What is picmac10 ?

It is a PIC 16C84 Programmer for the LPT-port.

Why not use David Tait's Programmer ?

Because David's programmer will not always work. He uses 4066 for switching programming voltage
and 5 volt power, and the 4066 have an on-resistance around 80 ohm, that make it a bad choice
for this application.
I have used david Tait's QBASIC-program and modified it for this programmer, and it is working
all the time.

Whitch files are included ?

PICPROG  HPL       114.493 26-05-95   19.09  The picprogrammer schematic
PICPROG  BAS        15.294 26-05-95   19.06  The picprogrammer QBASIC-program
PICPROG  RBL       401.989 26-05-95   19.26  The picprogrammer bottom lay-out
PICPROG  RBO       401.989 26-05-95   19.27  The picprogrammer bottom placement drawing
PICPROG  RKO       401.989 26-05-95   19.28  The picprogrammer pcb-size
PICPROG  RTL       401.989 26-05-95   19.25  The picprogrammer top lay-out
PICPROG  RTO       401.989 26-05-95   19.27  The picprogrammer top placement drawing

PICREAD  BAS         6.131 06-05-95   23.10  A QBASIC picreader for the same pcb

PIC16C84 HPL       114.493 26-05-95   19.14  A sample Eurocrypt-M smartcard schematic
PIC16C84 RBL       602.981 26-05-95   19.19  A sample Eurocrypt-M smartcard bottom lay-out  
PIC16C84 RBO       602.981 26-05-95   19.21  A sample Eurocrypt-M smartcard bottom placement drawing 
PIC16C84 RKO       602.981 26-05-95   19.22  A sample Eurocrypt-M smartcard pcb-size 
PIC16C84 RTL       602.981 26-05-95   19.18  A sample Eurocrypt-M smartcard top lay-out 
PIC16C84 RTO       602.981 26-05-95   19.20  A sample Eurocrypt-M smartcard top placement drawing 

MASTER   ASM        21.433 07-05-95   14.04  A sample assembler-list ready for reassembly
MASTER   HE8         7.437 16-05-95   19.43  A sample INHX8M file for the Master-uP
MASTER   ASL        33.819 07-05-95   14.19  A sample assembler-list

SLAVE    HE8         7.437 16-05-95   19.43  A sample assembler-list ready for reassembly
SLAVE    ASM        21.402 07-05-95   16.07  A sample INHX8M file for the Slave-uP
SLAVE    ASL        33.945 07-05-95   15.38  A sample assembler-list

The schematic's files and the lay-out files can be printed on a HP laserjet by the command
copy /b picprog.hpl lpt1, copy /b picprog.rbl lpt1 etc...

This smart-card is working 26-05-1995 on TV3-Denmark, TV3-Sweden, Filmnet +, TV1000, Filmmax,
TVK Cinema, Cinecinema, Canal +.

This hardware-project called picmac10 is a hobby-project, it is NOT a
commercial project. It must not be used in a commercial manner. 
Because this is a hobby-project i can't guarantee that this circuit
will work. You have to build theese pcb at your own risk...
I'm not responsible for damages, loss of money, braincells or sense of humor..... 

IMPORTANT: It is illegal to watch pay-TV programs without a subscription
	   in the countries in which a regular subscription is available.
	   Use this software only for educational purposes. THE AUTHOR
	   OF THIS SOFTWARE TAKES NO RESPONSIBILITY FOR THE LEGALITY OF
	   USING AND DISTRIBUTING THIS SOFTWARE. As far as the author is
	   concerned, this software may be used and redistributed freely.
	   

The MAN himself.

What next ?

If there will be an upgrade for MAC I don't know, but there will for sure be an upgrade
for the PIC-programmer to load from binary files, a version written in C++.
	
