This is fixed in gcc 2.7.1

6.9) How can I run X11R6 on my SS4 w/ TCX?

    Although it is possible to switch the TCX to dumb cg3 mode and
    run X11R6 on that, Matt Landau of the X consortium said the
    following on the matter:

    "But why would you want an accelerated 24-bit framebuffer to
    behave like a dumb 8-bit framebuffer under Solaris 2?

    "OpenWindows versions 3.3 and 3.4 (bundled with Solaris 2.3 and
    Solaris 2.4 respectively) are perfectly reasonable R5-based
    implementations of X, with a perfectly good R5 server that also
    does DPS and takes advantage of the TCX.  They have none of the
    brokenness associated with the old X11/NeWS server from OpenWindows 
    versions 3.2 and before.  

    "Of course, if you want R6 libraries and apps, you can build R6 and
    run R6 applications against the OpenWindows 3.4 server, and still 
    get full benefit of the TCX.  Works just fine."

6.10) Can I run X11R6 on my SX, ZX, TCX or FFB?

    No.  Run Sun's Xsun instead, it works fine.

6.11) I can't get perl 4.036 to compile or run.

    Run Configure, and use the solaris_2_0 hints, *don't* use
    the solaris_2_1 hints and don't use the config.sh you may
    already have.  First you must make sure Configure and make
    don't find /usr/ucb/cc.  (It must use gcc or the native C
    compiler: /opt/SUNWspro/bin/cc)

    Some questions need a special answer.

    Are your system (especially dbm) libraries compiled with gcc? [y] y

    yes: gcc 2.3.3 or later uses the standard calling
    conventions, same as Sun's C.

    Any additional cc flags? [ -traditional -Dvolatile=__volatile__
    -I/usr/ucbinclude] -traditional -Dvolatile=__volatile__
    Remove /usr/ucbinclude.

    Any additional libraries? [-lsocket -lnsl -ldbm -lmalloc -lm
    -lucb] -lsocket -lnsl  -lm

    Don't include -ldbm, -lmalloc and -lucb.

    Perl 5 compiles out of the box.

6.12) I can't get sockets to work with perl.

    Some of the socket constants have changed.  E.g., SOCK_STREAM
    now has a value of 2, whereas SunOS 4.x uses a value of 1.

6.13) I have problems compiling MH 6.8.3

    The MH config file for Solaris that comes with MH 6.8.3 should work
    OK, but there are some other problems: One of the Solaris 2.x headers
    conflicts with mhn.c and inc doesn't know how to separate messages
    based on the Content-Length header.  A fix for both problems can be found
    in:

    <ftp://ftp.wins.uva.nl/pub/solaris/mh-6.8.3-diff>

6.14) I can't get XV 3.x to compile or run correctly.

    You need to get xv-3.x from ftp.cis.upenn.edu:/pub/xv.
    Don't use xv-3.01 from ftp.x.org.  The latest version, xv-3.10,
    compiles fine w/o any of the ucb stuff.

6.15) What happened to NIT? What new mechanisms exist for low-level
    network access?

    See man page DLPI(7). Try NFSWATCH 4.2 for sample code using DLPI.
    It is available by ftp from:
.ftp.ecn.purdue.edu:/pub/davy/nfswatch4.3.tar.gz
    and
.gatekeeper.dec.com:/pub/net/ip/nfs/nfswatch4.3.tar.gz

    Better yet, FTP the paper "How to Use DLPI in Solaris 2.x" by
    Neal Nuckolls of Sun Internet Engineering.  Look in
    these FTP directories:
    opcom.sun.ca:/pub/drivers/dlpi

    http://www.freebird.org/hints/papers/{dlpi,npi,tpi}.ps.Z


6.16) Where are all the functions gone that used to be in libc?

    The C library has exploded.  The manual page may give an
    indication where to find a specific function.

    Those libraries are essentially split over two directories:

.    /usr/lib /usr/ccs/lib.

    Important libraries:

./usr/lib:
.    libsocket       - socket functions
.    libnsl          - network services library

./usr/ccs/lib:
.    libgen          - regular expression functions
.    libcurses       - the SysVR4 curses/terminfo library.

    See Intro(3) for more details.

6.17) I'm still missing some functions: bcopy, bzero and friends.

    They are in /usr/ucblib/libucb.so.  The b* functions
    are replaced with the ANSI-C equivalents.  Look
    in the Solaris porting FAQ for more details.

    In Solaris 2.5, they're back in libc.so, together with many
    other commonly used BSD functions.

6.18) Can I use the source compatibility package to postpone porting?

    Not really.  The Source code compatibility package is
    compatible with BSD 4.2, not SunOS 4.1.x.  The consensus
    is that the library is broken beyond usability.
    If you use libucb to pick up some functions you need, it
    is often best to specify it *after* all other libraries and
    after libc with:

.    -lc -L/usr/ucblib -R/usr/ucblib -lucb

    or preferably:

.    -lc /usr/ucblib/libucb.a

6.19) Why doesn't readdir work?  It chops the first two characters of
    all filenames.

    You're probably linking with libucb and didn't read question
    6.18.  (Readdir in libucb.so wants you to include sys/dir.h,
    but many SunOS 4.1.x programs included <dirent.h>, consequently,
    you're mixing native <dirent.h> struct dirent with libucb
    readdir().  The symptom of this mixup is that the first two
    characters of each filename are missing.  Make sure you use a
    native compiler (default /opt/SUNWspro/bin/cc, which may not be in
    your PATH), and not /usr/ucb/cc.

6.20) Why do I get undefined symbols when linking with curses/termcap?

    It is easy to mixup the BSD libcurses and the SVR4 libcurses.
    One lives in /usr/ucblib, the other in /usr/ccs/lib, when
    you've installed SUNWarc.  Note that when you specify:

.    -L/usr/ucblib -lucb -L/usr/ccs/lib -lcurses

    you will pick the *ucb* version of libcurses, not the SVR4
    version.  If you always put libucb last, as recommended in 6.18,
    you will have no such problem.

6.21) Where are the Motif includes and libraries?

    Starting with Solaris 2.4, the package SUNWmfrun is included with
    the base OS.  It is installed under the directory /usr/dt,
    where all the CDE stuff will appear (dt stands for desktop).

    There are no Motif imake templates nor is mwm shipped with the
    base OS yet.

    Remember that you must link with -R/usr/dt/lib.

6.22) When I call semctl(), my program crashes.  It works fine elsewhere.

    The fourth argument to semctl() is a "union semun" that you need to
    define yourself.  That your programs works on other systems is
    sheer luck.  The argument passing convention on SPARC/V8 cause your
    luck to run out.  Instead of passing the contents of small structs
    and unions in registers, a copy of the struct/union is made on the
    stack and a pointer to that struct is passed.

    In short, on SPARC, passing a union containing an integer and just
    an integer, both by value, is not the same thing.  On other systems
    it sometimes is.

    Wrong, but it may work on other systems:

    semctl(sem_fd, 0, SETVAL, 1); 

    Right:

    union semun {
.int val;
.struct semid_ds *buf;
.ushort *array;
    } arg;

    arg.val = 1;

    semctl(sem_fd, 0, SETVAL, arg);

6.23) Traceroute to Solaris 2.x machines gives many timeouts.

    Solaris 2.4 and later (and Solaris 2.3 w/ high rev kernel jumbo
    patches) limit the number of ICMP error message to one
    per 500 milliseconds.  To switch off this feature, use:

./usr/sbin/ndd -set /dev/ip ip_icmp_err_interval 0

6.24) I have problems linking my application statically.

    In Solaris 2.x static linking is not supported for any of the
    system libraries.  All the functions that use /etc/nsswitch.conf
    (getXXXbyYYY, getpwXXX, etc) require the dynamic linker to
    load the code to load these functions.  It is not possible
    to write configurable/extensible functions in such a way that
    dynamic linking is not required.  E.g., you can add your own
    nsswitch.conf backend which would not be known to programs
    statically linked to only the standard backend code.

    Programs that link statically against any of the OS libraries
    may not run in the next release and are not ABI compliant.

    Programs that link statically don't get some dynamic performance
    enhancements found in the shared libraries: using hardware
    multiply/divide on systems that support it; using fast mem*()
    operations on UltraSPARC etc.  And you won't pick up performance
    enhancements in next releases: e.g., Solaris 2.5 comes with
    a 4x faster fread/fwrite and the "Name Server Cache Daemon".

    If you don't care about ABI compliance, i.e., you won't
    ship your program as a product and don't care that you may
    need to recompile after an OS upgrade, here are some of your
    options:

    Link dynamically against all but libdl:

.cc -Bstatic ....  -Bdynamic -ldl -Bstatic

    Link against dl* stubs (gethostbyXXX, getpwXXX etc won't work any
    longer):

.char *dlopen() { return 0;}
.int dlclose() { return 0;}
.char *dlsym() { return 0;}
.char *dlerror() { return "dynamic linking not loaded";}

    If you don't want any dependencies on /usr, link against the dynamic
    libs in /etc/lib:

.cc -Bstatic ... -Bdynamic -R/etc/lib -Wl,-I/etc/lib/ld.so.1 -ldl
..-Bstatic ....

    If you still get undefined symbols, check with ldd for all your
    libraries if they have any dynamic dependencies.  E.g.,

.% ldd /usr/lib/libsocket.so.1
..libnsl.so.1 =>   /usr/lib/libnsl.so.1
..libdl.so.1 =>    /usr/lib/libdl.so.1
..libc.so.1 =>     /usr/lib/libc.so.1
..libintl.so.1 =>  /usr/lib/libintl.so.1
..libw.so.1 =>     /usr/lib/libw.so.1

    tells you that if you want to link libsocket statically,
    you need to link with -lnsl -ldl -lc -lintl and -lw as well.

6.25) I get '"/usr/platform/SUNW,Ultra-1/lib/libc_psr.so.1": not in
    executable format: format not recognized' from gdb on my Ultra.

    gdb needs to be updated to understand the "V8+" executable format.

    Either install gdb 4.16 or later, or update the gdb 4.15.1
    distribution with the following patch to bfd/elf32-sparc.c and
    include/elf/common.h:

.  *** gdb-4.15.1/bfd/elf32-sparc.c       Fri Nov  3 12:30:15 1995
.  --- elf32-sparc.c        Thu Nov 23 14:44:37 1995
.  ***************
.  *** 1486,1491 ****
.  --- 1486,1492 ----
.    #define TARGET_BIG_NAME       "elf32-sparc"
.    #define ELF_ARCH      bfd_arch_sparc
.    #define ELF_MACHINE_CODE EM_SPARC
.  + #define       ELF_MACHINE_ALT1 EM_SPARC32PLUS
.    #define ELF_MAXPAGESIZE 0x10000
.    #define elf_backend_create_dynamic_sections \
.                                          _bfd_elf_create_dynamic_sections


.  *** gdb-4.15.1/include/elf/common.h     Fri Nov  3 20:20:25 1995
.  --- common.h    Thu Nov 23 14:20:07 1995
.  ***************
.  *** 83,88 ****
.  --- 83,91 ----
.    #define EM_SPARC64     11     /* SPARC v9 (not official) 64-bit */

.    #define EM_PARISC      15     /* HPPA */
.  + 
.  + #define       EM_SPARC32PLUS  18      /* Sun SPARC 32+ */
.  + 
.    #define EM_PPC               20       /* PowerPC */

 .   /* If it is necessary to assign new unofficial EM_* values, please pick large

|6.26) Does Solaris have problems with dates in the year 2000 and after?

    Internally, Solaris maintains time as the number of seconds since
    1970-01-01 00:00:00 UTC (not counting leap seconds).  This counter
    won't have any problem with dates in the year 2000; since it is
    maintained as a 32-bit signed integer value, it will work correctly
    through 2038-01-19 03:14:07 UTC, by which time Solaris (if it still
    exists) will have upgraded to a larger counter.

    Though the Solaris kernel itself shouldn't have any problems with the
    year 2000, applications themselves may have problems, partly because
    some application writers unwisely chose to represent dates using
    two-digit years, and partly because some application writers
    mistakenly thought that localtime returns the year modulo 100, when it
    actually returns the year minus 1900.  These kinds of problems are
    rarer in Solaris than with typical mainframe applications, but they
    sometimes do occur.

    A year 2000 project at Sun plans to review all libraries, unbundled
.    <http://www.sun.com/y2000/>
    software, and some 3rd party apps in search of potential year 2000
    problems, so that they are resolved well before the big day.
    Sun plans to make Solaris 2.6 year-2000 compliant when it is released.
    It also plans to issue patches for Solaris 2.5 and 2.5.1 by 1997-09-30,
    and for Solaris 1.1.1, 1.1.2, 2.3 and 2.4 by 1997-12-31.

    Sun-maintained Solaris applications with known year-2000 problems as
    of Solaris 2.5.1 (unpatched) include the following.

    * SCCS files store only the last two digits of the year, so SCCS
      stops working after 1999.  Sun plans to work around this problem
      by having SCCS interpret two digit years to be in the date range
      1969-2068; this means the revised SCCS will stop working after 2068.

    * The Solaris 1 `date' command can't set the clock past 1999.
      This bug is partly fixed in Solaris 2 `date', which supports both
      2-digit and 4-digit years; however, in Solaris 2 you should use
      4-digit years when setting the date, to avoid some remaining bugs
      with 2-digit year handling.

    * The following programs are known to have minor bugs related to using
      year-1900 instead of year modulo 100 when generating diagnostics,
      temporary file names, and the like:

.    atq fsck listen passwd sar timex ufsdump uucico uustat uuxqt xterm

    * The -me, -mm, and -ms troff macro packages all assume that
      the current date is before January 1, 2000.

    * `sortbib' mishandles bibliographies containing 2-digit years that
      span the year-2000 boundary.

    * `ckdate' rejects years after 1999.

    * Problems have been reported with installing Solaris on machines
      whose hardware date is past 1999.

    * The filemgr `find after' and `find before' operations have only 2-digit
      inputs for years, and mishandle dates after 1999.

    * cm (the calendar manager) mishandles dates after 2000-02-29.

    * In Openstep, NSCalendarDate, NSDate*, Mail, and Prefrence need
      enhancements and fixes for years past 1999.

    In addition, user applications that invoke `getdate' and `strptime' on
    2-digit years are advised to check their assumptions carefully.

    Patches for year 2000 problems will be made available for all releases
    not EOLed at January 1, 1995, in keeping with the 5 year support
    window.  This includes the Solaris releases 2.5.1, 2.5, 2.4 and 2.3 as
    well as SunOS 4.1.3_U1 and 4.1.4.

|+6.27) I can't seem to get gcc to work under Solaris 2.6


|   As with all new Solaris releases, you need to reinstall gcc after
|   upgrading.  Unfortunately, Solaris 2.6 include files don't get
|   properly fixed by fixincludes.  To fix this, apply the following
|   patch to fixinc.svr4 before building gcc.

|.*** ./fixinc.svr4.org.Thu Jun 15 23:03:29 1995
|.--- ./fixinc.svr4.Thu Sep  4 13:41:29 1997
|.***************
|.*** 189,194 ****
|.--- 189,195 ----
|..  s/__STDC__[ .][ .]*==[ .][ .]*1/defined (__STRICT_ANSI__)/g
|..  s/__STDC__[ .][ .]*!=[ .][ .]*0/defined (__STRICT_ANSI__)/g
|..  s/__STDC__ - 0 == 0/!defined (__STRICT_ANSI__)/g
|.+ .  s/__STDC__ - 0 == 1/defined (__STRICT_ANSI__)/g
|..  /^typedef[ .][ .]*[unsigned .]*long[ .][ .]*[u_]*longlong_t;/s/long/long long/
|..' $2/$file > $2/$file.sed
|..mv $2/$file.sed $2/$file

|+6.28) Gdb doesn't fully work on Solaris 2.6.

|   Solaris 2.6 defines a new interface for interaction between the
|   debugger and the runtime linker.  Previous releases don't support
|   any such interface, so debuggers would use unpublished hooks.

|   The following patch to gdb 4.16 fixes this problem.

|.--- ./gdb/solib.c.org.Sat Mar 30 06:58:51 1996
|.+++ ./gdb/solib.c.Sat Sep  6 14:48:18 1997
|.@@ -67,6 +67,7 @@

|. #ifdef SVR4_SHARED_LIBS
|. static char *solib_break_names[] = {
|.+  "rtld_db_dlactivity",
|.   "r_debug_state",
|.   "_r_debug_state",
|.   "_dl_debug_state",

|+6.29) I can't get gdb to compile with Sun's C compiler

|   Older versions of Solaris didn't declare __builtin_alloca; the
|   prototype provided for it with gdb doesn't agree with the one
|   supplied with current Solaris versions.

|.--- ./libiberty/alloca-norm.h.org.Thu Jun 29 04:15:41 1995
|.+++ ./libiberty/alloca-norm.h.Sat Sep  6 14:50:35 1997
|.@@ -5,7 +5,7 @@
|. #else /* not __GNUC__ */
|. #ifdef sparc
|. #include <alloca.h>
|.-extern char *__builtin_alloca();  /* Stupid include file doesn't declare it */
|.+extern void *__builtin_alloca();  /* Stupid include file doesn't declare it */
|. #else
|. #ifdef __STDC__
|. PTR alloca (size_t);


7. ACKNOWLEDGEMENTS

    Most of this material is either written by me or sent to me
    directly. Some of it is cribbed shamelessly from USENET postings
    in several groups.

    Thanks to all people who contributed to this FAQ,
    you know who you are.  The list is too long to be included
    in this FAQ.

--- End of Solaris 2.x FAQ -- Maintained by Casper Dik <Casper.Dik@Holland.Sun.COM> ---
--
Expressed in this posting are my opinions.  They are in no way related
to opinions held by my employer, Sun Microsystems.
Statements on Sun products included here are not gospel and may
be fiction rather than truth.
